Skip to Content
Last modified by robert on 2026/01/19 17:43
From version 55.1
edited by KB
on 2025/05/26 13:10
Change comment: There is no comment for this version
To version 97.1
edited by KB
on 2026/01/19 13:47
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SmartSolo Seismometers
1 +SmartSolo Node Seismometers
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Kimberley
1 +XWiki.KB
Content
... ... @@ -4,64 +4,107 @@
4 4  (((
5 5  = **Node Types** =
6 6  
7 -ANSIR carry two types of three-channel nodes
7 +ANSIR supply two types of three-channel nodes, and one type of one-channel node:
8 8  
9 -* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 -* **SmartSolo BD3C-5 (5 Second Broad-Band)**
9 +* **SmartSolo IGU 16HR 3C (5 Hz, 'very' short period)**
10 +* **SmartSolo BD3C-5 (5 second, short period)**
11 +* **SmartSolo IGU 16 1C (5 Hz, 'very' short period, single channel)**
11 11  
12 -Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
13 +The three-channel nodes have a theoretical battery capacity of ~~30 days, whereas the single-channel type has a capacity of ~~50 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
13 13  
15 +(% class="box infomessage" %)
16 +(((
17 +**Freight update, 2026: **Freight options for lithium-ion batteries are changing in 2025/2026 to comply with updated transport safety regulations. This will impact supply of IGU 16 (<100Wh) and BD3C (168Wh) nodes. Advice will be sought from freighters on a case-by-case basis while they implement new guidelines.
18 +)))
14 14  
15 15  ----
16 16  
17 17  = **Programming Defaults** =
18 18  
19 -ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
24 +The nodes must be programmed in the SoloLite software prior to use. The screenshots below show our recommended parameters for the 5 Hz (16HR-3C) and 5 second (BDC3-5) nodes.
20 20  
26 +[[IGU16HR-3C programming screen set at 250 Hz. Ensure circled areas are set!>>image:5Hz_node_programming.labels.png||alt="IGU-16 3C programming screen" data-xwiki-image-label="IGU-16 3C programming screen set at 250 Hz. Ensure that the circled areas are set!"]]
21 21  
28 +[[BD3C-5 programming screen set at 250 Hz. Ensure circled areas are set!>>image:5S_node_programming.labels.png||alt="BD3C-5 programming screen set at 250 hz. Ensure that the circled areas are set!"]]
29 +
30 +
31 +FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
32 +
33 +Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
34 +
35 +Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
36 +
37 +If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
38 +
39 +In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
40 +
41 +Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
42 +
43 +GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
44 +
45 +Bluetooth (BD3C-5 only) should be turned OFF to conserve power.
46 +
47 +We recommend that the 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
48 +
49 +{{info}}
50 +**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
51 +{{/info}}
52 +
22 22  = **Fieldwork Preparation** =
23 23  
24 -(% class="box infomessage" %)
25 -(((
26 26  (% class="box warningmessage" %)
27 27  (((
28 28  **INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
29 29  
30 30  **Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
60 +
61 +**We have had good experience with the 4Tb Samsung T7 Shield drives.**
31 31  )))
32 -)))
33 33  
64 +== Magnets ==
65 +
66 +If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).
67 +
68 +== Animal-Proofing ==
69 +
70 +We have experienced interference from animals (foxes, dogs, goats) digging up and carrying nodes off for tens or hundreds of metres. It is helpful to minimise human and food smells (particularly on the rope handles) when working in areas where this is a risk. Or, wipe down affected nodes with 50-80% methylated spirits if extensive handling can not be avoided.
71 +
34 34  = **Installation** =
35 35  
36 -== **1. Logbook documentation** ==
74 +(% class="box infomessage" %)
75 +(((
76 +**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
77 +)))
37 37  
79 +== 1. Logbook documentation ==
80 +
38 38  (((
39 -**Essential Details**: Record the following in a logbook:
82 +**Essential Details** for field logs:
40 40  
41 41  * Station name
42 -* Latitude and longitude
85 +* Latitude, longitude, elevation
43 43  * Names of team members present
44 -* Date and local time of installation
45 -* Serial number (SN) of the sensor
46 -* Detailed notes on the site conditions and setup
87 +* Date and both local & UTC time of installation/removal
88 +* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
89 +* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
47 47  
48 -== **2. Node Placement** ==
91 +[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
92 +
93 +== 2. Node Placement ==
49 49  )))
50 50  
51 -**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
52 -
53 53  **Site Analysis**:
54 54  
55 55  * **Take compass measurements away from the sensor as it will affect your measurement.**
56 -* Take multiple photographs from various angles to document the site setup thoroughly.
