Skip to Content
Last modified by robert on 2026/01/19 17:43
From version 95.1
edited by KB
on 2026/01/19 13:40
Change comment: There is no comment for this version
To version 49.1
edited by robert
on 2024/05/28 12:32
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SmartSolo Node Seismometers
1 +SmartSolo Nodes
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.KB
1 +XWiki.robert
Content
... ... @@ -4,106 +4,64 @@
4 4  (((
5 5  = **Node Types** =
6 6  
7 -ANSIR supply two types of three-channel nodes, and one type of one-channel node:
7 +ANSIR carry two types of three-channel nodes
8 8  
9 -* **SmartSolo IGU 16HR 3C (5 Hz, 'very' short period)**
10 -* **SmartSolo BD3C-5 (5 second, short period)**
11 -* **SmartSolo IGU 16 1C (5 Hz, 'very' short period, single channel)**
9 +* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 +* **SmartSolo BD3C-5 (5 Second Broad-Band)**
12 12  
13 -The three-channel nodes have a theoretical battery capacity of ~~30 days, whereas the single-channel type has a capacity of ~~50 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
12 +Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
14 14  
15 -(% class="box infomessage" %)
16 -(((
17 -**Freight update, 2026: **Freight options for lithium-ion batteries are changing in 2025/2026 to comply with updated transport safety regulations. This will impact supply of IGU 16 (<100Wh) and BD3C (168Wh) nodes. Advice will be sought from freighters on a case-by-case basis while they implement new guidelines.
18 -)))
19 19  
20 20  ----
21 21  
22 22  = **Programming Defaults** =
23 23  
24 -The nodes must be programmed in the SoloLite software prior to use. The screenshots below show our recommended parameters for the 5 Hz (16HR-3C) and 5 second (BDC3-5) nodes.
19 +ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
25 25  
26 -[[IGU-16 3C programming screen set at 250 Hz. Ensure that the circled areas are set!>>image:5Hz_node_programming.labels.png||alt="IGU-16 3C programming screen"]]
27 27  
28 -[[BD3C-5 programming screen set at 250 hz. Ensure that the circled areas are set!>>image:5S_node_programming.labels.png||alt="BD3C-5 programming screen"]]
29 -
30 -FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
31 -
32 -Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
33 -
34 -Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
35 -
36 -If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
37 -
38 -In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
39 -
40 -Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
41 -
42 -GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
43 -
44 -Bluetooth (BD3C-5 only) should be turned OFF to conserve power.
45 -
46 -We recommend that the 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
47 -
48 -{{info}}
49 -**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
50 -{{/info}}
51 -
52 52  = **Fieldwork Preparation** =
53 53  
24 +(% class="box infomessage" %)
25 +(((
54 54  (% class="box warningmessage" %)
55 55  (((
56 56  **INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
57 57  
58 58  **Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
59 -
60 -**We have had good experience with the 4Tb Samsung T7 Shield drives.**
61 61  )))
32 +)))
62 62  
63 -== Magnets ==
64 -
65 -If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).
66 -
67 -== Animal-Proofing ==
68 -
69 -We have experienced interference from animals (foxes, dogs, goats) digging up and carrying nodes off for tens or hundreds of metres. It is helpful to minimise human and food smells (particularly on the rope handles) when working in areas where this is a risk. Or, wipe down affected nodes with 50-80% methylated spirits if extensive handling can not be avoided.
70 -
71 71  = **Installation** =
72 72  
73 -(% class="box infomessage" %)
74 -(((
75 -**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
76 -)))
36 +== **1. Logbook documentation** ==
77 77  
78 -== 1. Logbook documentation ==
79 -
80 80  (((
81 -**Essential Details** for field logs:
39 +**Essential Details**: Record the following in a logbook:
82 82  
83 83  * Station name
84 -* Latitude, longitude, elevation
42 +* Latitude and longitude
85 85  * Names of team members present
86 -* Date and both local & UTC time of installation/removal
87 -* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
88 -* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
44 +* Date and local time of installation
45 +* Serial number (SN) of the sensor
46 +* Detailed notes on the site conditions and setup
89 89  
90 -[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
91 -
92 -== 2. Node Placement ==
48 +== **2. Node Placement** ==
93 93  )))
94 94  
51 +**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
52 +
95 95  **Site Analysis**:
96 96  
97 97  * **Take compass measurements away from the sensor as it will affect your measurement.**
98 -* Take photographs from various angles to document the site setup thoroughly.
