Skip to Content
Last modified by KB on 2025/12/04 12:33
From version 85.1
edited by Jack Dent
on 2025/09/29 12:55
Change comment: There is no comment for this version
To version 13.2
edited by robert
on 2024/01/14 13:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SmartSolo Node Seismometers
1 +SmartSolo Nodes
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.JackD
1 +XWiki.robert
Content
... ... @@ -2,376 +2,191 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -= **Node Types** =
5 += SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
6 6  
7 -ANSIR carry two types of three-channel nodes, and one type of one-channel node:
7 +blahblah
8 8  
9 -* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 -* **SmartSolo BD3C-5 (5 Second Broadband)**
11 -* **SmartSolo IGU 16 1C (5 Hz Short Period, single channel)**
9 +== Sub-paragraph ==
12 12  
13 -The three-channel nodes have a battery capacity of ~~30 days, whereas the single-channel type has a capacity of ~~50 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
14 14  
15 -----
12 +== ==
16 16  
17 -= **Programming Defaults** =
18 18  
19 -SmartSolo provides the following powerpoint for SmartSolo node programming and operation. Note that ANSIR only uses a portion of their process for our own uses: [[https:~~/~~/nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf>>https://nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf]]
15 += Smart Solo BD3C-5 (5 second) Broad-Band Node =
20 20  
21 -The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.
17 +Lorem
22 22  
23 -[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]
19 +[[image:/xwiki/bin/download/Instrumentation/SmartSolo%20Nodes/WebHome/1705196270090-364.png?rev=1.1||alt="1705196270090-364.png"]]
24 24  
25 -[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]
26 26  
27 -FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
22 +== GPS Considerations ==
28 28  
29 -Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
24 +The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
30 30  
31 -Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
26 += Keeping the Instruments Clean =
32 32  
33 -If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
28 +Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
34 34  
35 -In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
36 36  
37 -Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
31 += Charge Time, Instrument Life, and Charge During Storage & Shipping =
38 38  
39 -GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
33 +Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
40 40  
41 -Bluetooth (BB nodes only) should be turned OFF to conserve power.
35 +Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
42 42  
43 -We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
44 44  
45 -{{info}}
46 -**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
47 -{{/info}}
38 += Best Practices and Guide =
48 48  
49 -=== **Programming tips**: ===
40 +== Install ==
50 50  
51 -Connecting SmartSolo nodes to their harvesters and having SoloLite recognise them can be a bit tricky, here are some tricks to help register and program them easier:
42 +Logbook is required (used again for pick up & metadata creation)
52 52  
53 - - Place the node on the harvester gently, then firmly press it down onto the pins
44 +- station name
54 54  
55 - - Place all nodes onto the harvester before trying any troubleshooting, as they may not show up while the SoloLite software is running. Once all are connected, try  restarting the software for them to be recognised.
46 +- lat / long
56 56  
57 - - If a node is refusing to connect, try it with another slot. It is easiest if you place all 16 nodes on the harvester, and swap any nodes that refuse to connect with eachother
48 +- team members
58 58  
59 - - Nodes will likely not show up in the order that they should, though this is not an issue. Eg, a node in slot 6 on the harvester may show up in port 13 in the SoloLite software
50 +- date and local time
60 60  
61 -= **Fieldwork Preparation** =
52 +- SN of sensor
62 62  
63 -(% class="box warningmessage" %)
64 -(((
65 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
54 +- notes on site
66 66  
67 -**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
56 +Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
68 68  
69 -**We have had good experience with the 4Tb Samsung T7 Shield drives.**
70 -)))
58 +Take compass measurement away from node and fences [make sure to adjust inclination angle]
71 71  
72 -== Magnets ==
60 +Take many photos from the site from different angles 
73 73  
74 -If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).
62 +Add a precise site description to the notes such as distances and orientations from landmarks 
75 75  
76 -== Animal-Proofing ==
64 +It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
77 77  
78 -We have experienced times where foxes (or some other animal) will dig up nodes and potentially carry them off for tens or hundreds of meteres. Being sanitary with the rope handles (e.g. not getting food grease on them) seems to help, as well as spraying the nodes and handles with methylated spirits et al. when deploying. There are other specialized products available depending on your environment.