57 -* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
99 +* Take photographs from various angles to document the site setup thoroughly.
100 +* Include a detailed site description in your notes
58 58  
59 -== **3. GPS Considerations** ==
102 +== 3. GPS Considerations ==
60 60  
61 61  (% class="wikigeneratedid" %)
62 62  The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
63 63  
64 -== **4. Visibility and Location Marking** ==
107 +== 4. Visibility and Location Marking ==
65 65  
66 66  **Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
67 67  
... ... @@ -70,7 +70,7 @@
70 70  * Use a GPS device to mark the instrument's exact location.
71 71  * Record this location in both your paper notes and the GPS device.
72 72  
73 -== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5. Charge Time, Pre-Deployment & Post-Deployment**(%%) ==
116 +== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5. Charge Time, Pre-Deployment & Post-Deployment(%%) ==
74 74  
75 75  * **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
76 76  * **Pre-Deployment Charging**:
... ... @@ -80,19 +80,22 @@
80 80  ** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
81 81  
82 82  * **Post-Retrieval Charging**:
83 -** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
84 -* **Storage and Shipping Charge Level**:
85 -** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
86 -** This charge level is recommended to prevent battery damage and is safe for transportation.
87 -** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
126 +** After retrieval, charge the instruments to about 50-60% (indicated by ORANGE LED) unless they are to be immediately re-deployed or transported.
127 +* **State of Charge (SoC) for Storage**:
128 +** Maintain a battery charge level of around 50-60% (i.e., ORANGE) for storage.
129 +** This charge level is recommended to prevent battery damage, and should be checked every six months.
130 +** Nodes should //__not be stored at full-charge (GREEN), or 0-charge (RED).__//
131 +** Storage at 0-charge damages lithium batteries**.**
132 +* **SoC for Transport:**
133 +** Charge levels for transport will be advised by the freighter. The required SoC will depend on volume and transport method (air, land, sea).
88 88  
89 89  (((
90 -== **6. Data Sharing and Metadata Creation** ==
136 +== 6. Data Sharing and Metadata Creation ==
91 91  )))
92 92  
93 93  **GPS Data**:
94 94  
95 -* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
141 +* Ensure you have __carefully documented__ precise lat/lon locations for each station.
96 96  
97 97  **Photo Sharing**:
98 98  
... ... @@ -100,9 +100,9 @@
100 100  
101 101  **Metadata File**:
102 102  
103 -* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]].
149 +* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.
104 104  
105 -== **7. Additional Best Practices** ==
151 +== 7. Additional Best Practices ==
106 106  
107 107  * **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
108 108  
... ... @@ -157,32 +157,34 @@
157 157  = **Charging Procedure for Seismic Nodes** =
158 158  
159 159  (((
160 -== **1. Preparation for Charging**: ==
206 +== 1. Preparation for Charging: ==
161 161  
162 162  * Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
163 163  )))
164 164  
165 165  (((
166 -== **2. Disassembling the Node**: ==
212 +== 2. Disassembling the Node: ==
167 167  
168 -* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
214 +* For the IGU-16HR, remove the battery section (bottom half) from the sensor by unscrewing the spike section counter-clockwise.
169 169  )))
170 170  
171 171  (((
172 -== **3. Setting Nodes in the Charging Box**: ==
218 +== 3. Setting Nodes in the Charging Box: ==
173 173  
174 -* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
220 +* Connect to a safe indoor power supply, and turn on (red rocker switch).
221 +* Charging will begin automatically when nodes are inserted in the charging rack.
222 +* Place IGU-16HR battery sections upside-down in the rack, oriented with the terminal connectors.
