Changes for page SmartSolo Node Seismometers

Summary

• Page properties (3 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 13 removed)
  • 1706153266647-145.png
  • 1706153354750-415.png
  • 1706153556166-231.jpeg
  • 20250729_124502.jpg
  • 20250729_124558.jpg
  • 20250729_124644.jpg
  • 20250729_124747.jpg
  • 20250729_124957.jpg
  • 20250729_125049.jpg
  • BB_programming.labels.png
  • SP_programming.labels.png
  • Screenshot 2025-08-01 161027.png
  • example_metadata.txt
• Objects (0 modified, 0 added, 2 removed)
  • XWiki.XWikiRights[0]
  • XWiki.XWikiRights[1]

Details

Page properties

Title

...	...	@@ -1,1 +1,1 @@
1		-SmartSolo Node Seismometers
	1	+SmartSolo Nodes

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.robert
	1	+XWiki.sima

Content

...	...	@@ -2,105 +2,56 @@
2	2	(((
3	3	(% class="col-xs-12 col-sm-8" %)
4	4	(((
5		-= **Node Types** =
	5	+= **Node Setup** =
6	6
7		-ANSIR carry two types of three-channel nodes, and one type of one-channel node:
	7	+Short term (~~30 day) battery powered nodes. The default gain should be 24 db for the 16HR-3C and 6 db for the BD3C-5
8	8
9		-* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10		-* **SmartSolo BD3C-5 (5 Second Broadband)**
11		-* **SmartSolo IGU 16 1C (5 Hz Short Period, single channel)**
12	12
13		-The three-channel nodes have a battery capacity of ~~30 days, whereas the single-channel type has a capacity of ~~50 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
	10	+~*~**this needs to be reformatted
14	14
15		-----
	12	+== **Pre-Fieldwork Preparation** ==
16	16
17		-= **Programming Defaults** =
18		-
19		-The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.
20		-
21		-[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]
22		-
23		-[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]
24		-
25		-FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
26		-
27		-Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
28		-
29		-Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
30		-
31		-If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
32		-
33		-In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
34		-
35		-Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
36		-
37		-GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
38		-
39		-Bluetooth (BB nodes only) should be turned OFF to conserve power.
40		-
41		-We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
42		-
43		-{{info}}
44		-**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
45		-{{/info}}
46		-
47		-= **Fieldwork Preparation** =
48		-
	14	+(% class="box infomessage" %)
	15	+(((
49	49	(% class="box warningmessage" %)
50	50	(((
51	51	**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
52	52
53		-**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
54		-
55		-**We have had good experience with the 4Tb Samsung T7 Shield drives.**
	20	+**Plan on 1 Tb to store ALL data for 50 nodes @ 250 Hz and a single ~~30 day occupation**
56	56	)))
	22	+)))
57	57
58		-== Magnets ==
59		-
60		-If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).
61		-
62		-== Animal-Proofing ==
63		-
64		-We have experienced times where foxes (or some other animal) will dig up nodes and potentially carry them off for tens or hundreds of meteres. Being sanitary with the rope handles (e.g. not getting food grease on them) seems to help, as well as spraying the nodes and handles with methylated spirits et al. when deploying. There are other specialized products available depending on your environment.
65		-
66	66	= **Installation** =
67	67
68		-(% class="box infomessage" %)
69		-(((
70		-**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
71		-)))
	26	+=== **1- Logbook documentation** ===
72	72
73		-== 1. Logbook documentation ==
74		-
75	75	(((
76		-**Essential Details** for field logs:
	29	+**Essential Details**: Record the following in a logbook:
77	77
78	78	* Station name
79		-* Latitude, longitude, elevation
	32	+* Latitude and longitude
80	80	* Names of team members present
81		-* Date and both local & UTC time of installation/removal
82		-* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
83		-* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
	34	+* Date and local time of installation
	35	+* Serial number (SN) of the sensor
	36	+* Detailed notes on the site conditions and setup
84	84
85		-[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
86		-
87		-== 2. Node Placement ==
	38	+=== **2- Node Placement** ===
88	88	)))
89	89
90		-**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
	41	+**Protection**: Place nodes inside thick, landfill biodegradable plastic bags for environmental protection.
91	91
92	92	**Site Analysis**:
93	93
94		-* **Take compass measurements away from the sensor as it will affect your measurement.**
95		-* Take photographs from various angles to document the site setup thoroughly.
