Wiki source code of SmartSolo Nodes

Version 20.1 by Sima Mousavi on 2024/01/18 17:25

version	line-number	content
1.1	1	(% class="row" %)
	2	(((
	3	(% class="col-xs-12 col-sm-8" %)
	4	(((
17.1	5	= Node Setup =
	6
	7	Short term (~~30 day) battery powered nodes
	8
	9	== Pre-Fieldwork Preparation ==
	10
18.1	11	(% class="box infomessage" %)
17.1	12	(((
18.2	13	(% class="box warningmessage" %)
	14	(((
19.2	15	INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING
17.1	16	)))
18.2	17	)))
17.1	18
18.2	19	= Installation =
17.1	20
18.2	21	=== 1- Logbook documentation ===
17.1	22
18.2	23	(((
	24	Essential Details: Record the following in a logbook:
	25
	26	* Station name
	27	* Latitude and longitude
	28	* Names of team members present
	29	* Date and local time of installation
	30	* Serial number (SN) of the sensor
	31	* Detailed notes on the site conditions and setup
	32
	33	=== 2- Node Placement ===
17.1	34	)))
	35
18.2	36	Protection: Place nodes inside thick, landfill biodegradable plastic bags for environmental protection.
17.1	37
18.2	38	Site Analysis:
	39
	40	* Conduct compass measurements away from the node and metallic structures, adjusting for inclination angle.
	41	* Take multiple photographs from various angles to document the site setup thoroughly.
18.3	42	* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
18.2	43
20.1	44	=== 3- GPS Considerations ===
18.2	45
20.1	46	(% class="wikigeneratedid" %)
	47	The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
	48
	49	=== 4- Visibility and Location Marking ===
	50
18.2	51	Flag Placement: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
	52
	53	GPS Marking:
	54
	55	* Use a GPS device to mark the instrument's exact location.
	56	* Record this location in both your paper notes and the GPS device.
	57
20.1	58	=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5- Charge Time, Pre-Deployment & Post-Deployment(%%) ===
18.3	59
20.1	60	* Charging Duration: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
	61	* Pre-Deployment Charging:
	62	** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge right before deployment.
	63
	64
	65	* Operational Duration:
	66	** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle.
	67
	68
	69	* Post-Retrieval Charging:
	70	** Do not store the instruments with completely drained batteries.
	71	** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) for optimal battery health.
	72
	73
	74	* Storage and Shipping Charge Level:
	75	** Maintain a battery charge level of around 50-60% for both storage and shipping purposes.
	76	** This charge level is recommended to prevent battery damage and is safe for transportation.
	77
	78	=== ===
	79
	80	=== ===
	81
	82	=== 6- Data Sharing and Metadata Creation ===
	83
18.3	84	GPS Data:
	85
	86	* Download the GPS file to a laptop.
	87	* Share this file on a drive accessible to all team members for uniform understanding of node locations.
	88
	89	Photo Sharing:
	90
	91	* Upload site photos to a shared platform (OneDrive, Dropbox, etc.).
	92	* Integrating photos into Google Maps or Google Earth can be particularly beneficial for easy location referencing.
	93
	94	Metadata File:
	95
	96	* Create a metadata XML file for each node, which is essential for data organisation and future reference.
	97
20.1	98	=== 7- Additional Best Practices ===
18.3	99
	100	* Environmental Responsibility: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
	101	* Training and Familiarisation: Make sure all team members are adequately trained in using the GPS devices, compass, and other equipment to ensure consistent and accurate data collection.
	102
19.2	103	* (((
	104	==== Keeping the Instruments Clean ====
	105	)))
	106	* (((
	107	Use a (landfill, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
	108	)))
	109
18.3	110	= =
	111
3.2	112	= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
1.1	113
	114	blahblah
	115
	116	== Sub-paragraph ==
	117
	118
11.1	119	== ==
1.1	120
	121
6.3	122	= Smart Solo BD3C-5 (5 second) Broad-Band Node =
1.1	123
6.3	124	Lorem
1.1	125
14.1	126	[[image:1705196270090-364.png]]
1.1	127
8.2	128
3.2	129	== GPS Considerations ==
1.1	130
3.2	131	The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
1.1	132
8.2	133	= Keeping the Instruments Clean =
1.1	134
10.1	135	Use a (landfill, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
6.3	136
	137
	138	= Charge Time, Instrument Life, and Charge During Storage & Shipping =
	139
	140	Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
	141
	142	Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
7.1	143
	144
	145	= Best Practices and Guide =
	146
7.2	147	== Install ==
7.1	148
	149	Logbook is required (used again for pick up & metadata creation)
	150
	151	- station name
	152
	153	- lat / long
	154
	155	- team members
	156
	157	- date and local time
	158
	159	- SN of sensor
	160
	161	- notes on site
	162
	163	Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
	164
	165	Take compass measurement away from node and fences [make sure to adjust inclination angle]
	166
	167	Take many photos from the site from different angles
	168
	169	Add a precise site description to the notes such as distances and orientations from landmarks
	170
	171	It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
	172
	173	Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
	174
	175	Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
	176
	177	Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
	178
	179	Create metadata .xml file
	180
	181
7.2	182	== Removing/Demob ==
7.1	183