175 175  )))
176 176  
177 177  (((
178 -== **4. Monitoring the Charging Process**: ==
226 +== 4. Monitoring the Charging Process: ==
179 179  
180 -* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
181 -* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
228 +* Lights adjacent to the batteries will illuminate, indicating that charging is underway.
229 +* Observe the transition of the lights from steady RED to ORANGE, then GREEN, and finally to FLASHING GREEN. A flashing green light indicates the batteries are fully charged.
182 182  )))
183 183  
184 184  (((
185 -== **5. Updating Charge Status**: ==
233 +== 5. Updating Charge Status: ==
186 186  
187 187  * During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
188 188  * This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
... ... @@ -193,14 +193,29 @@
193 193  
194 194  
195 195  
196 -[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
244 +{{{
245 + }}}
197 197  
198 198  ----
199 199  
200 200  = **Downloading and Converting Seismic Data to MiniSeed Format** =
201 201  
202 -== **Node Registration and Software Setup** ==
251 +(% class="wikigeneratedid" %)
252 +SmartSolo provides the following powerpoint for SmartSolo node programming and operation. Note that ANSIR only uses a portion of their process for our own uses: [[https:~~/~~/nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf>>url:https://nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf]]
203 203  
254 +== Connection tips: ==
255 +
256 +Connecting SmartSolo nodes to their harvesters and having SoloLite recognise them can be a bit tricky, here are some tricks to help register and program them easier:
257 +
258 +* Place the node on the harvester gently, then firmly press it down onto the pins.
259 +* Place all nodes onto the harvester before trying any troubleshooting, as they may not show up while the SoloLite software is running. Once all are connected, try restarting the software for them to be recognised.
260 +* If a node is refusing to connect, try it with another slot. It is easiest if you place all 16 nodes on the harvester, and swap any nodes that refuse to connect with each other.
261 +* Nodes will likely not show up in the order that they should, though this is not an issue. E.g, a node in slot 6 on the harvester may show up in port 13 in the SoloLite software. Annoying, but it doesn't matter so long as you keep track of what's been harvested!
262 +
263 +
264 +
265 +== Node Registration and Software Setup ==
266 +
204 204  1. (((
205 205  **Registering Nodes in the System**:
206 206  
... ... @@ -217,8 +217,29 @@
217 217  * Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
218 218  )))
219 219  
220 -== **Data Downloading Process** ==
283 +== File structure ==
221 221  
285 +There are essentially three main folders where relevant PROSPECT and PROJECT DATA is stored. Individual projects will be found as subfolders in these.
286 +
287 +=== SOLOLITE ===
288 +
289 +This folder stores SoloLite config files and parameters. Nothing too important stored here, you can always start over and re-create this.
290 +
291 +=== DCCDATA ===
292 +
293 +This folder stores the RAW data you have harvested from the nodes. The data will still be on the nodes (unless you erased it) in case of emergency, but regardless, this is the folder you want to back up and save somewhere.
294 +
295 +If you had a weird time harvesting a node, you can always manually copy it as if it were a USB stick and place it into this folder manually. The structure is: //C:/DCCDATA/prospect_name/project_name/SERIALNUMBER/label(usually a timestamp but can be anything)//
296 +
297 +Then in the SoloLite software, go to tools > Reanalyze Seismic Data
298 +
299 +=== SOLODATA ===
300 +
301 +This folder stores **exported** (e.g. miniseed) data. It is structured similarly. If your DCCDATA is intact, this can always be re-created if need be.
302 +
303 +
304 +== Data Downloading Process ==
305 +
222 222  1. (((
223 223  **Initiating Data Download**:
224 224  
... ... @@ -235,14 +235,48 @@
235 235  * Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
236 236  * (% class="box warningmessage" %)
237 237  (((
238 -* **Ensure to export data as "COUNTS", not "mV".**
322 +* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**
239 239  
240 -* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db for short period nodes (a factor of 15.848932), and 6db for broadband nodes).**
324 +* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**
241 241  )))
242 242  )))
243 243  
244 -== **Handling Nodes During Download** ==
328 +== Smart Solo IGU-16HR Polarity Notice ==
245 245  
330 +See [[https:~~/~~/auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug>>https://auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodeZPolaritybug]] for discussion. If data is headed to AusPass, we prefer to invert the IGU-16HR channel data manually rather than in the SoloLite software or inverting the response metadata.