96		-* Include a detailed site description in your notes
	45	+* Conduct compass measurements away from the node and metallic structures, adjusting for inclination angle.
	46	+* Take multiple photographs from various angles to document the site setup thoroughly.
	47	+* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
97	97
98		-== 3. GPS Considerations ==
	49	+=== **3- GPS Considerations** ===
99	99
100	100	(% class="wikigeneratedid" %)
101		-The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
	52	+The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
102	102
103		-== 4. Visibility and Location Marking ==
	54	+=== **4- Visibility and Location Marking** ===
104	104
105	105	**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
106	106
...	...	@@ -109,50 +109,61 @@
109	109	* Use a GPS device to mark the instrument's exact location.
110	110	* Record this location in both your paper notes and the GPS device.
111	111
112		-== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5. Charge Time, Pre-Deployment & Post-Deployment(%%) ==
	63	+=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5- Charge Time, Pre-Deployment & Post-Deployment**(%%) ===
113	113
114	114	* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
115	115	* **Pre-Deployment Charging**:
116		-** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
	67	+** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge right before deployment.
117	117
118	118	* **Operational Duration**:
119		-** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
	70	+** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle.
120	120
121	121	* **Post-Retrieval Charging**:
122		-** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
	73	+** Do not store the instruments with completely drained batteries.
	74	+** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) for optimal battery health.
	75	+
123	123	* **Storage and Shipping Charge Level**:
124		-** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
	77	+** Maintain a battery charge level of around 50-60% for both storage and shipping purposes.
125	125	** This charge level is recommended to prevent battery damage and is safe for transportation.
126		-** Nodes should not be stored fully charged, and **they should especially not be stored with 0 charge as this damages lithium batteries.**
127	127
128		-(((
129		-== 6. Data Sharing and Metadata Creation ==
130		-)))
	80	+=== ===
131	131
	82	+=== **6- Data Sharing and Metadata Creation** ===
	83	+
132	132	**GPS Data**:
133	133
134		-* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
	86	+* Download the GPS file to a laptop.
	87	+* Share this file on a drive accessible to all team members for uniform understanding of node locations.
135	135
136	136	**Photo Sharing**:
137	137
138		-* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
	91	+* Upload site photos to a shared platform (OneDrive, Dropbox, etc.).
	92	+* Integrating photos into Google Maps or Google Earth can be particularly beneficial for easy location referencing.
139	139
140	140	**Metadata File**:
141	141
142		-* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.
	96	+* Create a metadata XML file for each node, which is essential for data organisation and future reference.
143	143
144		-== 7. Additional Best Practices ==
	98	+=== **7- Additional Best Practices** ===
145	145
146		-* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
	100	+* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
	101	+* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass, and other equipment to ensure consistent and accurate data collection.
147	147
148		-----
	103	+* (((
	104	+==== **Keeping the Instruments Clean** ====
	105	+)))
	106	+* (((
	107	+Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
	108	+)))
149	149
150		-= **Seismic Station Demobilization and Documentation** =
	110	+= =
151	151
	112	+=== **Seismic Station Demobilization and Documentation** ===
	113	+
152	152	1. (((
153	153	**Preparation for Demobilization**:
154	154
155		-* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
	117	+* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, clipboard, logbook, and compass ready in your tote bag.
156	156	)))
157	157	1. (((
158	158	**Locating the instrument**:
...	...	@@ -164,7 +164,7 @@
164	164	1. (((
165	165	**Labeling Instruments for Demobilization**:
166	166
167		-* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
	129	+* Write the station name and the instrument’s serial number on a label.
168	168	* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
169	169	* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
170	170	)))
...	...	@@ -185,387 +185,263 @@
185	185
186	186	* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
187	187	* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
