Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 7.1
edited by robert
on 2024/01/14 12:24
Change comment: There is no comment for this version
To version 44.1
edited by robert
on 2024/05/14 18:38
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -2,150 +2,355 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
5 += **Node Types** =
6 6  
7 -blahblah
7 +ANSIR carry two types of three-channel nodes
8 8  
9 -== Sub-paragraph ==
9 +* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 +* **SmartSolo BD3C-5 (5 Second Broad-Band)**
10 10  
12 +Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
11 11  
12 -== ==
13 13  
15 +----
14 14  
15 -= Smart Solo BD3C-5 (5 second) Broad-Band Node =
17 += **Programming Defaults** =
16 16  
17 -Lorem
19 +ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
18 18  
19 19  
20 -== GPS Considerations ==
22 += **Fieldwork Preparation** =
21 21  
22 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
24 +(% class="box infomessage" %)
25 +(((
26 +(% class="box warningmessage" %)
27 +(((
28 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
23 23  
24 -== Keeping the Instruments Clean ==
30 +**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
31 +)))
32 +)))
25 25  
26 -Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
34 += **Installation** =
27 27  
36 +=== **1- Logbook documentation** ===
28 28  
29 -= Charge Time, Instrument Life, and Charge During Storage & Shipping =
38 +(((
39 +**Essential Details**: Record the following in a logbook:
30 30  
31 -Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
41 +* Station name
42 +* Latitude and longitude
43 +* Names of team members present
44 +* Date and local time of installation
45 +* Serial number (SN) of the sensor
46 +* Detailed notes on the site conditions and setup
32 32  
33 -Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
48 +=== **2- Node Placement** ===
49 +)))
34 34  
51 +**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
35 35  
36 -= Best Practices and Guide =
53 +**Site Analysis**:
37 37  
38 -== Install ==
55 +* **Take compass measurements away from the sensor as it will affect your measurement.**
56 +* Take multiple photographs from various angles to document the site setup thoroughly.
57 +* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
39 39  
40 -Logbook is required (used again for pick up & metadata creation)
59 +=== **3- GPS Considerations** ===
41 41  
42 -- station name
61 +(% class="wikigeneratedid" %)
62 +The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
43 43  
44 -- lat / long
64 +=== **4- Visibility and Location Marking** ===
45 45  
46 -- team members
66 +**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
47 47  
48 -- date and local time
68 +**GPS Marking**:
49 49  
50 -- SN of sensor
70 +* Use a GPS device to mark the instrument's exact location.
71 +* Record this location in both your paper notes and the GPS device.
51 51  
52 -- notes on site
73 +=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5- Charge Time, Pre-Deployment & Post-Deployment**(%%) ===
53 53  
54 -Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
75 +* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
76 +* **Pre-Deployment Charging**:
77 +** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
55 55  
56 -Take compass measurement away from node and fences [make sure to adjust inclination angle]
79 +* **Operational Duration**:
80 +** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
57 57  
58 -Take many photos from the site from different angles 
82 +* **Post-Retrieval Charging**:
83 +** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
84 +* **Storage and Shipping Charge Level**:
85 +** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
86 +** This charge level is recommended to prevent battery damage and is safe for transportation.
87 +** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
59 59  
60 -Add a precise site description to the notes such as distances and orientations from landmarks 
89 +(((
90 +=== **6- Data Sharing and Metadata Creation** ===
91 +)))
61 61  
62 -It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
93 +**GPS Data**:
63 63  
64 -Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
95 +* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
65 65  
66 -Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
97 +**Photo Sharing**:
67 67  
68 -Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
99 +* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
69 69  
70 -Create metadata .xml file
101 +**Metadata File**:
71 71  
103 +* Create and organize metadata via the ANU metadata standard (~*~*add example)
72 72  
73 -== Removing/Demob ==
105 +=== **7- Additional Best Practices** ===
74 74  
75 -Download and then use the GPS file to locate the node 
107 +* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
108 +* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
76 76  
77 -Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
110 +* (((
111 +==== **Keeping the Instruments Clean** ====
112 +)))
113 +* (((
114 +Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
115 +)))
78 78  
117 +----
79 79  
80 -Upload photos of the site
119 += **Seismic Station Demobilization and Documentation** =
81 81  
82 -- station name
121 +1. (((
122 +**Preparation for Demobilization**:
83 83  
84 -- latitude
124 +* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
125 +)))
126 +1. (((
127 +**Locating the instrument**:
85 85  
86 -- longitude
129 +* Use the downloaded GPS file to accurately locate the node for demobilization.