66 +Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
79 79  
80 -= **Installation** =
68 +Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
81 81  
82 -(% class="box infomessage" %)
83 -(((
84 -**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
85 -)))
70 +Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
86 86  
87 -== 1. Logbook documentation ==
72 +Create metadata .xml file
88 88  
89 -(((
90 -**Essential Details** for field logs:
91 91  
92 -* Station name
93 -* Latitude, longitude, elevation
94 -* Names of team members present
95 -* Date and both local & UTC time of installation/removal
96 -* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
97 -* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
75 +== Removing/Demob ==
98 98  
99 -[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
77 +Download and then use the GPS file to locate the node 
100 100  
101 -== 2. Node Placement ==
102 -)))
79 +Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
103 103  
104 -**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
105 105  
106 -**Site Analysis**:
82 +Upload photos of the site  
107 107  
108 -* **Take compass measurements away from the sensor as it will affect your measurement.**
109 -* Take photographs from various angles to document the site setup thoroughly.
110 -* Include a detailed site description in your notes
84 +- station name
111 111  
112 -== 3. GPS Considerations ==
86 +- latitude
113 113  
114 -(% class="wikigeneratedid" %)
115 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
88 +- longitude
116 116  
117 -== 4. Visibility and Location Marking ==
90 +- elevation
118 118  
119 -**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
92 +* SN of sensor – SN of battery (optional)
93 +* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
120 120  
121 -**GPS Marking**:
95 +Upload photos into Google Earth and on a shared drive
122 122  
123 -* Use a GPS device to mark the instrument's exact location.
124 -* Record this location in both your paper notes and the GPS device.
97 +Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
125 125  
126 -== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5. Charge Time, Pre-Deployment & Post-Deployment(%%) ==
99 +Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
127 127  
128 -* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
129 -* **Pre-Deployment Charging**:
130 -** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
101 +Take a photo of the entire setup node with the label on it + compass 
131 131  
132 -* **Operational Duration**:
133 -** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
103 +Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
134 134  
135 -* **Post-Retrieval Charging**:
136 -** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
137 -* **Storage and Shipping Charge Level**:
138 -** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
139 -** This charge level is recommended to prevent battery damage and is safe for transportation.
140 -** Nodes should not be stored fully charged, and **they should especially not be stored with 0 charge as this damages lithium batteries.**
141 141  
142 -(((
143 -== 6. Data Sharing and Metadata Creation ==
144 -)))
106 +== Charging ==
145 145  
146 -**GPS Data**:
108 +Clean node prior to charging and harvesting the data
147 147  
148 -* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
110 +Remove battery (and spike) from the sensor by twisting the spike part of the instrument
149 149  
150 -**Photo Sharing**:
112 +Set 16 nodes into the charging box (spikes up)
151 151  
152 -* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
114 +Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
153 153  
154 -**Metadata File**:
116 +This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
155 155  
156 -* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.
118 +[[IGU 16-HRcharger (left) and harvester (right)>>image:/xwiki/bin/download/Instrumentation/SmartSolo%20Nodes/WebHome/1705195933422-337.png?rev=1.1||alt="1705195933422-337.png" data-xwiki-image-style-alignment="center"]]
157 157  
158 -== 7. Additional Best Practices ==
159 159  
160 -* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
161 161  
162 -----
122 +== Downloading and Converting Data to MiniSeed ==
163 163  
164 -= **Seismic Station Demobilization and Documentation** =
165 165  
166 -1. (((
167 -**Preparation for Demobilization**:
125 +The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
168 168  
169 -* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
170 -)))
171 -1. (((
172 -**Locating the instrument**:
127 +[[image:/xwiki/bin/download/Instrumentation/SmartSolo%20Nodes/WebHome/1705195543887-977.png?rev=1.1||alt="1705195543887-977.png"]]
173 173  
174 -* Use the downloaded GPS file to accurately locate the node for demobilization.