188		-
189		-
190	190	)))
191	191
192		-[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
193	193
194		-----
195	195
196		-= **Charging Procedure for Seismic Nodes** =
197	197
198		-(((
199		-== 1. Preparation for Charging: ==
200	200
201		-* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
202		-)))
203	203
204		-(((
205		-== 2. Disassembling the Node: ==
206	206
207		-* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
208		-)))
209	209
210		-(((
211		-== 3. Setting Nodes in the Charging Box: ==
212	212
213		-* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
214		-)))
215	215
216		-(((
217		-== 4. Monitoring the Charging Process: ==
218	218
219		-* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
220		-* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
221		-)))
222	222
223		-(((
224		-== 5. Updating Charge Status: ==
225	225
226		-* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
227		-* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
228		-)))
229	229
230		-[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
231	231
	166	+= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
232	232
	168	+blahblah
233	233
	170	+== Sub-paragraph ==
234	234
235		-{{{
236		- }}}
237	237
238		-----
	173	+== ==
239	239
240		-= **Downloading and Converting Seismic Data to MiniSeed Format** =
241	241
242		-(% class="wikigeneratedid" %)
243		-SmartSolo provides the following powerpoint for SmartSolo node programming and operation. Note that ANSIR only uses a portion of their process for our own uses: [[https:~~/~~/nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf>>url:https://nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf]]
	176	+= Smart Solo BD3C-5 (5 second) Broad-Band Node =
244	244
245		-== Connection tips: ==
	178	+Lorem
246	246
247		-Connecting SmartSolo nodes to their harvesters and having SoloLite recognise them can be a bit tricky, here are some tricks to help register and program them easier:
	180	+[[image:1705196270090-364.png]]
248	248
249		-* Place the node on the harvester gently, then firmly press it down onto the pins.
250		-* Place all nodes onto the harvester before trying any troubleshooting, as they may not show up while the SoloLite software is running. Once all are connected, try restarting the software for them to be recognised.
251		-* If a node is refusing to connect, try it with another slot. It is easiest if you place all 16 nodes on the harvester, and swap any nodes that refuse to connect with each other.
252		-* Nodes will likely not show up in the order that they should, though this is not an issue. E.g, a node in slot 6 on the harvester may show up in port 13 in the SoloLite software. Annoying, but it doesn't matter so long as you keep track of what's been harvested!
253	253
	183	+== GPS Considerations ==
254	254
	185	+The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
255	255
256		-== Node Registration and Software Setup ==
	187	+= Keeping the Instruments Clean =
257	257
258		-1. (((
259		-**Registering Nodes in the System**:
	189	+Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
260	260
261		-* To begin, register the nodes in the system so the software can recognize them.
262		-* Navigate to the installation folder of “SmartSoloApps SoloLite”.
263		-* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
264		-* To avoid double registration, replace the file each time you register a new node.
265		-)))
266		-1. (((
267		-**Creating a New Project in SoloLite**:
268	268
269		-* Open the “SoloLite” software.
270		-* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
271		-* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
272		-)))
	192	+= Charge Time, Instrument Life, and Charge During Storage & Shipping =
273	273
274		-== File structure ==
	194	+Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
275	275
276		-There are essentially three main folders where relevant PROSPECT and PROJECT DATA is stored. Individual projects will be found as subfolders in these.
	196	+Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
277	277
278		-=== SOLOLITE ===
279	279
280		-This folder stores SoloLite config files and parameters. Nothing too important stored here, you can always start over and re-create this.
	199	+= Best Practices and Guide =
281	281
282		-=== DCCDATA ===
	201	+== Install ==
283	283
284		-This folder stores the RAW data you have harvested from the nodes. The data will still be on the nodes (unless you erased it) in case of emergency, but regardless, this is the folder you want to back up and save somewhere.
	203	+Logbook is required (used again for pick up & metadata creation)
285	285
286		-If you had a weird time harvesting a node, you can always manually copy it as if it were a USB stick and place it into this folder manually. The structure is: //C:/DCCDATA/prospect_name/project_name/SERIALNUMBER/label(usually a timestamp but can be anything)//