331 +
332 +**The BD3C-5 data does not require a polarity inversion.**
333 +
334 +== 18 Leap Second bug ==
335 +
336 +Not so much a //bug// as much as "a thing that can happen if your SoloLite installation is corrupted". If you notice your data has large constant time offsets, you should suspect that the number of leap seconds has not been accounted properly. There is a file "smartsoloconfig.xml" that needs to be present in "C:\SmartSoloApps SoloLite" (e.g. the main program directory) that dictates the leap second offset for the last two data ranges. Since 2017-01-01, this is 18 seconds. At some point in the next few years it will be 19 seconds.
337 +
338 +If this file is missing, just create a new one structured like so, name it "smartsoloconfig.xml" and put it in your main program directory. Then, Reanalyze your data (tools > Reanalyze seismic data) and your data should have the correct time. You can also do this manually, if you want. The offset is 18 seconds precisely.
339 +
340 +{{code language="none"}}
341 +<?xml version="1.0" encoding="UTF-8"?>
342 +<config>
343 + <leapsecond>
344 + <interval>
345 + <start_time>2017-01-01#00:00:00</start_time>
346 + <end_time>2999-12-31#23:59:59</end_time>
347 + <second>18</second>
348 + </interval>
349 + <interval>
350 + <start_time>1970-01-01#00:00:00</start_time>
351 + <end_time>2017-01-01#00:00:00</end_time>
352 + <second>17</second>
353 + </interval>
354 + </leapsecond>
355 + <GPS_distance_threshold_degree>
356 + 4e-5
357 + </GPS_distance_threshold_degree>
358 +</config>
359 +{{/code}}
360 +
361 +
362 +== Handling Nodes During Download ==
363 +
246 246  1. (((
247 247  **Monitoring Download Indicators**:
248 248  
... ... @@ -258,6 +258,7 @@
258 258  * **Use fast external hard drives to avoid limitations in data harvesting.**
259 259  
260 260  * **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
379 +* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
261 261  )))
262 262  )))
263 263  1. (((
... ... @@ -297,26 +297,23 @@
297 297  
298 298  = **Cleaning** =
299 299  
300 -**Procedure for Seismic Nodes:**
419 +When assembled, the nodes are water resistant but not submersible. They can handle a good spray and wipe-down. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
301 301  
302 -Top half:
303 -
304 -Bottom half: The metal spikes on the bottom half of the nodes can be cleaned using a wire brush, though should still be wiped down for dust afterwards.
305 -
306 -
307 307  = **Weights (for shipping)** =
308 308  
309 309  The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
310 310  
311 -1 bag + 6 SP (IGU-16HR) nodes: 18 kg
425 +1 bag + 6*IGU-16HR nodes: 18 kg
312 312  
313 -1 SP (IGU-16HR) data harvester: 21.5 kg
427 +1*IGU-16HR data harvester: 21.5 kg
314 314  
315 -1 SP (IGU-16HR) charger: 26.3 kg
429 +1*IGU-16HR charger: 26.3 kg
316 316  
317 -1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
431 +1*BD3C-5 charger (with and without 16 cables): 21 kg / 14.5 kg
318 318  
319 -1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
433 +1 case + 5*BD3C-5 nodes: 22 kg (aggregate battery weight <5kg, 168Wh)
434 +
435 +1 case + 6*BD3C-5 nodes: 25 kg (aggregate battery weight >5kg, 168Wh)
320 320  )))
321 321  
322 322  (% class="col-xs-12 col-sm-4" %)
... ... @@ -340,7 +340,7 @@
340 340  
341 341  |(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
342 342  |(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
343 -|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
459 +|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)Φ158 x160mm(H)
344 344  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
345 345  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
346 346  |(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
... ... @@ -352,7 +352,7 @@
352 352  
353 353  (% class="box" %)
354 354  (((