99 -* Include a detailed site description in your notes
56 +* Take multiple photographs from various angles to document the site setup thoroughly.
57 +* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
100 100  
101 -== 3. GPS Considerations ==
59 +== **3. GPS Considerations** ==
102 102  
103 103  (% class="wikigeneratedid" %)
104 104  The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
105 105  
106 -== 4. Visibility and Location Marking ==
64 +== **4. Visibility and Location Marking** ==
107 107  
108 108  **Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
109 109  
... ... @@ -112,7 +112,7 @@
112 112  * Use a GPS device to mark the instrument's exact location.
113 113  * Record this location in both your paper notes and the GPS device.
114 114  
115 -== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5. Charge Time, Pre-Deployment & Post-Deployment(%%) ==
73 +== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5. Charge Time, Pre-Deployment & Post-Deployment**(%%) ==
116 116  
117 117  * **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
118 118  * **Pre-Deployment Charging**:
... ... @@ -122,22 +122,19 @@
122 122  ** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
123 123  
124 124  * **Post-Retrieval Charging**:
125 -** After retrieval, charge the instruments to about 50-60% (indicated by ORANGE LED) unless they are to be immediately re-deployed or transported.
126 -* **State of Charge (SoC) for Storage**:
127 -** Maintain a battery charge level of around 50-60% (i.e., ORANGE) for storage.
128 -** This charge level is recommended to prevent battery damage, and should be checked every six months.
129 -** Nodes should //__not be stored at full-charge (GREEN), or 0-charge (RED).__//
130 -** Storage at 0-charge damages lithium batteries**.**
131 -* **SoC for Transport:**
132 -** Charge levels for transport will be advised by the freighter. The required SoC will depend on volume and transport method (air, land, sea).
83 +** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
84 +* **Storage and Shipping Charge Level**:
85 +** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
86 +** This charge level is recommended to prevent battery damage and is safe for transportation.
87 +** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
133 133  
134 134  (((
135 -== 6. Data Sharing and Metadata Creation ==
90 +== **6. Data Sharing and Metadata Creation** ==
136 136  )))
137 137  
138 138  **GPS Data**:
139 139  
140 -* Ensure you have __carefully documented__ precise lat/lon locations for each station.
95 +* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
141 141  
142 142  **Photo Sharing**:
143 143  
... ... @@ -145,12 +145,20 @@
145 145  
146 146  **Metadata File**:
147 147  
148 -* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.
103 +* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]].
149 149  
150 -== 7. Additional Best Practices ==
105 +== **7. Additional Best Practices** ==
151 151  
107 +* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
152 152  * **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
153 153  
110 +* (((
111 +==== **Keeping the Instruments Clean** ====
112 +)))
113 +* (((
114 +Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
115 +)))
116 +
154 154  ----
155 155  
156 156  = **Seismic Station Demobilization and Documentation** =
... ... @@ -202,34 +202,32 @@
202 202  = **Charging Procedure for Seismic Nodes** =
203 203  
204 204  (((
205 -== 1. Preparation for Charging: ==
168 +== **1. Preparation for Charging**: ==
206 206  
207 207  * Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
208 208  )))
209 209  
210 210  (((
211 -== 2. Disassembling the Node: ==
174 +== **2. Disassembling the Node**: ==
212 212  
213 -* For the IGU-16HR, remove the battery section (bottom half) from the sensor by unscrewing the spike section counter-clockwise.
176 +* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
214 214  )))
215 215  
216 216  (((
217 -== 3. Setting Nodes in the Charging Box: ==
180 +== **3. Setting Nodes in the Charging Box**: ==
218 218  
219 -* Connect to a safe indoor power supply, and turn on (red rocker switch).
220 -* Charging will begin automatically when nodes are inserted in the charging rack.
221 -* Place IGU-16HR battery sections upside-down in the rack, oriented with the terminal connectors.
