SmartSolo Node Seismometers

Both have a battery capacity of around 30 days. The programming, operation and downloading procedures for both types of SmartSolo nodes are also similar.

13

14

----

15

16

= **Programming Defaults** =

17

18

The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.

19

20

[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]

21

22

[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]

23

24

FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.

25

26

Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.

27

28

Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.

29

30

If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**

31

32

In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.

33

34

Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.

35

36

GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.

37

38

Bluetooth (BB nodes only) should be turned OFF to conserve power.

39

40

We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).

41

42

43

**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!

44

45

46

= **Fieldwork Preparation** =

47

48

(% class="box warningmessage" %)

49

(((

50

**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**

51

52

**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**

53

54

**We have had good experience with the 4Tb Samsung T7 Shield drives.**

)))

== Magnets ==

If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).

60

61

== Animal-Proofing ==

62

63

We have experienced times where foxes (or some other animal) will dig up nodes and potentially carry them off for tens or hundreds of meteres. Being sanitary with the rope handles (e.g. not getting food grease on them) seems to help, as well as spraying the nodes and handles with methylated spirits et al. when deploying. There are other specialized products available depending on your environment.

= **Installation** =

(% class="box infomessage" %)

68

(((

69

**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**

70

)))

71

72

== 1. Logbook documentation ==

73

74

(((

75

**Essential Details** for field logs:

76

77

* Station name

78

* Latitude, longitude, elevation

79

* Names of team members present

80

* Date and both local & UTC time of installation/removal

81

* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)

82

* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)

83

84

[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!

85

86

== 2. Node Placement ==

87

)))

88

89

**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.

**Site Analysis**:

* **Take compass measurements away from the sensor as it will affect your measurement.**

94

* Take photographs from various angles to document the site setup thoroughly.

95

* Include a detailed site description in your notes

96

97

== 3. GPS Considerations ==

98

99

(% class="wikigeneratedid" %)

100

The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.

101

102

== 4. Visibility and Location Marking ==

103

104

**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.

**GPS Marking**:

* Use a GPS device to mark the instrument's exact location.

109

* Record this location in both your paper notes and the GPS device.

110

111

== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5. Charge Time, Pre-Deployment & Post-Deployment(%%) ==

112

113

* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.

114

* **Pre-Deployment Charging**:

115

** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.

116

117

* **Operational Duration**:

118

** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.

119

120

* **Post-Retrieval Charging**:

121

** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.

122

* **Storage and Shipping Charge Level**:

123

** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.

124

** This charge level is recommended to prevent battery damage and is safe for transportation.

125

** Nodes should not be stored fully charged, and **they should especially not be stored with 0 charge as this damages lithium batteries.**

126

127

(((

128

== 6. Data Sharing and Metadata Creation ==

)))

**GPS Data**:

* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**

**Photo Sharing**:

* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).

**Metadata File**:

* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.

142

143

== 7. Additional Best Practices ==

144

145

* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.

----

= **Seismic Station Demobilization and Documentation** =

150

151

1. (((

152

**Preparation for Demobilization**:

153

154

* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.

155

)))

156

1. (((

157

**Locating the instrument**:

158

159

* Use the downloaded GPS file to accurately locate the node for demobilization.

160

* Import this KMZ file onto your phone for easy reference and location tracking.

161

* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.

162

)))

163

1. (((

164

**Labeling Instruments for Demobilization**:

165

166

* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.

167

* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.

168

* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.

169

)))

170

1. (((

171

**Photographing the Setup Node**:

172

173

* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.

174

* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.

175

)))

176

1. (((

177

**Logging Demobilization Details**:

178

179

* Use the field logbook to note the time of demobilization, serial numbers, and station name.

180

* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.

181

)))

182

1. (((

183

**Final Checks and Equipment Removal**:

184

185

* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.

186

* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.

)))

[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]

----

= **Charging Procedure for Seismic Nodes** =

196

197

(((

198

== 1. Preparation for Charging: ==

199

200

* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.

)))

(((

== 2. Disassembling the Node: ==

205

206

* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.

)))

(((

== 3. Setting Nodes in the Charging Box: ==

211

212

* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.

)))

(((

== 4. Monitoring the Charging Process: ==

217

218

* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.

219

* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.

)))

(((

== 5. Updating Charge Status: ==

224

225

* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.

226

* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.

227

)))

228

229

[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]

[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]

----

= **Downloading and Converting Seismic Data to MiniSeed Format** =

239

240

== Node Registration and Software Setup ==

241

242

1. (((

243

**Registering Nodes in the System**:

244

245

* To begin, register the nodes in the system so the software can recognize them.

246

* Navigate to the installation folder of “SmartSoloApps SoloLite”.

247

* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).

248

* To avoid double registration, replace the file each time you register a new node.

249

)))

250

1. (((

251

**Creating a New Project in SoloLite**:

252

253

* Open the “SoloLite” software.

254

* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.

255

* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.