	205	+- station name
287	287
288		-Then in the SoloLite software, go to tools > Reanalyze Seismic Data
	207	+- lat / long
289	289
290		-=== SOLODATA ===
	209	+- team members
291	291
292		-This folder stores **exported** (e.g. miniseed) data. It is structured similarly. If your DCCDATA is intact, this can always be re-created if need be.
	211	+- date and local time
293	293
	213	+- SN of sensor
294	294
295		-== Data Downloading Process ==
	215	+- notes on site
296	296
297		-1. (((
298		-**Initiating Data Download**:
	217	+Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
299	299
300		-* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
301		-* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
302		-* Select all nodes and right-click to “force download”. This starts the download process.
303		-* Completed downloads will appear as new folders in the Downloaded Data panel.
304		-)))
305		-1. (((
306		-**Exporting Data in Readable Format**:
	219	+Take compass measurement away from node and fences [make sure to adjust inclination angle]
307	307
308		-* Go to the “Tool” menu and select “export seismic data”.
309		-* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
310		-* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
311		-* (% class="box warningmessage" %)
312		-(((
313		-* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**
	221	+Take many photos from the site from different angles
314	314
315		-* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**
316		-)))
317		-)))
	223	+Add a precise site description to the notes such as distances and orientations from landmarks
318	318
319		-== Smart Solo Z Polarity bug (SP nodes ONLY!) ==
	225	+It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
320	320
321		-See [[https:~~/~~/auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug>>https://auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug]] for discussion. If data is headed to AusPass, we prefer to invert the IGU-16HR 3 Z channel data manually rather than in the SoloLite software or inverting the response metadata. **The BD3C-5 data does not require a polarity inversion.**
	227	+Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
322	322
323		-== 18 Leap Second bug ==
	229	+Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
324	324
325		-Not so much a bug as much as "a thing that can happen if your SoloLite installation is corrupted". If you notice your data has large time offsets, you should suspect that the number of leap seconds has not been accounted properly. There is a file "smartsoloconfig.xml" that needs to be present in "C:\SmartSoloApps SoloLite" (e.g. the main program directory) that dictates the leap second offset for the last two data ranges. Since 2017-01-01, this is 18 seconds.
	231	+Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
326	326
327		-If this file is missing, just create a new one structured like so, name it "smartsoloconfig.xml" and put it in your main program directory. Then, Reanalyze your data (tools > Reanalyze seismic data) and your data should have the correct time. You can also do this manually, if you want. The offset is 18 seconds precisely.
	233	+Create metadata .xml file
328	328
329		-{{code language="none"}}
330		-<?xml version="1.0" encoding="UTF-8"?>
331		-<config>
332		- <leapsecond>
333		- <interval>
334		- <start_time>2017-01-01#00:00:00</start_time>
335		- <end_time>2999-12-31#23:59:59</end_time>
336		- <second>18</second>
337		- </interval>
338		- <interval>
339		- <start_time>1970-01-01#00:00:00</start_time>
340		- <end_time>2017-01-01#00:00:00</end_time>
341		- <second>17</second>
342		- </interval>
343		- </leapsecond>
344		- <GPS_distance_threshold_degree>
345		- 4e-5
346		- </GPS_distance_threshold_degree>
347		-</config>
348		-{{/code}}
349	349
	236	+== Removing/Demob ==
350	350
351		-== Handling Nodes During Download ==
	238	+Download and then use the GPS file to locate the node
352	352
353		-1. (((
354		-**Monitoring Download Indicators**:
	240	+Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.
355	355
356		-* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
357		-* Disconnect nodes properly before unplugging anything.
358		-* Be cautious: if the laptop enters sleep mode, the download will pause.
359		-)))
360		-1. (((
361		-//**Investment in Storage Hardware**~://
362	362
363		-* (% class="box warningmessage" %)
364		-(((
365		-* **Use fast external hard drives to avoid limitations in data harvesting.**
	243	+Upload photos of the site
366	366
367		-* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
368		-* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
369		-)))
370		-)))
371		-1. (((
372		-**Metadata and Time Settings**:
	245	+- station name
373	373