182 +* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
222 222  )))
223 223  
224 224  (((
225 -== 4. Monitoring the Charging Process: ==
186 +== **4. Monitoring the Charging Process**: ==
226 226  
227 -* Lights adjacent to the batteries will illuminate, indicating that charging is underway.
228 -* Observe the transition of the lights from steady RED to ORANGE, then GREEN, and finally to FLASHING GREEN. A flashing green light indicates the batteries are fully charged.
188 +* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
189 +* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
229 229  )))
230 230  
231 231  (((
232 -== 5. Updating Charge Status: ==
193 +== **5. Updating Charge Status**: ==
233 233  
234 234  * During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
235 235  * This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
... ... @@ -240,29 +240,14 @@
240 240  
241 241  
242 242  
243 -{{{
244 - }}}
204 +[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
245 245  
246 246  ----
247 247  
248 248  = **Downloading and Converting Seismic Data to MiniSeed Format** =
249 249  
250 -(% class="wikigeneratedid" %)
251 -SmartSolo provides the following powerpoint for SmartSolo node programming and operation. Note that ANSIR only uses a portion of their process for our own uses: [[https:~~/~~/nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf>>url:https://nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf]]
210 +== **Node Registration and Software Setup** ==
252 252  
253 -== Connection tips: ==
254 -
255 -Connecting SmartSolo nodes to their harvesters and having SoloLite recognise them can be a bit tricky, here are some tricks to help register and program them easier:
256 -
257 -* Place the node on the harvester gently, then firmly press it down onto the pins.
258 -* Place all nodes onto the harvester before trying any troubleshooting, as they may not show up while the SoloLite software is running. Once all are connected, try restarting the software for them to be recognised.
259 -* If a node is refusing to connect, try it with another slot. It is easiest if you place all 16 nodes on the harvester, and swap any nodes that refuse to connect with each other.
260 -* Nodes will likely not show up in the order that they should, though this is not an issue. E.g, a node in slot 6 on the harvester may show up in port 13 in the SoloLite software. Annoying, but it doesn't matter so long as you keep track of what's been harvested!
261 -
262 -
263 -
264 -== Node Registration and Software Setup ==
265 -
266 266  1. (((
267 267  **Registering Nodes in the System**:
268 268  
... ... @@ -279,29 +279,8 @@
279 279  * Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
280 280  )))
281 281  
282 -== File structure ==
228 +== **Data Downloading Process** ==
283 283  
284 -There are essentially three main folders where relevant PROSPECT and PROJECT DATA is stored. Individual projects will be found as subfolders in these.
285 -
286 -=== SOLOLITE ===
287 -
288 -This folder stores SoloLite config files and parameters. Nothing too important stored here, you can always start over and re-create this.
289 -
290 -=== DCCDATA ===
291 -
292 -This folder stores the RAW data you have harvested from the nodes. The data will still be on the nodes (unless you erased it) in case of emergency, but regardless, this is the folder you want to back up and save somewhere.
293 -
294 -If you had a weird time harvesting a node, you can always manually copy it as if it were a USB stick and place it into this folder manually. The structure is: //C:/DCCDATA/prospect_name/project_name/SERIALNUMBER/label(usually a timestamp but can be anything)//
295 -
296 -Then in the SoloLite software, go to tools > Reanalyze Seismic Data
297 -
298 -=== SOLODATA ===
299 -
300 -This folder stores **exported** (e.g. miniseed) data. It is structured similarly. If your DCCDATA is intact, this can always be re-created if need be.
301 -
302 -
303 -== Data Downloading Process ==
304 -
305 305  1. (((
306 306  **Initiating Data Download**:
307 307  
... ... @@ -318,48 +318,14 @@
318 318  * Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
319 319  * (% class="box warningmessage" %)
320 320  (((
321 -* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**
246 +* **Ensure to export data as "COUNTS", not "mV".**
322 322  
323 -* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**
248 +* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db (a factor of 15.848932).**
324 324  )))
325 325  )))
326 326  
327 -== Smart Solo IGU-16HR Polarity Notice ==
252 +== **Handling Nodes During Download** ==
328 328  
329 -See [[https:~~/~~/auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug>>https://auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug]] for discussion. If data is headed to AusPass, we prefer to invert the IGU-16HR channel data manually rather than in the SoloLite software or inverting the response metadata.