130 +* Import this KMZ file onto your phone for easy reference and location tracking.
131 +* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
132 +)))
133 +1. (((
134 +**Labeling Instruments for Demobilization**:
87 87  
88 -- elevation
136 +* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
137 +* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
138 +* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
139 +)))
140 +1. (((
141 +**Photographing the Setup Node**:
89 89  
90 -* SN of sensor – SN of battery (optional)
91 -* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
143 +* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
144 +* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
145 +)))
146 +1. (((
147 +**Logging Demobilization Details**:
92 92  
93 -Upload photos into Google Earth and on a shared drive
149 +* Use the field logbook to note the time of demobilization, serial numbers, and station name.
150 +* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
151 +)))
152 +1. (((
153 +**Final Checks and Equipment Removal**:
94 94  
95 -Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
155 +* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
156 +* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
96 96  
97 -Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument.
158 +
159 +)))
98 98  
99 -Take a photo of the entire setup node with the label on it + compass 
161 +[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
100 100  
101 -Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
163 +----
102 102  
165 += **Charging Procedure for Seismic Nodes** =
103 103  
104 -== Charging ==
167 +1. (((
168 +=== **Preparation for Charging**: ===
105 105  
106 -Clean node prior to charging and harvesting the data
170 +* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
171 +)))
172 +1. (((
173 +=== **Disassembling the Node**: ===
107 107  
108 -Remove battery (and spike) from the sensor by twisting the spike part of the instrument
175 +* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
176 +)))
177 +1. (((
178 +=== **Setting Nodes in the Charging Box**: ===
109 109  
110 -Set 16 nodes into the charging box (spikes up)
180 +* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
181 +)))
182 +1. (((
183 +=== **Monitoring the Charging Process**: ===
111 111  
112 -Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
185 +* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
186 +* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
187 +)))
188 +1. (((
189 +=== **Updating Charge Status**: ===
113 113  
114 -This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
191 +* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
192 +* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
193 +)))
115 115  
195 +[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
196 +
197 +
198 +
199 +
200 +[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
201 +
202 +----
203 +
204 +=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
205 +
206 +==== **Node Registration and Software Setup** ====
207 +
208 +1. (((
209 +**Registering Nodes in the System**:
210 +
211 +* To begin, register the nodes in the system so the software can recognize them.
212 +* Navigate to the installation folder of “SmartSoloApps SoloLite”.
213 +* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
214 +* To avoid double registration, replace the file each time you register a new node.
215 +)))
216 +1. (((
217 +**Creating a New Project in SoloLite**:
218 +
219 +* Open the “SoloLite” software.
220 +* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
221 +* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
222 +)))
223 +
224 +==== **Data Downloading Process** ====
225 +
226 +1. (((
227 +**Initiating Data Download**:
228 +
229 +* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
230 +* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
231 +* Select all nodes and right-click to “force download”. This starts the download process.
232 +* Completed downloads will appear as new folders in the Downloaded Data panel.
233 +)))
234 +1. (((
235 +**Exporting Data in Readable Format**:
236 +
237 +* Go to the “Tool” menu and select “export seismic data”.
238 +* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
239 +* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
240 +* (% class="box warningmessage" %)
241 +(((
242 +* **Ensure to export data as "COUNTS", not "mV".**
243 +
244 +* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db (a factor of 15.848932).**
245 +)))
246 +)))
247 +
248 +==== **Handling Nodes During Download** ====
249 +
250 +1. (((
251 +**Monitoring Download Indicators**:
252 +
253 +* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
254 +* Disconnect nodes properly before unplugging anything.
255 +* Be cautious: if the laptop enters sleep mode, the download will pause.
