Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 65.1
edited by Jack Dent
on 2025/07/31 09:20
Change comment: There is no comment for this version
To version 77.1
edited by Jack Dent
on 2025/08/01 16:08
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -4,21 +4,46 @@
4 4  (((
5 5  = **Node Types** =
6 6  
7 -ANSIR carry two types of three-channel nodes
7 +ANSIR carry two types of three-channel nodes, and one type of one-channel node:
8 8  
9 9  * **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 10  * **SmartSolo BD3C-5 (5 Second Broadband)**
11 +* **SmartSolo IGU 16 1C (5 Hz Short Period, single channel)**
11 11  
12 -Both have a battery capacity of around 30 days. The programming, operation and downloading procedures for both types of SmartSolo nodes are also similar.
13 +All have a battery capacity of around 30 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
13 13  
14 14  ----
15 15  
16 16  = **Programming Defaults** =
17 17  
18 -We recommend that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed). These are what we use for our internal experiments.
19 +The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.
19 19  
20 -**Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
21 +[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]
21 21  
23 +[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]
24 +
25 +FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
26 +
27 +Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
28 +
29 +Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
30 +
31 +If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
32 +
33 +In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
34 +
35 +Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
36 +
37 +GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
38 +
39 +Bluetooth (BB nodes only) should be turned OFF to conserve power.
40 +
41 +We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
42 +
43 +{{info}}
44 +**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
45 +{{/info}}
46 +
22 22  = **Fieldwork Preparation** =
23 23  
24 24  (% class="box warningmessage" %)
... ... @@ -312,7 +312,7 @@
312 312  
313 313  = **Cleaning** =
314 314  
315 -When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipedown. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
340 +When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
316 316  
317 317  = **Weights (for shipping)** =
318 318  
... ... @@ -362,7 +362,7 @@
362 362  
363 363  (% class="box" %)
364 364  (((
365 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
390 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
366 366  
367 367  [[image:smartsolo node.jpg]]
368 368  
... ... @@ -380,9 +380,11 @@
380 380  )))
381 381  )))
382 382  
408 +(% class="box" %)
409 +(((
383 383  = SmartSolo BD3C-16 Portable Battery Charger =
384 384  
385 -[[image:20250729_125049 (1).jpg]]
412 +[[image:20250729_125049.jpg]]
386 386  
387 387  |**Dimensions (LxHxW)**|558 x 357 x 300mm
388 388  |**Input rating**|100-210V - 50/60Hz
... ... @@ -389,8 +389,11 @@
389 389  |**Power**|1000W
390 390  |**Weight**|14.5kg
391 391  |**Weight with cables**|21kg
419 +)))
392 392  
393 -SmartSolo IGU-16 Portable Data Harvester
421 +(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
422 +(((
423 += SmartSolo IGU-16 Portable Data Harvester =
394 394  
395 395  [[image:20250729_124747.jpg]]
396 396  
... ... @@ -400,10 +400,13 @@
400 400  |**Weight**|21.5 - 24kg
401 401  |**Slots no.**|16
402 402  |**Download Speed**|20MB/sec/slot
433 +)))
403 403  
404 -SmartSolo IGU-16 Portable Battery Charger
435 +(% class="box" %)
436 +(((
437 += SmartSolo IGU-16 Portable Battery Charger =
405 405  
406 -[[image:20250729_124747.jpg]]
439 +[[image:20250729_124644.jpg]]
407 407  
408 408  |**Dimensions (LxHxW)**|625 x 500 x 366mm
409 409  |**Input rating**|100-210V - 50/60Hz
... ... @@ -410,15 +410,40 @@
410 410  |**Power**|640W
411 411  |**Weight**|26.3kg
412 412  |**Slots no.**|16
446 +)))
413 413  
414 -SmartSolo IGU-16 Carry Bag
448 +(% class="box" %)
449 +(((
450 += SmartSolo BD3C-5 Carry Case =
415 415  
416 -|**Dimensions (LxHxW)**|230 x 340 x 310mm
452 +[[image:20250729_124957.jpg]]
453 +
454 +
455 +|**Dimensions (LxHxW)**|590 x 225 x 405mm
456 +|**Weight**|8.2kg
417 417  |**Slots no.**|6
458 +)))
418 418  
419 -SmartSolo IGU-16 Carry Bag
460 +(% class="box" %)
461 +(((
462 += SmartSolo IGU-16 3C Carry Bag =
420 420  
464 +[[image:20250729_124502.jpg]]
465 +
421 421  |**Dimensions (LxHxW)**|230 x 340 x 310mm
467 +|**Weight**|3.6kg
422 422  |**Slots no.**|6
423 423  )))
470 +
471 +(% class="box" %)
472 +(((
473 += SmartSolo IGU-16 1C Carry Bag =
474 +
475 +[[image:20250729_124558.jpg]]
476 +
477 +|**Dimensions (LxHxW)**|225 x 200 x 550mm
478 +|**Weight**|
479 +|**Slots no.**|6
424 424  )))
481 +)))
482 +)))
20250729_124502.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +457.6 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +106.7 KB
Content