330 -
331 -**The BD3C-5 data does not require a polarity inversion.**
332 -
333 -== 18 Leap Second bug ==
334 -
335 -Not so much a //bug// as much as "a thing that can happen if your SoloLite installation is corrupted". If you notice your data has large constant time offsets, you should suspect that the number of leap seconds has not been accounted properly. There is a file "smartsoloconfig.xml" that needs to be present in "C:\SmartSoloApps SoloLite" (e.g. the main program directory) that dictates the leap second offset for the last two data ranges. Since 2017-01-01, this is 18 seconds. At some point in the next few years it will be 19 seconds.
336 -
337 -If this file is missing, just create a new one structured like so, name it "smartsoloconfig.xml" and put it in your main program directory. Then, Reanalyze your data (tools > Reanalyze seismic data) and your data should have the correct time. You can also do this manually, if you want. The offset is 18 seconds precisely.
338 -
339 -{{code language="none"}}
340 -<?xml version="1.0" encoding="UTF-8"?>
341 -<config>
342 - <leapsecond>
343 - <interval>
344 - <start_time>2017-01-01#00:00:00</start_time>
345 - <end_time>2999-12-31#23:59:59</end_time>
346 - <second>18</second>
347 - </interval>
348 - <interval>
349 - <start_time>1970-01-01#00:00:00</start_time>
350 - <end_time>2017-01-01#00:00:00</end_time>
351 - <second>17</second>
352 - </interval>
353 - </leapsecond>
354 - <GPS_distance_threshold_degree>
355 - 4e-5
356 - </GPS_distance_threshold_degree>
357 -</config>
358 -{{/code}}
359 -
360 -
361 -== Handling Nodes During Download ==
362 -
363 363  1. (((
364 364  **Monitoring Download Indicators**:
365 365  
... ... @@ -375,7 +375,6 @@
375 375  * **Use fast external hard drives to avoid limitations in data harvesting.**
376 376  
377 377  * **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
378 -* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
379 379  )))
380 380  )))
381 381  1. (((
... ... @@ -415,23 +415,23 @@
415 415  
416 416  = **Cleaning** =
417 417  
418 -When assembled, the nodes are water resistant but not submersible. They can handle a good spray and wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
308 +**Procedure for Seismic Nodes:**
419 419  
310 +* If the nodes are placed in a sturdy plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
311 +
420 420  = **Weights (for shipping)** =
421 421  
422 422  The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
423 423  
424 -1 bag + 6*IGU-16HR nodes: 18 kg
316 +1 bag + 6 SP (IGU-16HR) nodes: 18 kg
425 425  
426 -1*IGU-16HR data harvester: 21.5 kg
318 +1 SP (IGU-16HR) data harvester: 21.5 kg
427 427  
428 -1*IGU-16HR charger: 26.3 kg
320 +1 SP (IGU-16HR) charger: 26.3 kg
429 429  
430 -1*BD3C-5 charger (with and without 16 cables): 21 kg / 14.5 kg
322 +1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
431 431  
432 -1 case + 5*BD3C-5 nodes: 22 kg (aggregate battery weight <5kg, 168Wh)
433 -
434 -1 case + 6*BD3C-5 nodes: 25 kg (aggregate battery weight >5kg, 168Wh)
324 +1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
435 435  )))
436 436  
437 437  (% class="col-xs-12 col-sm-4" %)
... ... @@ -455,19 +455,15 @@
455 455  
456 456  |(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
457 457  |(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
458 -|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)Φ158 x160mm(H)
348 +|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
459 459  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
460 460  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
461 -|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
462 -Lithium-ion battery contained in equipment (168.84 Wh)
463 -
464 -UN3481 PI967 S1
351 +|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
465 465  )))
466 -)))
467 467  
468 468  (% class="box" %)
469 469  (((
470 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
356 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
