Changes for page SmartSolo Node Seismometers

Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 8 added, 0 removed)
  • 1706153266647-145.png
  • 1706153354750-415.png
  • 1706153556166-231.jpeg
  • Smartsolo IGU BD3C 5 (2).jpg
  • Smartsolo IGU BD3C 5.jpg
  • smartsolo node 2.jpg
  • smartsolo node.jpg
  • smartsolo.jpg

Details

Page properties

Content

...	...	@@ -2,220 +2,380 @@
2	2	(((
3	3	(% class="col-xs-12 col-sm-8" %)
4	4	(((
5		-= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
	5	+= **Node Types** =
6	6
7		-blahblah
	7	+ANSIR carry two types of three-channel nodes
8	8
9		-== Sub-paragraph ==
	9	+* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
	10	+* **SmartSolo BD3C-5 (5-second Broad-Band)**
10	10
	12	+Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
11	11
12		-== ==
13	13
	15	+----
14	14
15		-= Smart Solo BD3C-5 (5 second) Broad-Band Node =
	17	+= **Programming Defaults** =
16	16
17		-Lorem
	19	+ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery power, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is VERY unlikely you will go over 64 Gb for one deploy). If using the "timed turnon" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
18	18
19		-[[image:1705196270090-364.png]]
20	20
	22	+== **Pre-Fieldwork Preparation** ==
21	21
22		-== GPS Considerations ==
	24	+(% class="box infomessage" %)
	25	+(((
	26	+(% class="box warningmessage" %)
	27	+(((
	28	+**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
23	23
24		-The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
	30	+**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days**
	31	+)))
	32	+)))
25	25
26		-= Keeping the Instruments Clean =
	34	+= **Installation** =
27	27
28		-Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
	36	+=== **1- Logbook documentation** ===
29	29
	38	+(((
	39	+**Essential Details**: Record the following in a logbook:
30	30
31		-= Charge Time, Instrument Life, and Charge During Storage & Shipping =
	41	+* Station name
	42	+* Latitude and longitude
	43	+* Names of team members present
	44	+* Date and local time of installation
	45	+* Serial number (SN) of the sensor
	46	+* Detailed notes on the site conditions and setup
32	32
33		-Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
	48	+=== **2- Node Placement** ===
	49	+)))
34	34
35		-Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
	51	+**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
36	36
	53	+**Site Analysis**:
37	37
38		-= Best Practices and Guide =
	55	+* **Take compass measurements away from the sensor as it will affect your measurement.**
	56	+* Take multiple photographs from various angles to document the site setup thoroughly.
	57	+* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
39	39
40		-== Install ==
	59	+=== **3- GPS Considerations** ===
41	41
42		-Logbook is required (used again for pick up & metadata creation)
	61	+(% class="wikigeneratedid" %)
	62	+The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. These nodes will not start recording without attaining a GPS lock and repeated attempts will excessively drain the battery.
43	43
44		-- station name
	64	+=== **4- Visibility and Location Marking** ===
45	45
46		-- lat / long
	66	+**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
47	47
48		-- team members
	68	+**GPS Marking**:
49	49
50		-- date and local time
	70	+* Use a GPS device to mark the instrument's exact location.
	71	+* Record this location in both your paper notes and the GPS device.
51	51
52		-- SN of sensor
	73	+=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5- Charge Time, Pre-Deployment & Post-Deployment**(%%) ===
53	53
54		-- notes on site
	75	+* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
	76	+* **Pre-Deployment Charging**:
	77	+** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
55	55
56		-Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
	79	+* **Operational Duration**:
	80	+** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
57	57
58		-Take compass measurement away from node and fences [make sure to adjust inclination angle]
	82	+* **Post-Retrieval Charging**:
	83	+** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
	84	+* **Storage and Shipping Charge Level**:
	85	+** Maintain a battery charge level of around 50-60% for both storage and shipping purposes.
	86	+** This charge level is recommended to prevent battery damage and is safe for transportation.
	87	+** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
59	59
60		-Take many photos from the site from different angles
	89	+=== ===
61	61
62		-Add a precise site description to the notes such as distances and orientations from landmarks
	91	+(((