256 +)))
257 +1. (((
258 +//**Investment in Storage Hardware**~://
259 +
260 +* (% class="box warningmessage" %)
261 +(((
262 +* **Use fast external hard drives to avoid limitations in data harvesting.**
263 +
264 +* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
265 +)))
266 +)))
267 +1. (((
268 +**Metadata and Time Settings**:
269 +
270 +* Ensure all metadata is saved with the file.
271 +* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
272 +)))
273 +1. (((
274 +**Finalizing the Download**:
275 +
276 +* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
277 +
116 116  
117 117  )))
118 118  
281 +[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
119 119  
283 +
284 +
285 +[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
286 +
287 +
288 +
289 +
290 +[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
291 +
292 +
293 +
294 +[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
295 +
296 +
297 +
298 +[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
299 +
300 +----
301 +
302 +=== **Cleaning** ===
303 +
304 +**Procedure for Seismic Nodes:**
305 +
306 +* If the nodes are placed in a sturdy plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
307 +
308 += =
309 +)))
310 +
120 120  (% class="col-xs-12 col-sm-4" %)
121 121  (((
122 -{{box title="**Contents**"}}
313 +(% class="box" %)
314 +(((
315 +**Contents**
316 +
123 123  {{toc/}}
124 -{{/box}}
125 125  
126 -{{box title="= SmartSolo [[BD3C-5>>https://smartsolo.com/cp-4.html]] =
319 +
320 +)))
127 127  
128 -= [[image:Trillium compact posthole.jpg]] =
322 +(% class="box" %)
323 +(((
324 += SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
129 129  
130 -|(% style=~"width:115px~" %)**Sensitivity **|(% style=~"width:112px~" %)5 seconds
131 -|(% style=~"width:139px~" %)**Size (Diameter x Height)**|(% style=~"width:88px~" %)? x ? cm
132 -|(% style=~"width:139px~" %)**Weight**|(% style=~"width:88px~" %)? kg"}}
133 -|(% style="width:228px" %)**Battery**|(% style="width:183px" %)lithium (30 days)
134 -
135 -{{/box}}
326 +[[image:Smartsolo IGU BD3C 5 (2).jpg]]
136 136  
137 -{{box title="= SmartSolo [[IGU-16HR>>https://smartsolo.com/cp-3.html]] =
328 +[[image:smartsolo.jpg]]
138 138  
139 -= [[image:Trillium compact posthole.jpg]] =
330 +|(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
331 +|(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
332 +|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
333 +|(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
334 +|(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
335 +|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
336 +)))
140 140  
141 -|(% style=~"width:115px~" %)**Sensitivity **|(% style=~"width:112px~" %)0.2 seconds (5 Hz)
142 -|(% style=~"width:139px~" %)**Size (Diameter x Height)**|(% style=~"width:88px~" %)? x ? cm
143 -|(% style=~"width:139px~" %)**Weight**|(% style=~"width:88px~" %)? kg"}}
144 -|(% style="width:228px" %)**Battery**|(% style="width:183px" %)lithium (30 days)
145 -
146 -{{/box}}
338 +(% class="box" %)
339 +(((
340 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
147 147  
342 +[[image:smartsolo node.jpg]]
148 148  
344 +[[image:smartsolo node 2.jpg]]
345 +
346 +|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
347 +|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
348 +|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
349 +|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
350 +|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
351 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Lithium ion XXAh
352 +)))
353 +
149 149  
150 150  )))
151 151  )))
1705195543887-977.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +259.0 KB
Content
1705195543890-537.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +52.4 KB
Content
1705195543891-334.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +75.6 KB
Content
1705195543898-365.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +141.1 KB
Content
1705195933422-337.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 MB
Content
1705196270090-364.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +375.2 KB
Content
1706153266647-145.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +839.4 KB
Content
Smartsolo IGU BD3C 5 (2).jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +909.0 KB
Content
Smartsolo IGU BD3C 5.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +2.7 MB
Content
smartsolo node 2.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +1.0 MB
Content
smartsolo node.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +1.1 MB
Content
smartsolo.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +1.0 MB
Content