471 471  
472 472  [[image:smartsolo node.jpg]]
473 473  
... ... @@ -474,110 +474,13 @@
474 474  [[image:smartsolo node 2.jpg]]
475 475  
476 476  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
477 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)76.7 V/m/s
478 -|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm(H)
363 +|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
364 +|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
479 479  |(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
480 480  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
481 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
482 -Lithium-ion battery contained in equipment (96.48 Wh)
483 -
484 -UN3481 PI967 S2
367 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Lithium ion XXAh
485 485  )))
486 -)))
487 487  
488 -(% class="box" %)
489 -(((
490 490  
491 -
492 -= SmartSolo [[IGU-16>>url:https://smartsolo.com/cp-3.html]]1C =
493 -
494 -
495 -[[image:Screenshot 2025-08-01 161027.png]]
496 -
497 -|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 413Hz
498 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)80 V/m/s
499 -|(% style="width:187px" %)**Size (without spike)**|(% style="width:224px" %)95mm(L) × 103mm(W) × 118mm(H)
500 -|(% style="width:187px" %)**Weight**|(% style="width:224px" %)1.1 kg
501 -|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)8 Gb
502 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
503 -Lithium-ion battery contained in equipment (38.48 Wh)
504 -
505 -UN3481 PI967 S2
506 506  )))
507 507  )))
508 -
509 -(% class="box" %)
510 -(((
511 -= SmartSolo BD3C-16 Portable Battery Charger =
512 -
513 -[[image:20250729_125049.jpg]]
514 -
515 -|**Dimensions (LxHxW)**|558 x 357 x 300mm
516 -|**Input rating**|100-210V - 50/60Hz
517 -|**Power**|1000W
518 -|**Weight**|14.5kg
519 -|**Weight with cables**|21kg
520 -)))
521 -
522 -(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
523 -(((
524 -= SmartSolo IGU-16 Portable Data Harvester =
525 -
526 -[[image:20250729_124747.jpg]]
527 -
528 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
529 -|**Input rating**|100-210V - 50/60Hz
530 -|**Power**|100W
531 -|**Weight**|21.5 - 24kg
532 -|**Slots no.**|16
533 -|**Download Speed**|20MB/sec/slot
534 -)))
535 -
536 -(% class="box" %)
537 -(((
538 -= SmartSolo IGU-16 Portable Battery Charger =
539 -
540 -[[image:20250729_124644.jpg]]
541 -
542 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
543 -|**Input rating**|100-210V - 50/60Hz
544 -|**Power**|640W
545 -|**Weight**|26.3kg
546 -|**Slots no.**|16
547 -)))
548 -
549 -(% class="box" %)
550 -(((
551 -= SmartSolo BD3C-5 Carry Case =
552 -
553 -[[image:20250729_124957.jpg]]
554 -
555 -
556 -|**Dimensions (LxHxW)**|590 x 225 x 405mm
557 -|**Weight**|8.2kg
558 -|**Slots no.**|6
559 -)))
560 -
561 -(% class="box" %)
562 -(((
563 -= SmartSolo IGU-16 3C Carry Bag =
564 -
565 -[[image:20250729_124502.jpg]]
566 -
567 -|**Dimensions (LxHxW)**|230 x 340 x 310mm
568 -|**Weight**|3.6kg
569 -|**Slots no.**|6
570 -)))
571 -
572 -(% class="box" %)
573 -(((
574 -= SmartSolo IGU-16 1C Carry Bag =
575 -
576 -[[image:20250729_124558.jpg]]
577 -
578 -|**Dimensions (LxHxW)**|225 x 200 x 550mm
579 -|**Weight**|
580 -|**Slots no.**|6
581 -)))
582 -)))
583 -)))
20250729_124502.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -457.6 KB
Content
5Hz_node_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.KB
Size
... ... @@ -1,1 +1,0 @@
1 -109.8 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -106.7 KB
Content
Screenshot 2025-08-01 161027.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -82.8 KB
Content
XWiki.XWikiRights[0]
Allow/Deny
... ... @@ -1,1 +1,0 @@
1 -Allow
Groups
... ... @@ -1,1 +1,0 @@
1 -XWiki.XWikiAllGroup
Levels
... ... @@ -1,1 +1,0 @@
1 -comment
XWiki.XWikiRights[1]
Allow/Deny
... ... @@ -1,1 +1,0 @@
1 -Allow
Levels
... ... @@ -1,1 +1,0 @@
1 -comment
Users
... ... @@ -1,1 +1,0 @@
1 -XWiki.XWikiGuest