	92	+=== **6- Data Sharing and Metadata Creation** ===
	93	+)))
63	63
64		-It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
	95	+**GPS Data**:
65	65
66		-Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
	97	+* Download the GPS file to a laptop. (???)
	98	+* Share this file on a drive accessible to all team members for uniform understanding of node locations.
67	67
68		-Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
	100	+**Photo Sharing**:
69	69
70		-Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
	102	+* Upload site photos to a shared platform (OneDrive, Dropbox, etc.).
	103	+* Integrating photos into Google Maps or Google Earth can be particularly beneficial for easy location referencing.
71	71
72		-Create metadata .xml file
	105	+**Metadata File**:
73	73
	107	+* Create and organize metadata via the ANU metadata standard (~*~*add example)
74	74
75		-== Removing/Demob ==
	109	+=== **7- Additional Best Practices** ===
76	76
77		-Download and then use the GPS file to locate the node
	111	+* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
	112	+* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass, and other equipment to ensure consistent and accurate data collection.
78	78
79		-Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.
	114	+* (((
	115	+==== **Keeping the Instruments Clean** ====
	116	+)))
	117	+* (((
	118	+Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
	119	+)))
80	80
	121	+----
81	81
82		-Upload photos of the site
	123	+=== **Seismic Station Demobilization and Documentation** ===
83	83
84		-- station name
	125	+1. (((
	126	+**Preparation for Demobilization**:
85	85
86		-- latitude
	128	+* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, clipboard, logbook, and compass ready in your tote bag.
	129	+)))
	130	+1. (((
	131	+**Locating the instrument**:
87	87
88		-- longitude
	133	+* Use the downloaded GPS file to accurately locate the node for demobilization.
	134	+* Import this KMZ file onto your phone for easy reference and location tracking.
	135	+* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
	136	+)))
	137	+1. (((
	138	+**Labeling Instruments for Demobilization**:
89	89
90		-- elevation
	140	+* Write the station name and the instrument’s serial number on a label.
	141	+* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
	142	+* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
	143	+)))
	144	+1. (((
	145	+**Photographing the Setup Node**:
91	91
92		-* SN of sensor – SN of battery (optional)
93		-* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
	147	+* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
	148	+* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
	149	+)))
	150	+1. (((
	151	+**Logging Demobilization Details**:
94	94
95		-Upload photos into Google Earth and on a shared drive
	153	+* Use the field logbook to note the time of demobilization, serial numbers, and station name.
	154	+* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
	155	+)))
	156	+1. (((
	157	+**Final Checks and Equipment Removal**:
96	96
97		-Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!).
	159	+* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
	160	+* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
98	98
99		-Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
	162	+
	163	+)))
100	100
101		-Take a photo of the entire setup node with the label on it + compass
	165	+[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
102	102
103		-Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
	167	+----
104	104
	169	+=== **Charging Procedure for Seismic Nodes** ===
105	105
106		-== Charging ==
	171	+1. (((
	172	+**Preparation for Charging**:
107	107
108		-Clean node prior to charging and harvesting the data
	174	+* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
109	109
110		-Remove battery (and spike) from the sensor by twisting the spike part of the instrument
	176	+
	177	+)))
	178	+1. (((
	179	+**Disassembling the Node**:
111	111
112		-Set 16 nodes into the charging box (spikes up)
	181	+* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
113	113
114		-Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
	183	+
	184	+)))
	185	+1. (((
	186	+**Setting Nodes in the Charging Box**:
115	115
116		-This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
	188	+* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
117	117
118		-[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
	190	+
	191	+)))
	192	+1. (((
	193	+**Monitoring the Charging Process**:
119	119
	195	+* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
	196	+* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
120	120
	198	+
	199	+)))
	200	+1. (((