175 -* Import this KMZ file onto your phone for easy reference and location tracking.
176 -* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
177 -)))
178 -1. (((
179 -**Labeling Instruments for Demobilization**:
180 180  
181 -* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
182 -* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
183 -* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
184 -)))
185 -1. (((
186 -**Photographing the Setup Node**:
130 +Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
187 187  
188 -* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
189 -* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
190 -)))
191 -1. (((
192 -**Logging Demobilization Details**:
132 +[[image:/xwiki/bin/download/Instrumentation/SmartSolo%20Nodes/WebHome/1705195543890-537.png?rev=1.1||alt="1705195543890-537.png" data-xwiki-image-style-alignment="center"]]
193 193  
194 -* Use the field logbook to note the time of demobilization, serial numbers, and station name.
195 -* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
196 -)))
197 -1. (((
198 -**Final Checks and Equipment Removal**:
199 199  
200 -* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
201 -* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
135 +Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
202 202  
203 -
204 -)))
137 +[[image:/xwiki/bin/download/Instrumentation/SmartSolo%20Nodes/WebHome/1705195543891-334.png?rev=1.1||alt="1705195543891-334.png" data-xwiki-image-style-alignment="center"]]
205 205  
206 -[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
139 +At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
207 207  
208 -----
209 -
210 -= **Charging Procedure for Seismic Nodes** =
211 -
141 +(% class="box warningmessage" %)
212 212  (((
213 -== 1. Preparation for Charging: ==
214 -
215 -* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
143 +**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
216 216  )))
217 217  
146 +(% class="box warningmessage" %)
218 218  (((
219 -== 2. Disassembling the Node: ==
220 -
221 -* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
148 +**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
222 222  )))
223 223  
224 -(((
225 -== 3. Setting Nodes in the Charging Box: ==
151 +A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
226 226  
227 -* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
228 -)))
153 +Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
229 229  
230 -(((
231 -== 4. Monitoring the Charging Process: ==
155 +[[image:/xwiki/bin/download/Instrumentation/SmartSolo%20Nodes/WebHome/1705195543898-365.png?rev=1.1||alt="1705195543898-365.png" data-xwiki-image-style-alignment="center"]]
232 232  
233 -* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
234 -* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
235 -)))
157 +When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
236 236  
159 +(% class="box infomessage" %)
237 237  (((
238 -== 5. Updating Charge Status: ==
239 -
240 -* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
241 -* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
161 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
242 242  )))
243 243  
244 -[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
164 +When downloading, ensure that all metadata is saved along with the file.
245 245  
166 +Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
246 246  
168 +//Once downloaded, mark the "D" box on your temporary labels!//
247 247  
170 +== Converting data ==
248 248  
249 -[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
172 +Check the data all have been converted to miniseed correctly 
250 250  
251 -----
174 +– 3 files per station per day 
252 252  
253 -= **Downloading and Converting Seismic Data to MiniSeed Format** =
176 +* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
177 +* ~~ 5 Gb / node / month
254 254  
255 -== Node Registration and Software Setup ==
179 +//Tick ‘R’ box on the node label//
256 256  
257 -1. (((
258 -**Registering Nodes in the System**:
259 259  
260 -* To begin, register the nodes in the system so the software can recognize them.
261 -* Navigate to the installation folder of “SmartSoloApps SoloLite”.
262 -* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
263 -* To avoid double registration, replace the file each time you register a new node.
264 -)))
265 -1. (((
266 -**Creating a New Project in SoloLite**:
182 +== Cleaning ==
267 267  
268 -* Open the “SoloLite” software.
269 -* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
270 -* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
271 -)))
184 +If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
272 272  
273 -== Data Downloading Process ==
274 -
275 -1. (((
276 -**Initiating Data Download**:
277 -
278 -* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
279 -* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
280 -* Select all nodes and right-click to “force download”. This starts the download process.
281 -* Completed downloads will appear as new folders in the Downloaded Data panel.
282 -)))
283 -1. (((
284 -**Exporting Data in Readable Format**:
285 -
286 -* Go to the “Tool” menu and select “export seismic data”.
