Skip to Content
Last modified by robert on 2025/06/16 07:51
From version 7.2
edited by robert
on 2024/01/14 12:28
Change comment: There is no comment for this version
To version 7.1
edited by robert
on 2024/01/14 12:24
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -35,7 +35,7 @@
35 35  
36 36  = Best Practices and Guide =
37 37  
38 -== Install ==
38 +== Install ==
39 39  
40 40  Logbook is required (used again for pick up & metadata creation)
41 41  
... ... @@ -70,7 +70,7 @@
70 70  Create metadata .xml file
71 71  
72 72  
73 -== Removing/Demob ==
73 +== Removing/Demob ==
74 74  
75 75  Download and then use the GPS file to locate the node 
76 76  
... ... @@ -77,7 +77,7 @@
77 77  Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
78 78  
79 79  
80 -Upload photos of the site  
80 +Upload photos of the site
81 81  
82 82  - station name
83 83  
... ... @@ -88,7 +88,7 @@
88 88  - elevation
89 89  
90 90  * SN of sensor – SN of battery (optional)
91 -* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
91 +* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
92 92  
93 93  Upload photos into Google Earth and on a shared drive
94 94  
... ... @@ -113,35 +113,7 @@
113 113  
114 114  This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
115 115  
116 -
117 -== Downloading and Converting Data to MiniSeed ==
118 -
119 -
120 -The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
121 -
122 -[[image:1705195543887-977.png]]
123 -
124 -Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
125 -
126 -[[image:1705195543890-537.png]]
127 -
128 -Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
129 -
130 -[[image:1705195543891-334.png]]
131 -
132 -At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference. A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
133 -
134 -Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
135 -
136 -[[image:1705195543898-365.png]]
137 -
138 -When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
139 -
140 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
141 -
142 -When downloading, ensure that all metadata is saved along with the file.
143 -
144 -Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight. 
116 +
145 145  )))
146 146  
147 147  
1705195543887-977.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -259.0 KB
Content
1705195543890-537.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -52.4 KB
Content
1705195543891-334.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -75.6 KB
Content
1705195543898-365.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -141.1 KB
Content