	201	+**Updating Charge Status**:
121	121
122		-== Downloading and Converting Data to MiniSeed ==
	203	+* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
	204	+* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
	205	+)))
123	123
	207	+[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
124	124
125		-The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
126	126
127		-[[image:1705195543887-977.png]]
128	128
129	129
130		-Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
	212	+[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
131	131
132		-[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
	214	+----
133	133
	216	+=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
134	134
135		-Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
	218	+==== **Node Registration and Software Setup** ====
136	136
137		-[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
	220	+1. (((
	221	+**Registering Nodes in the System**:
138	138
139		-At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
	223	+* To begin, register the nodes in the system so the software can recognize them.
	224	+* Navigate to the installation folder of “SmartSoloApps SoloLite”.
	225	+* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
	226	+* To avoid double registration, replace the file each time you register a new node.
	227	+)))
	228	+1. (((
	229	+**Creating a New Project in SoloLite**:
140	140
141		-(% class="box warningmessage" %)
142		-(((
143		-**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
	231	+* Open the “SoloLite” software.
	232	+* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
	233	+* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
144	144	)))
145	145
146		-(% class="box warningmessage" %)
147		-(((
148		-**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
	236	+==== **Data Downloading Process** ====
	237	+
	238	+1. (((
	239	+**Initiating Data Download**:
	240	+
	241	+* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
	242	+* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
	243	+* Select all nodes and right-click to “force download”. This starts the download process.
	244	+* Completed downloads will appear as new folders in the Downloaded Data panel.
149	149	)))
	246	+1. (((
	247	+**Exporting Data in Readable Format**:
150	150
151		-A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
	249	+* Go to the “Tool” menu and select “export seismic data”.
	250	+* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
	251	+* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
	252	+* (% class="box warningmessage" %)
	253	+(((
	254	+* **Ensure to export data as "COUNTS", not "mV".**
152	152
153		-Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
	256	+* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db (a factor of 15.848932).**
	257	+)))
	258	+)))
154	154
155		-[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
	260	+==== **Handling Nodes During Download** ====
156	156
157		-When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
	262	+1. (((
	263	+**Monitoring Download Indicators**:
158	158
159		-(% class="box infomessage" %)
	265	+* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
	266	+* Disconnect nodes properly before unplugging anything.
	267	+* Be cautious: if the laptop enters sleep mode, the download will pause.
	268	+)))
	269	+1. (((
	270	+//**Investment in Storage Hardware**~://
	271	+
	272	+* (% class="box warningmessage" %)
160	160	(((
161		-**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
	274	+* **Use fast external hard drives to avoid limitations in data harvesting.**
	275	+
	276	+* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
162	162	)))
	278	+)))
	279	+1. (((
	280	+**Metadata and Time Settings**:
163	163
164		-When downloading, ensure that all metadata is saved along with the file.
	282	+* Ensure all metadata is saved with the file.
	283	+* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
	284	+)))
	285	+1. (((
	286	+**Finalizing the Download**:
165	165
166		-Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
	288	+* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
167	167
168		-//Once downloaded, mark the "D" box on your temporary labels!//
	290	+
	291	+)))
169	169
170		-== Converting data ==
	293	+[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
171	171
172		-Check the data all have been converted to miniseed correctly
173	173
174		-– 3 files per station per day
175	175
176		-* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
177		-* ~~ 5 Gb / node / month
	297	+[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
178	178
179		-//Tick ‘R’ box on the node label//
180	180
181	181
182		-== Cleaning ==