287 -* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
288 -* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
289 -* (% class="box warningmessage" %)
290 -(((
291 -* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**
292 -
293 -* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**
294 -)))
295 -)))
296 -
297 -== Smart Solo Z Polarity bug ==
298 -
299 -See [[https:~~/~~/auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug>>https://auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug]] for discussion. If data is headed to AusPass, we prefer to invert the IGU-16HR 3 Z channel data manually rather than invert the response metadata. The BD3C-5 data does not require a polarity inversion.
300 -
301 -== Handling Nodes During Download ==
302 -
303 -1. (((
304 -**Monitoring Download Indicators**:
305 -
306 -* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
307 -* Disconnect nodes properly before unplugging anything.
308 -* Be cautious: if the laptop enters sleep mode, the download will pause.
309 -)))
310 -1. (((
311 -//**Investment in Storage Hardware**~://
312 -
313 -* (% class="box warningmessage" %)
314 -(((
315 -* **Use fast external hard drives to avoid limitations in data harvesting.**
316 -
317 -* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
318 -* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
319 -)))
320 -)))
321 -1. (((
322 -**Metadata and Time Settings**:
323 -
324 -* Ensure all metadata is saved with the file.
325 -* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
326 -)))
327 -1. (((
328 -**Finalizing the Download**:
329 -
330 -* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
331 -
332 332  
333 333  )))
334 334  
335 -[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
336 336  
337 -
338 -
339 -[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
340 -
341 -
342 -
343 -
344 -[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
345 -
346 -
347 -
348 -[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
349 -
350 -
351 -
352 -[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
353 -
354 -----
355 -
356 -= **Cleaning** =
357 -
358 -When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
359 -
360 -= **Weights (for shipping)** =
361 -
362 -The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
363 -
364 -1 bag + 6 SP (IGU-16HR) nodes: 18 kg
365 -
366 -1 SP (IGU-16HR) data harvester: 21.5 kg
367 -
368 -1 SP (IGU-16HR) charger: 26.3 kg
369 -
370 -1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
371 -
372 -1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
373 -)))
374 -
375 375  (% class="col-xs-12 col-sm-4" %)
376 376  (((
377 377  (% class="box" %)
... ... @@ -378,144 +378,48 @@
378 378  (((
379 379  **Contents**
380 380  
381 -{{toc/}}
382 -
383 -
196 +(% class="wikitoc" %)
197 +* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
198 +** [[Sub-paragraph>>path:#HSub-paragraph]]
199 +** [[ >>path:#H]]
200 +* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
201 +** [[GPS Considerations>>path:#HGPSConsiderations]]
202 +* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
203 +* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
204 +* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
205 +** [[Install>>path:#HInstall]]
206 +** [[Removing/Demob>>path:#HRemoving2FDemob]]
207 +** [[Charging>>path:#HCharging]]
208 +** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
209 +** [[Converting data>>path:#HConvertingdata]]
210 +** [[Cleaning>>path:#HCleaning]]
384 384  )))
385 385  
213 +
386 386  (% class="box" %)
387 387  (((
388 388  = SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
389 389  
390 -[[image:Smartsolo IGU BD3C 5 (2).jpg]]
391 -
392 -[[image:smartsolo.jpg]]
393 -
394 394  |(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
395 395  |(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
396 -|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)Φ158 x160mm(H)