374		-* Ensure all metadata is saved with the file.
375		-* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
376		-)))
377		-1. (((
378		-**Finalizing the Download**:
	247	+- latitude
379	379
380		-* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
	249	+- longitude
381	381
382		-
383		-)))
	251	+- elevation
384	384
385		-[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
	253	+* SN of sensor – SN of battery (optional)
	254	+* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
386	386
	256	+Upload photos into Google Earth and on a shared drive
387	387
	258	+Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!).
388	388
389		-[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
	260	+Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
390	390
	262	+Take a photo of the entire setup node with the label on it + compass
391	391
	264	+Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
392	392
393	393
394		-[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
	267	+== Charging ==
395	395
	269	+Clean node prior to charging and harvesting the data
396	396
	271	+Remove battery (and spike) from the sensor by twisting the spike part of the instrument
397	397
398		-[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
	273	+Set 16 nodes into the charging box (spikes up)
399	399
	275	+Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
400	400
	277	+This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
401	401
402		-[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
	279	+[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
403	403
404		-----
405	405
406		-= **Cleaning** =
407	407
408		-When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
	283	+== Downloading and Converting Data to MiniSeed ==
409	409
410		-= **Weights (for shipping)** =
411	411
412		-The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
	286	+The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
413	413
414		-1 bag + 6 SP (IGU-16HR) nodes: 18 kg
	288	+[[image:1705195543887-977.png]]
415	415
416		-1 SP (IGU-16HR) data harvester: 21.5 kg
417	417
418		-1 SP (IGU-16HR) charger: 26.3 kg
	291	+Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
419	419
420		-1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
	293	+[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
421	421
422		-1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
423		-)))
424	424
425		-(% class="col-xs-12 col-sm-4" %)
426		-(((
427		-(% class="box" %)
428		-(((
429		-**Contents**
	296	+Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
430	430
431		-{{toc/}}
	298	+[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
432	432
433		-
434		-)))
	300	+At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
435	435
436		-(% class="box" %)
	302	+(% class="box warningmessage" %)
437	437	(((
438		-= SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
439		-
440		-[[image:Smartsolo IGU BD3C 5 (2).jpg]]
441		-
442		-[[image:smartsolo.jpg]]
443		-
444		-|(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
445		-|(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
446		-|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)Φ158 x160mm(H)
447		-|(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
448		-|(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
449		-|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
450		-Lithium-ion battery contained in equipment (168.84 Wh)
451		-
452		-UN3481 PI967 S1
	304	+**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
453	453	)))
454		-)))
455	455
456		-(% class="box" %)
	307	+(% class="box warningmessage" %)
457	457	(((
458		-= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
	309	+**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
	310	+)))
459	459
460		-[[image:smartsolo node.jpg]]
	312	+A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
461	461
462		-[[image:smartsolo node 2.jpg]]
	314	+Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
463	463
464		-|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
465		-|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)76.7 V/m/s
466		-|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm(H)
467		-|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
468		-|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
469		-|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
470		-Lithium-ion battery contained in equipment (96.48 Wh)
	316	+[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
471	471
472		-UN3481 PI967 S2
473		-)))
474		-)))
	318	+When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
475	475
476		-(% class="box" %)
	320	+(% class="box infomessage" %)
477	477	(((
478		-
	322	+**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
	323	+)))
479	479
480		-= SmartSolo [[IGU-16>>url:https://smartsolo.com/cp-3.html]]1C =
