Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 76.1
edited by robert
on 2025/07/31 20:11
Change comment: There is no comment for this version
To version 66.1
edited by Jack Dent
on 2025/07/31 09:21
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.robert
1 +XWiki.JackD
Content
... ... @@ -15,34 +15,10 @@
15 15  
16 16  = **Programming Defaults** =
17 17  
18 -The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.
18 +We recommend that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed). These are what we use for our internal experiments.
19 19  
20 -[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]
20 +**Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
21 21  
22 -[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]
23 -
24 -FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
25 -
26 -Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
27 -
28 -Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
29 -
30 -If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
31 -
32 -In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
33 -
34 -Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
35 -
36 -GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
37 -
38 -Bluetooth (BB nodes only) should be turned OFF to conserve power.
39 -
40 -We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
41 -
42 -{{info}}
43 -**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
44 -{{/info}}
45 -
46 46  = **Fieldwork Preparation** =
47 47  
48 48  (% class="box warningmessage" %)
... ... @@ -336,7 +336,7 @@
336 336  
337 337  = **Cleaning** =
338 338  
339 -When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
315 +When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipedown. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
340 340  
341 341  = **Weights (for shipping)** =
342 342  
... ... @@ -386,7 +386,7 @@
386 386  
387 387  (% class="box" %)
388 388  (((
389 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
365 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
390 390  
391 391  [[image:smartsolo node.jpg]]
392 392  
... ... @@ -408,7 +408,6 @@
408 408  (((
409 409  = SmartSolo BD3C-16 Portable Battery Charger =
410 410  
411 -[[image:20250729_125049.jpg]]
412 412  
413 413  |**Dimensions (LxHxW)**|558 x 357 x 300mm
414 414  |**Input rating**|100-210V - 50/60Hz
... ... @@ -421,7 +421,6 @@
421 421  (((
422 422  = SmartSolo IGU-16 Portable Data Harvester =
423 423  
424 -[[image:20250729_124747.jpg]]
425 425  
426 426  |**Dimensions (LxHxW)**|625 x 500 x 366mm
427 427  |**Input rating**|100-210V - 50/60Hz
... ... @@ -431,51 +431,26 @@
431 431  |**Download Speed**|20MB/sec/slot
432 432  )))
433 433  
434 -(% class="box" %)
435 -(((
436 -= SmartSolo IGU-16 Portable Battery Charger =
437 437  
438 -[[image:20250729_124644.jpg]]
439 439  
410 +SmartSolo IGU-16 Portable Battery Charger
411 +
412 +[[image:20250729_124747.jpg]]
413 +
440 440  |**Dimensions (LxHxW)**|625 x 500 x 366mm
441 441  |**Input rating**|100-210V - 50/60Hz
442 442  |**Power**|640W
443 443  |**Weight**|26.3kg
444 444  |**Slots no.**|16
445 -)))
446 446  
447 -(% class="box" %)
448 -(((
449 -= SmartSolo BD3C-5 Carry Case =
420 +SmartSolo IGU-16 Carry Bag
450 450  
451 -[[image:20250729_124957.jpg]]
452 -
453 -
454 -|**Dimensions (LxHxW)**|590 x 225 x 405mm
455 -|**Weight**|8.2kg
422 +|**Dimensions (LxHxW)**|230 x 340 x 310mm
456 456  |**Slots no.**|6
457 -)))
458 458  
459 -(% class="box" %)
460 -(((
461 -= SmartSolo IGU-16 3C Carry Bag =
425 +SmartSolo IGU-16 Carry Bag
462 462  
463 -[[image:20250729_124502.jpg]]
464 -
465 465  |**Dimensions (LxHxW)**|230 x 340 x 310mm
466 -|**Weight**|3.6kg
467 467  |**Slots no.**|6
468 468  )))
469 -
470 -(% class="box" %)
471 -(((
472 -= SmartSolo IGU-16 1C Carry Bag =
473 -
474 -[[image:20250729_124558.jpg]]
475 -
476 -|**Dimensions (LxHxW)**|225 x 200 x 550mm
477 -|**Weight**|
478 -|**Slots no.**|6
479 479  )))
480 -)))
481 -)))
20250729_124502.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -457.6 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -106.7 KB
Content