220 +|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
397 397  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
398 398  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
399 -|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
400 -Lithium-ion battery contained in equipment (168.84 Wh)
401 -
402 -UN3481 PI967 S1
223 +|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
403 403  )))
404 -)))
405 405  
406 406  (% class="box" %)
407 407  (((
408 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
228 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
409 409  
410 -[[image:smartsolo node.jpg]]
411 -
412 -[[image:smartsolo node 2.jpg]]
413 -
414 414  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
415 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)76.7 V/m/s
416 -|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm(H)
231 +|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
232 +|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
417 417  |(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
418 418  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
419 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
420 -Lithium-ion battery contained in equipment (96.48 Wh)
421 -
422 -UN3481 PI967 S2
235 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
423 423  )))
424 -)))
425 425  
426 -(% class="box" %)
427 -(((
428 428  
429 -
430 -= SmartSolo [[IGU-16>>url:https://smartsolo.com/cp-3.html]]1C =
431 -
432 -
433 -[[image:Screenshot 2025-08-01 161027.png]]
434 -
435 -|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 413Hz
436 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)80 V/m/s
437 -|(% style="width:187px" %)**Size (without spike)**|(% style="width:224px" %)95mm(L) × 103mm(W) × 118mm(H)
438 -|(% style="width:187px" %)**Weight**|(% style="width:224px" %)1.1 kg
439 -|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)8 Gb
440 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
441 -Lithium-ion battery contained in equipment (38.48 Wh)
442 -
443 -UN3481 PI967 S2
444 444  )))
445 445  )))
446 -
447 -(% class="box" %)
448 -(((
449 -= SmartSolo BD3C-16 Portable Battery Charger =
450 -
451 -[[image:20250729_125049.jpg]]
452 -
453 -|**Dimensions (LxHxW)**|558 x 357 x 300mm
454 -|**Input rating**|100-210V - 50/60Hz
455 -|**Power**|1000W
456 -|**Weight**|14.5kg
457 -|**Weight with cables**|21kg
458 -)))
459 -
460 -(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
461 -(((
462 -= SmartSolo IGU-16 Portable Data Harvester =
463 -
464 -[[image:20250729_124747.jpg]]
465 -
466 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
467 -|**Input rating**|100-210V - 50/60Hz
468 -|**Power**|100W
469 -|**Weight**|21.5 - 24kg
470 -|**Slots no.**|16
471 -|**Download Speed**|20MB/sec/slot
472 -)))
473 -
474 -(% class="box" %)
475 -(((
476 -= SmartSolo IGU-16 Portable Battery Charger =
477 -
478 -[[image:20250729_124644.jpg]]
479 -
480 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
481 -|**Input rating**|100-210V - 50/60Hz
482 -|**Power**|640W
483 -|**Weight**|26.3kg
484 -|**Slots no.**|16
485 -)))
486 -
487 -(% class="box" %)
488 -(((
489 -= SmartSolo BD3C-5 Carry Case =
490 -
491 -[[image:20250729_124957.jpg]]
492 -
493 -
494 -|**Dimensions (LxHxW)**|590 x 225 x 405mm
495 -|**Weight**|8.2kg
496 -|**Slots no.**|6
497 -)))
498 -
499 -(% class="box" %)
500 -(((
501 -= SmartSolo IGU-16 3C Carry Bag =
502 -
503 -[[image:20250729_124502.jpg]]
504 -
505 -|**Dimensions (LxHxW)**|230 x 340 x 310mm
506 -|**Weight**|3.6kg
507 -|**Slots no.**|6
508 -)))
509 -
510 -(% class="box" %)
511 -(((
512 -= SmartSolo IGU-16 1C Carry Bag =
513 -
514 -[[image:20250729_124558.jpg]]
515 -
516 -|**Dimensions (LxHxW)**|225 x 200 x 550mm
517 -|**Weight**|
518 -|**Slots no.**|6
519 -)))
520 -)))
521 -)))
1706153266647-145.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -839.4 KB