183	183
184		-If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
	302	+[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
185	185
186		-
187		-)))
188	188
189	189
	306	+[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
	307	+
	308	+
	309	+
	310	+[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
	311	+
	312	+----
	313	+
	314	+=== **Cleaning** ===
	315	+
	316	+**Procedure for Seismic Nodes:**
	317	+
	318	+* If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
	319	+
	320	+= =
	321	+)))
	322	+
190	190	(% class="col-xs-12 col-sm-4" %)
191	191	(((
192		-{{box title="**Contents**"}}
193		-{{toc/}}
194		-{{/box}}
	325	+(% class="box" %)
	326	+(((
	327	+**Contents**
195	195
196		-{{box title="= SmartSolo [[BD3C-5>>https://smartsolo.com/cp-4.html]] =
	329	+(% class="wikitoc" %)
	330	+* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
	331	+** [[Sub-paragraph>>path:#HSub-paragraph]]
	332	+** [[ >>path:#H]]
	333	+* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
	334	+** [[GPS Considerations>>path:#HGPSConsiderations]]
	335	+* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
	336	+* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
	337	+* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
	338	+** [[Install>>path:#HInstall]]
	339	+** [[Removing/Demob>>path:#HRemoving2FDemob]]
	340	+** [[Charging>>path:#HCharging]]
	341	+** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
	342	+** [[Converting data>>path:#HConvertingdata]]
	343	+** [[Cleaning>>path:#HCleaning]]
	344	+)))
197	197
198		-= [[image:Trillium compact posthole.jpg]] =
199	199
200		-|(% style=~"width:115px~" %)**Sensitivity **|(% style=~"width:112px~" %)5 seconds
201		-|(% style=~"width:139px~" %)**Size (Diameter x Height)**|(% style=~"width:88px~" %)? x ? cm
202		-|(% style=~"width:139px~" %)**Weight**|(% style=~"width:88px~" %)? kg"}}
203		-|(% style="width:228px" %)**Battery**|(% style="width:183px" %)lithium (30 days)
204		-
205		-{{/box}}
	347	+(% class="box" %)
	348	+(((
	349	+= SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
206	206
207		-{{box title="= SmartSolo [[IGU-16HR>>https://smartsolo.com/cp-3.html]] =
	351	+[[image:Smartsolo IGU BD3C 5 (2).jpg]]
208	208
209		-= [[image:Trillium compact posthole.jpg]] =
	353	+[[image:smartsolo.jpg]]
210	210
211		-|(% style=~"width:115px~" %)**Sensitivity **|(% style=~"width:112px~" %)0.2 seconds (5 Hz)
212		-|(% style=~"width:139px~" %)**Size (Diameter x Height)**|(% style=~"width:88px~" %)? x ? cm
213		-|(% style=~"width:139px~" %)**Weight**|(% style=~"width:88px~" %)? kg"}}
214		-|(% style="width:228px" %)**Battery**|(% style="width:183px" %)lithium (30 days)
215		-
216		-{{/box}}
	355	+|(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
	356	+|(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
	357	+|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
	358	+|(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
	359	+|(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
	360	+|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
	361	+)))
217	217
	363	+(% class="box" %)
	364	+(((
	365	+= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
218	218
	367	+[[image:smartsolo node.jpg]]
	368	+
	369	+[[image:smartsolo node 2.jpg]]
	370	+
	371	+|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
	372	+|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
	373	+|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
	374	+|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
	375	+|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
	376	+|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Lithium ion XXAh
	377	+)))
	378	+
219	219
220	220	)))
221	221	)))

1706153266647-145.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.7 MB

Content

1706153354750-415.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.1 MB

Content

1706153556166-231.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+839.4 KB

Content

Smartsolo IGU BD3C 5 (2).jpg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.JackD

Size

...	...	@@ -1,0 +1,1 @@
	1	+909.0 KB

Content

Smartsolo IGU BD3C 5.jpg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.JackD

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.7 MB

Content

smartsolo node 2.jpg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.JackD

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.0 MB

Content

smartsolo node.jpg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.JackD

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.1 MB

Content

smartsolo.jpg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.JackD

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.0 MB

Content