	325	+When downloading, ensure that all metadata is saved along with the file.
481	481
	327	+Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
482	482
483		-[[image:Screenshot 2025-08-01 161027.png]]
	329	+//Once downloaded, mark the "D" box on your temporary labels!//
484	484
485		-|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 413Hz
486		-|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)80 V/m/s
487		-|(% style="width:187px" %)**Size (without spike)**|(% style="width:224px" %)95mm(L) × 103mm(W) × 118mm(H)
488		-|(% style="width:187px" %)**Weight**|(% style="width:224px" %)1.1 kg
489		-|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)8 Gb
490		-|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
491		-Lithium-ion battery contained in equipment (38.48 Wh)
	331	+== Converting data ==
492	492
493		-UN3481 PI967 S2
494		-)))
495		-)))
	333	+Check the data all have been converted to miniseed correctly
496	496
497		-(% class="box" %)
498		-(((
499		-= SmartSolo BD3C-16 Portable Battery Charger =
	335	+– 3 files per station per day
500	500
501		-[[image:20250729_125049.jpg]]
	337	+* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
	338	+* ~~ 5 Gb / node / month
502	502
503		-|**Dimensions (LxHxW)**|558 x 357 x 300mm
504		-|**Input rating**|100-210V - 50/60Hz
505		-|**Power**|1000W
506		-|**Weight**|14.5kg
507		-|**Weight with cables**|21kg
508		-)))
	340	+//Tick ‘R’ box on the node label//
509	509
510		-(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
511		-(((
512		-= SmartSolo IGU-16 Portable Data Harvester =
513	513
514		-[[image:20250729_124747.jpg]]
	343	+== Cleaning ==
515	515
516		-|**Dimensions (LxHxW)**|625 x 500 x 366mm
517		-|**Input rating**|100-210V - 50/60Hz
518		-|**Power**|100W
519		-|**Weight**|21.5 - 24kg
520		-|**Slots no.**|16
521		-|**Download Speed**|20MB/sec/slot
	345	+If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
	346	+
	347	+
522	522	)))
523	523
	350	+
	351	+(% class="col-xs-12 col-sm-4" %)
	352	+(((
524	524	(% class="box" %)
525	525	(((
526		-= SmartSolo IGU-16 Portable Battery Charger =
	355	+**Contents**
527	527
528		-[[image:20250729_124644.jpg]]
529		-
530		-|**Dimensions (LxHxW)**|625 x 500 x 366mm
531		-|**Input rating**|100-210V - 50/60Hz
532		-|**Power**|640W
533		-|**Weight**|26.3kg
534		-|**Slots no.**|16
	357	+(% class="wikitoc" %)
	358	+* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
	359	+** [[Sub-paragraph>>path:#HSub-paragraph]]
	360	+** [[ >>path:#H]]
	361	+* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
	362	+** [[GPS Considerations>>path:#HGPSConsiderations]]
	363	+* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
	364	+* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
	365	+* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
	366	+** [[Install>>path:#HInstall]]
	367	+** [[Removing/Demob>>path:#HRemoving2FDemob]]
	368	+** [[Charging>>path:#HCharging]]
	369	+** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
	370	+** [[Converting data>>path:#HConvertingdata]]
	371	+** [[Cleaning>>path:#HCleaning]]
535	535	)))
536	536
	374	+
537	537	(% class="box" %)
538	538	(((
539		-= SmartSolo BD3C-5 Carry Case =
	377	+= SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
540	540
541		-[[image:20250729_124957.jpg]]
	379	+[[image:Smartsolo IGU BD3C 5 (2).jpg]]
542	542
	381	+[[image:smartsolo.jpg]]
543	543
544		-|**Dimensions (LxHxW)**|590 x 225 x 405mm
545		-|**Weight**|8.2kg
546		-|**Slots no.**|6
	383	+|(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
	384	+|(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
	385	+|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
	386	+|(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
	387	+|(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
	388	+|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
547	547	)))
548	548
549	549	(% class="box" %)
550	550	(((
551		-= SmartSolo IGU-16 3C Carry Bag =
	393	+= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
552	552
553		-[[image:20250729_124502.jpg]]
	395	+[[image:smartsolo node.jpg]]
554	554
555		-|**Dimensions (LxHxW)**|230 x 340 x 310mm
556		-|**Weight**|3.6kg
557		-|**Slots no.**|6
	397	+[[image:smartsolo node 2.jpg]]
	398	+
	399	+|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
	400	+|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
	401	+|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
	402	+|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.3 kg
	403	+|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
	404	+|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
558	558	)))
559	559
560		-(% class="box" %)
561		-(((
562		-= SmartSolo IGU-16 1C Carry Bag =
563		-
564		-[[image:20250729_124558.jpg]]
565		-
566		-|**Dimensions (LxHxW)**|225 x 200 x 550mm
567		-|**Weight**|
568		-|**Slots no.**|6
	407	+
569	569	)))
570	570	)))
571		-)))