Content
20250729_124502.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -457.6 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -106.7 KB
Content
Screenshot 2025-08-01 161027.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -82.8 KB
Content
Smartsolo IGU BD3C 5 (2).jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -909.0 KB
Content
Smartsolo IGU BD3C 5.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -2.7 MB
Content
example_metadata.txt
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -2.7 KB
Content
... ... @@ -1,46 +1,0 @@
1 -# AKL-HR Node Array (AHNA) code X5
2 -CITE: Name, Name, and Name. (2023). A Node Array [Data set]. International Federation of Digital Seismograph Networks. https://doi.org/10.7914/8jxr-7029
3 -
4 -#SITE START END LAT LONG ELEV SPS RECORDER S/N SENSOR S/N PROPERTY,LOCALITY,COUNTRY COMMENTS
5 -
6 -# INSTALL
7 -AKL01 20-05-2023T00:00 30-06-2023T00:00 -37.0471 175.5245 75 250 SSNODE_C 590001950 SSNODE_5S 590001950 "Te Puru,Hauraki,NZ"
8 -AKL02 20-05-2023T00:00 30-06-2023T00:00 -36.7476 175.5026 70 250 SSNODE_C 590001943 SSNODE_5S 590001943 "Coromandel Town,Hauraki,NZ"
9 -AKL03 20-05-2023T00:00 30-06-2023T00:00 -36.9694 175.5020 98 250 SSNODE_C 590002068 SSNODE_5S 590002068 "Te Mata,Hauraki,NZ"
10 -AKL05 19-05-2023T19:00 22-02-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001957 SSNODE_5S 590001957 "South Head South,Auckland,NZ" "site was disturbed"
11 -AKL06 19-05-2023T19:00 30-06-2023T00:00 -37.2459 175.3426 34 250 SSNODE_C 590001930 SSNODE_5S 590001930 "Back Miranda,Auckland,NZ"
12 -AKB05 02-05-2023T00:37 30-06-2023T00:00 -36.6651 175.4800 63 250 TSAWR TS085A TRILL120 4875 "Colville,Hauraki,NZ"
13 -
14 -# SERVICE 1
15 -AKL05 22-02-2023T00:00 30-06-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001999 SSNODE_.2S 590001999 "South Head South,Auckland,NZ" "swapped node to shortperiod"
16 -
17 -
18 -
19 -
20 -################### ANY LINE BEGINNING WITH # will be commented! Comments are good!
21 -
22 -
23 -# NOTES
24 -# the start/end time is not critical, but good to have. what IS critical are the times of instrument changes as this potentially affects response information
25 -# to mark equipment changes, add a new line with an updated start date (e.g. AKL05 above)
26 -# can use tabs or spaces, but spaces tend to look nicer. formatting ultimately doesn't matter too much so long as there is any sort of "white space" between the fields
27 -# if you don't know a serial number, put 999. if you don't know the elevation, put 0
28 -# for Nodes, put the same serial number for both Recoder and Sensor (since they are the same!)
29 -
30 -
31 -# EXAMPLE INSTRUMENT LABELS
32 -#LPR200 = ANU LPR-200 logger (beige box)
33 -#TSAWR = ANU TerraSAWR logger (yellow box)
34 -
35 -#TRILL120 = Trillium Compact 120s
36 -#TRILL20 = Trillium Compact 20s
37 -#TRILL120PH = Trillium Compact 120s PostHole
38 -#CMG6TD = Guralp 6TD
39 -#CMG3ESP = Guralp 3ESP
40 -#3DLITE = Lenarrtz 3D-LITE
41 -
42 -#SSNODE_C = output was in COUNTS (there is also SSNODE_MV, if you (accidentally!) output to millivolts etc)
43 -#SSNODE_5S = broadband (can also use SSNODE_BB)
44 -#SSNODE_.2S = shortperiod (can also use SSNODE_SP)
45 -
46 -#it doesn't matter too much what you use for equipment labels, so long as they are consistent and otherwise defined somewhere in the comments!
smartsolo node 2.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -1.0 MB
Content
smartsolo node.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -1.1 MB
Content
smartsolo.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -1.0 MB
Content
XWiki.XWikiRights[0]
Allow/Deny
... ... @@ -1,1 +1,0 @@
1 -Allow
Groups
... ... @@ -1,1 +1,0 @@
1 -XWiki.XWikiAllGroup
Levels
... ... @@ -1,1 +1,0 @@
1 -comment
XWiki.XWikiRights[1]
Allow/Deny
... ... @@ -1,1 +1,0 @@
1 -Allow
Levels
... ... @@ -1,1 +1,0 @@
1 -comment
Users
... ... @@ -1,1 +1,0 @@
1 -XWiki.XWikiGuest