Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 78.1
edited by Jack Dent
on 2025/08/01 16:09
Change comment: There is no comment for this version
To version 60.4
edited by robert
on 2025/07/16 16:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.JackD
1 +XWiki.robert
Content
... ... @@ -4,48 +4,27 @@
4 4  (((
5 5  = **Node Types** =
6 6  
7 -ANSIR carry two types of three-channel nodes, and one type of one-channel node:
7 +ANSIR carry two types of three-channel nodes
8 8  
9 9  * **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 -* **SmartSolo BD3C-5 (5 Second Broadband)**
11 -* **SmartSolo IGU 16 1C (5 Hz Short Period, single channel)**
10 +* **SmartSolo BD3C-5 (5 Second Broad-Band)**
12 12  
13 -The three-channel nodes have a battery capacity of ~~30 days, whereas the single-channel type has a capacity of ~~100 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
12 +Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
14 14  
14 +
15 15  ----
16 16  
17 17  = **Programming Defaults** =
18 18  
19 -The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.
19 +We recommend that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed). These are what we use for our internal experiments.
20 20  
21 -[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]
21 +**Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
22 22  
23 -[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]
24 24  
25 -FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
26 -
27 -Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
28 -
29 -Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
30 -
31 -If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
32 -
33 -In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
34 -
35 -Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
36 -
37 -GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
38 -
39 -Bluetooth (BB nodes only) should be turned OFF to conserve power.
40 -
41 -We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
42 -
43 -{{info}}
44 -**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
45 -{{/info}}
46 -
47 47  = **Fieldwork Preparation** =
48 48  
26 +(% class="box infomessage" %)
27 +(((
49 49  (% class="box warningmessage" %)
50 50  (((
51 51  **INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
... ... @@ -54,6 +54,7 @@
54 54  
55 55  **We have had good experience with the 4Tb Samsung T7 Shield drives.**
56 56  )))
36 +)))
57 57  
58 58  == Magnets ==
59 59  
... ... @@ -65,25 +65,18 @@
65 65  
66 66  = **Installation** =
67 67  
68 -(% class="box infomessage" %)
69 -(((
70 -**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
71 -)))
72 -
73 73  == 1. Logbook documentation ==
74 74  
75 75  (((
76 -**Essential Details** for field logs:
51 +**Essential Details**: Record the following in a logbook:
77 77  
78 78  * Station name
79 -* Latitude, longitude, elevation
54 +* Latitude and longitude
80 80  * Names of team members present
81 -* Date and both local & UTC time of installation/removal
82 -* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
83 -* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
56 +* Date and local time of installation
57 +* Serial number (SN) of the sensor
58 +* Detailed notes on the site conditions and setup
84 84  
85 -[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
86 -
87 87  == 2. Node Placement ==
88 88  )))
89 89  
... ... @@ -92,8 +92,8 @@
92 92  **Site Analysis**:
93 93  
94 94  * **Take compass measurements away from the sensor as it will affect your measurement.**
95 -* Take photographs from various angles to document the site setup thoroughly.
96 -* Include a detailed site description in your notes
68 +* Take multiple photographs from various angles to document the site setup thoroughly.
69 +* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
97 97  
98 98  == 3. GPS Considerations ==
99 99  
... ... @@ -274,9 +274,9 @@
274 274  * Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
275 275  * (% class="box warningmessage" %)
276 276  (((
277 -* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**
250 +* **Ensure to export data as "COUNTS", not "mV".**
278 278  
279 -* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**
252 +* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db for short period nodes (a factor of 15.848932), and 6db for broadband nodes).**
280 280  )))
281 281  )))
282 282  
... ... @@ -297,7 +297,6 @@
297 297  * **Use fast external hard drives to avoid limitations in data harvesting.**
298 298  
299 299  * **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
300 -* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
301 301  )))
302 302  )))
303 303  1. (((
... ... @@ -337,7 +337,7 @@
337 337  
338 338  = **Cleaning** =
339 339  
340 -When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
312 +When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipedown. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
341 341  
342 342  = **Weights (for shipping)** =
343 343  
... ... @@ -387,7 +387,7 @@
387 387  
388 388  (% class="box" %)
389 389  (((
390 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
362 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
391 391  
392 392  [[image:smartsolo node.jpg]]
393 393  
... ... @@ -405,78 +405,6 @@
405 405  )))
406 406  )))
407 407  
408 -(% class="box" %)
409 -(((
410 -= SmartSolo BD3C-16 Portable Battery Charger =
411 -
412 -[[image:20250729_125049.jpg]]
413 -
414 -|**Dimensions (LxHxW)**|558 x 357 x 300mm
415 -|**Input rating**|100-210V - 50/60Hz
416 -|**Power**|1000W
417 -|**Weight**|14.5kg
418 -|**Weight with cables**|21kg
380 +
419 419  )))
420 -
421 -(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
422 -(((
423 -= SmartSolo IGU-16 Portable Data Harvester =
424 -
425 -[[image:20250729_124747.jpg]]
426 -
427 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
428 -|**Input rating**|100-210V - 50/60Hz
429 -|**Power**|100W
430 -|**Weight**|21.5 - 24kg
431 -|**Slots no.**|16
432 -|**Download Speed**|20MB/sec/slot
433 433  )))
434 -
435 -(% class="box" %)
436 -(((
437 -= SmartSolo IGU-16 Portable Battery Charger =
438 -
439 -[[image:20250729_124644.jpg]]
440 -
441 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
442 -|**Input rating**|100-210V - 50/60Hz
443 -|**Power**|640W
444 -|**Weight**|26.3kg
445 -|**Slots no.**|16
446 -)))
447 -
448 -(% class="box" %)
449 -(((
450 -= SmartSolo BD3C-5 Carry Case =
451 -
452 -[[image:20250729_124957.jpg]]
453 -
454 -
455 -|**Dimensions (LxHxW)**|590 x 225 x 405mm
456 -|**Weight**|8.2kg
457 -|**Slots no.**|6
458 -)))
459 -
460 -(% class="box" %)
461 -(((
462 -= SmartSolo IGU-16 3C Carry Bag =
463 -
464 -[[image:20250729_124502.jpg]]
465 -
466 -|**Dimensions (LxHxW)**|230 x 340 x 310mm
467 -|**Weight**|3.6kg
468 -|**Slots no.**|6
469 -)))
470 -
471 -(% class="box" %)
472 -(((
473 -= SmartSolo IGU-16 1C Carry Bag =
474 -
475 -[[image:20250729_124558.jpg]]
476 -
477 -|**Dimensions (LxHxW)**|225 x 200 x 550mm
478 -|**Weight**|
479 -|**Slots no.**|6
480 -)))
481 -)))
482 -)))
20250729_124502.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -457.6 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -106.7 KB
Content