1706153266647-145.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.sima

Size

...	...	@@ -1,1 +1,0 @@
1		-1.7 MB

Content

1706153354750-415.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.sima

Size

...	...	@@ -1,1 +1,0 @@
1		-2.1 MB

Content

1706153556166-231.jpeg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.sima

Size

...	...	@@ -1,1 +1,0 @@
1		-839.4 KB

Content

20250729_124502.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-318.3 KB

Content

20250729_124558.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-376.8 KB

Content

20250729_124644.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-528.0 KB

Content

20250729_124747.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-488.5 KB

Content

20250729_124957.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-532.5 KB

Content

20250729_125049.jpg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-457.6 KB

Content

BB_programming.labels.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.robert

Size

...	...	@@ -1,1 +1,0 @@
1		-111.5 KB

Content

SP_programming.labels.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.robert

Size

...	...	@@ -1,1 +1,0 @@
1		-106.7 KB

Content

Screenshot 2025-08-01 161027.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.JackD

Size

...	...	@@ -1,1 +1,0 @@
1		-82.8 KB

Content

example_metadata.txt

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.robert

Size

...	...	@@ -1,1 +1,0 @@
1		-2.7 KB

Content

...	...	@@ -1,46 +1,0 @@
1		-# AKL-HR Node Array (AHNA) code X5
2		-CITE: Name, Name, and Name. (2023). A Node Array [Data set]. International Federation of Digital Seismograph Networks. https://doi.org/10.7914/8jxr-7029
3		-
4		-#SITE START END LAT LONG ELEV SPS RECORDER S/N SENSOR S/N PROPERTY,LOCALITY,COUNTRY COMMENTS
5		-
6		-# INSTALL
7		-AKL01 20-05-2023T00:00 30-06-2023T00:00 -37.0471 175.5245 75 250 SSNODE_C 590001950 SSNODE_5S 590001950 "Te Puru,Hauraki,NZ"
8		-AKL02 20-05-2023T00:00 30-06-2023T00:00 -36.7476 175.5026 70 250 SSNODE_C 590001943 SSNODE_5S 590001943 "Coromandel Town,Hauraki,NZ"
9		-AKL03 20-05-2023T00:00 30-06-2023T00:00 -36.9694 175.5020 98 250 SSNODE_C 590002068 SSNODE_5S 590002068 "Te Mata,Hauraki,NZ"
10		-AKL05 19-05-2023T19:00 22-02-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001957 SSNODE_5S 590001957 "South Head South,Auckland,NZ" "site was disturbed"
11		-AKL06 19-05-2023T19:00 30-06-2023T00:00 -37.2459 175.3426 34 250 SSNODE_C 590001930 SSNODE_5S 590001930 "Back Miranda,Auckland,NZ"
12		-AKB05 02-05-2023T00:37 30-06-2023T00:00 -36.6651 175.4800 63 250 TSAWR TS085A TRILL120 4875 "Colville,Hauraki,NZ"
13		-
14		-# SERVICE 1
15		-AKL05 22-02-2023T00:00 30-06-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001999 SSNODE_.2S 590001999 "South Head South,Auckland,NZ" "swapped node to shortperiod"
16		-
17		-
18		-
19		-
20		-################### ANY LINE BEGINNING WITH # will be commented! Comments are good!
21		-
22		-
23		-# NOTES
24		-# the start/end time is not critical, but good to have. what IS critical are the times of instrument changes as this potentially affects response information
25		-# to mark equipment changes, add a new line with an updated start date (e.g. AKL05 above)
26		-# can use tabs or spaces, but spaces tend to look nicer. formatting ultimately doesn't matter too much so long as there is any sort of "white space" between the fields
27		-# if you don't know a serial number, put 999. if you don't know the elevation, put 0
28		-# for Nodes, put the same serial number for both Recoder and Sensor (since they are the same!)
29		-
30		-
31		-# EXAMPLE INSTRUMENT LABELS
32		-#LPR200 = ANU LPR-200 logger (beige box)
33		-#TSAWR = ANU TerraSAWR logger (yellow box)
34		-
35		-#TRILL120 = Trillium Compact 120s
36		-#TRILL20 = Trillium Compact 20s
37		-#TRILL120PH = Trillium Compact 120s PostHole
38		-#CMG6TD = Guralp 6TD
39		-#CMG3ESP = Guralp 3ESP
40		-#3DLITE = Lenarrtz 3D-LITE
41		-
42		-#SSNODE_C = output was in COUNTS (there is also SSNODE_MV, if you (accidentally!) output to millivolts etc)
43		-#SSNODE_5S = broadband (can also use SSNODE_BB)
44		-#SSNODE_.2S = shortperiod (can also use SSNODE_SP)
45		-
46		-#it doesn't matter too much what you use for equipment labels, so long as they are consistent and otherwise defined somewhere in the comments!

XWiki.XWikiRights[0]

Allow/Deny

...	...	@@ -1,1 +1,0 @@
1		-Allow

Groups

...	...	@@ -1,1 +1,0 @@
1		-XWiki.XWikiAllGroup

Levels

...	...	@@ -1,1 +1,0 @@
1		-comment

XWiki.XWikiRights[1]

Allow/Deny

...	...	@@ -1,1 +1,0 @@
1		-Allow

Levels

...	...	@@ -1,1 +1,0 @@
1		-comment

Users

...	...	@@ -1,1 +1,0 @@
1		-XWiki.XWikiGuest