	184	Download and then use the GPS file to locate the node
	185
	186	Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.
	187
	188
7.2	189	Upload photos of the site
7.1	190
	191	- station name
	192
	193	- latitude
	194
	195	- longitude
	196
	197	- elevation
	198
	199	* SN of sensor – SN of battery (optional)
7.2	200	* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
7.1	201
	202	Upload photos into Google Earth and on a shared drive
	203
	204	Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!).
	205
8.1	206	Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
7.1	207
	208	Take a photo of the entire setup node with the label on it + compass
	209
	210	Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
	211
	212
	213	== Charging ==
	214
	215	Clean node prior to charging and harvesting the data
	216
	217	Remove battery (and spike) from the sensor by twisting the spike part of the instrument
	218
	219	Set 16 nodes into the charging box (spikes up)
	220
	221	Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
	222
	223	This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
	224
14.1	225	[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png\|\|data-xwiki-image-style-alignment="center"]]
7.2	226
8.1	227
	228
7.2	229	== Downloading and Converting Data to MiniSeed ==
	230
	231
	232	The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
	233
14.1	234	[[image:1705195543887-977.png]]
7.2	235
8.3	236
7.2	237	Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
	238
14.1	239	[[image:1705195543890-537.png\|\|data-xwiki-image-style-alignment="center"]]
7.2	240
8.3	241
7.2	242	Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
	243
14.1	244	[[image:1705195543891-334.png\|\|data-xwiki-image-style-alignment="center"]]
7.2	245
8.3	246	At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
7.2	247
8.3	248	(% class="box warningmessage" %)
	249	(((
	250	Please make sure that data is exported as "COUNTS" and NOT "mV"!
	251	)))
	252
	253	(% class="box warningmessage" %)
	254	(((
	255	Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.
	256	)))
	257
	258	A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
	259
7.2	260	Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
	261
14.1	262	[[image:1705195543898-365.png\|\|data-xwiki-image-style-alignment="center"]]
7.2	263
	264	When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
	265
8.3	266	(% class="box infomessage" %)
	267	(((
	268	INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
	269	)))
7.2	270
	271	When downloading, ensure that all metadata is saved along with the file.
	272
8.1	273	Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
	274
	275	//Once downloaded, mark the "D" box on your temporary labels!//
	276
	277	== Converting data ==
	278
	279	Check the data all have been converted to miniseed correctly
	280
	281	– 3 files per station per day
	282
	283	* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
	284	* ~~ 5 Gb / node / month
	285
	286	//Tick ‘R’ box on the node label//
	287
	288
8.2	289	== Cleaning ==
8.1	290
	291	If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
	292
	293
1.1	294	)))
	295
	296
	297	(% class="col-xs-12 col-sm-4" %)
	298	(((
10.1	299	(% class="box" %)
	300	(((
	301	Contents
1.1	302
10.1	303	(% class="wikitoc" %)
	304	* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
	305	** [[Sub-paragraph>>path:#HSub-paragraph]]
	306	** [[ >>path:#H]]
	307	* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
	308	** [[GPS Considerations>>path:#HGPSConsiderations]]
	309	* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
	310	* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
	311	* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
	312	** [[Install>>path:#HInstall]]
	313	** [[Removing/Demob>>path:#HRemoving2FDemob]]
	314	** [[Charging>>path:#HCharging]]
	315	** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
	316	** [[Converting data>>path:#HConvertingdata]]
	317	** [[Cleaning>>path:#HCleaning]]
	318	)))
1.1	319
8.6	320
11.1	321	(% class="box" %)
10.1	322	(((
11.1	323	= SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
12.1	324
15.1	325	[[image:Smartsolo IGU BD3C 5 (2).jpg]]
	326
16.1	327	[[image:smartsolo.jpg]]
	328
13.2	329	\|(% style="width:189px" %)Frequency Band\|(% style="width:221px" %)5 Seconds to 150Hz
	330	\|(% style="width:189px" %)Sensitivity\|(% style="width:221px" %)200 V/m/s
	331	\|(% style="width:189px" %)Size (without spike)\|(% style="width:221px" %)158 x160mm
	332	\|(% style="width:189px" %)Weight\|(% style="width:221px" %)2.8 kg
	333	\|(% style="width:189px" %)Data Storage\|(% style="width:221px" %)64 Gb
	334	\|(% style="width:189px" %)Battery\|(% style="width:221px" %)Li_etc XXAh
12.1	335	)))
11.1	336
12.1	337	(% class="box" %)
	338	(((
	339	= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
11.1	340
16.1	341	[[image:smartsolo node.jpg]]
	342
	343	[[image:smartsolo node 2.jpg]]
	344
13.2	345	\|(% style="width:187px" %)Frequency Band\|(% style="width:224px" %)5 Hz to 1652Hz
	346	\|(% style="width:187px" %)Sensitivity\|(% style="width:224px" %)67.7 V/m/s
	347	\|(% style="width:187px" %)Size (with spike)\|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
16.1	348	\|(% style="width:187px" %)Weight\|(% style="width:224px" %)2.3 kg
13.2	349	\|(% style="width:187px" %)Data Storage\|(% style="width:224px" %)64 Gb
	350	\|(% style="width:187px" %)Battery\|(% style="width:224px" %)Li_etc XXAh
10.1	351	)))
4.1	352
9.2	353
1.1	354	)))
	355	)))

Wiki source code of SmartSolo Nodes

Applications

Navigation