256

)))

257

258

== Data Downloading Process ==

259

260

1. (((

261

**Initiating Data Download**:

262

263

* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.

264

* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.

265

* Select all nodes and right-click to “force download”. This starts the download process.

266

* Completed downloads will appear as new folders in the Downloaded Data panel.

267

)))

268

1. (((

269

**Exporting Data in Readable Format**:

270

271

* Go to the “Tool” menu and select “export seismic data”.

272

* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.

273

* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.

274

* (% class="box warningmessage" %)

275

(((

276

* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**

277

278

* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**

)))

)))

== Handling Nodes During Download ==

283

284

1. (((

285

**Monitoring Download Indicators**:

286

287

* During download, green lights on nodes will blink, and associated red lights on the rack will flash.

288

* Disconnect nodes properly before unplugging anything.

289

* Be cautious: if the laptop enters sleep mode, the download will pause.

290

)))

291

1. (((

292

//**Investment in Storage Hardware**~://

293

294

* (% class="box warningmessage" %)

295

(((

296

* **Use fast external hard drives to avoid limitations in data harvesting.**

297

298

* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**

299

* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**

)))

)))

1. (((

**Metadata and Time Settings**:

304

305

* Ensure all metadata is saved with the file.

306

* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.

307

)))

308

1. (((

309

**Finalizing the Download**:

310

311

* After downloading, mark the //"D"// box on your temporary labels to indicate completion.

)))

[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]

[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]

[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]

[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]

[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]

----

= **Cleaning** =

When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.

340

341

= **Weights (for shipping)** =

342

343

The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:

344

345

1 bag + 6 SP (IGU-16HR) nodes: 18 kg

346

347

1 SP (IGU-16HR) data harvester: 21.5 kg

348

349

1 SP (IGU-16HR) charger: 26.3 kg

350

351

1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg

352

353

1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg

354

)))

355

356

(% class="col-xs-12 col-sm-4" %)

(((

(% class="box" %)

(((

**Contents**

)))

(% class="box" %)

(((

= SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =

370

371

[[image:Smartsolo IGU BD3C 5 (2).jpg]]

372

373

[[image:smartsolo.jpg]]

374

375

|(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz

376

|(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s

377

|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm

378

|(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg

379

|(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb

380

|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((

381

Lithium-ion battery contained in equipment (168.84 Wh)

UN3481 PI967 S1

)))

)))

(% class="box" %)

(((

= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =

390

391

[[image:smartsolo node.jpg]]

392

393

[[image:smartsolo node 2.jpg]]

394

395

|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz

396

|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s

397

|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm

398

|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg

399

|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb

400

|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((

401

Lithium-ion battery contained in equipment (96.48 Wh)

UN3481 PI967 S2

)))

)))

(% class="box" %)

(((

= SmartSolo BD3C-16 Portable Battery Charger =

410

411

[[image:20250729_125049.jpg]]

412

413

|**Dimensions (LxHxW)**|558 x 357 x 300mm

414

|**Input rating**|100-210V - 50/60Hz

415

|**Power**|1000W

416

|**Weight**|14.5kg

417

|**Weight with cables**|21kg

418

)))

419

420

(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)

421

(((

422

= SmartSolo IGU-16 Portable Data Harvester =

423

424

[[image:20250729_124747.jpg]]

425

426

|**Dimensions (LxHxW)**|625 x 500 x 366mm

427

|**Input rating**|100-210V - 50/60Hz

428

|**Power**|100W

429

|**Weight**|21.5 - 24kg

430

|**Slots no.**|16

431

|**Download Speed**|20MB/sec/slot

)))

(% class="box" %)

(((

= SmartSolo IGU-16 Portable Battery Charger =

437

438

[[image:20250729_124644.jpg]]

439

440

|**Dimensions (LxHxW)**|625 x 500 x 366mm

441

|**Input rating**|100-210V - 50/60Hz

|**Power**|640W

|**Weight**|26.3kg

|**Slots no.**|16

)))

(% class="box" %)

(((

= SmartSolo BD3C-5 Carry Case =

450

451

[[image:20250729_124957.jpg]]

452

453

454

|**Dimensions (LxHxW)**|590 x 225 x 405mm

|**Weight**|8.2kg

|**Slots no.**|6

)))

(% class="box" %)

(((

= SmartSolo IGU-16 3C Carry Bag =

462

463

[[image:20250729_124502.jpg]]

464

465

|**Dimensions (LxHxW)**|230 x 340 x 310mm

|**Weight**|3.6kg

|**Slots no.**|6

)))

(% class="box" %)

(((

= SmartSolo IGU-16 1C Carry Bag =

473

474

[[image:20250729_124558.jpg]]

475

476

|**Dimensions (LxHxW)**|225 x 200 x 550mm

|**Weight**|

|**Slots no.**|6

)))

)))

)))

Wiki source code of SmartSolo Node Seismometers

Applications

Navigation