355 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
471 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
356 356  
357 357  [[image:smartsolo node.jpg]]
358 358  
... ... @@ -359,8 +359,8 @@
359 359  [[image:smartsolo node 2.jpg]]
360 360  
361 361  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
362 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
363 -|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
478 +|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)76.7 V/m/s
479 +|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm(H)
364 364  |(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
365 365  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
366 366  |(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
... ... @@ -370,6 +370,99 @@
370 370  )))
371 371  )))
372 372  
489 +(% class="box" %)
490 +(((
373 373  
492 +
493 += SmartSolo [[IGU-16>>url:https://smartsolo.com/cp-3.html]]1C =
494 +
495 +
496 +[[image:Screenshot 2025-08-01 161027.png]]
497 +
498 +|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 413Hz
499 +|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)80 V/m/s
500 +|(% style="width:187px" %)**Size (without spike)**|(% style="width:224px" %)95mm(L) × 103mm(W) × 118mm(H)
501 +|(% style="width:187px" %)**Weight**|(% style="width:224px" %)1.1 kg
502 +|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)8 Gb
503 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
504 +Lithium-ion battery contained in equipment (38.48 Wh)
505 +
506 +UN3481 PI967 S2
374 374  )))
375 375  )))
509 +
510 +(% class="box" %)
511 +(((
512 += SmartSolo BD3C-16 Portable Battery Charger =
513 +
514 +[[image:20250729_125049.jpg]]
515 +
516 +|**Dimensions (LxHxW)**|558 x 357 x 300mm
517 +|**Input rating**|100-210V - 50/60Hz
518 +|**Power**|1000W
519 +|**Weight**|14.5kg
520 +|**Weight with cables**|21kg
521 +)))
522 +
523 +(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
524 +(((
525 += SmartSolo IGU-16 Portable Data Harvester =
526 +
527 +[[image:20250729_124747.jpg]]
528 +
529 +|**Dimensions (LxHxW)**|625 x 500 x 366mm
530 +|**Input rating**|100-210V - 50/60Hz
531 +|**Power**|100W
532 +|**Weight**|21.5 - 24kg
533 +|**Slots no.**|16
534 +|**Download Speed**|20MB/sec/slot
535 +)))
536 +
537 +(% class="box" %)
538 +(((
539 += SmartSolo IGU-16 Portable Battery Charger =
540 +
541 +[[image:20250729_124644.jpg]]
542 +
543 +|**Dimensions (LxHxW)**|625 x 500 x 366mm
544 +|**Input rating**|100-210V - 50/60Hz
545 +|**Power**|640W
546 +|**Weight**|26.3kg
547 +|**Slots no.**|16
548 +)))
549 +
550 +(% class="box" %)
551 +(((
552 += SmartSolo BD3C-5 Carry Case =
553 +
554 +[[image:20250729_124957.jpg]]
555 +
556 +
557 +|**Dimensions (LxHxW)**|590 x 225 x 405mm
558 +|**Weight**|8.2kg
559 +|**Slots no.**|6
560 +)))
561 +
562 +(% class="box" %)
563 +(((
564 += SmartSolo IGU-16 3C Carry Bag =
565 +
566 +[[image:20250729_124502.jpg]]
567 +
568 +|**Dimensions (LxHxW)**|230 x 340 x 310mm
569 +|**Weight**|3.6kg
570 +|**Slots no.**|6
571 +)))
572 +
573 +(% class="box" %)
574 +(((
575 += SmartSolo IGU-16 1C Carry Bag =
576 +
577 +[[image:20250729_124558.jpg]]
578 +
579 +|**Dimensions (LxHxW)**|225 x 200 x 550mm
580 +|**Weight**|
581 +|**Slots no.**|6
582 +)))
583 +)))
584 +)))
20250729_124502.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +457.6 KB
Content
5Hz_node_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.KB
Size
... ... @@ -1,0 +1,1 @@
1 +109.8 KB
Content
5S_node_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.KB
Size
... ... @@ -1,0 +1,1 @@
1 +114.2 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +106.7 KB
Content
Screenshot 2025-08-01 161027.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +82.8 KB
Content
XWiki.XWikiRights[0]
Allow/Deny
... ... @@ -1,0 +1,1 @@
1 +Allow
Groups
... ... @@ -1,0 +1,1 @@
1 +XWiki.XWikiAllGroup
Levels
... ... @@ -1,0 +1,1 @@
1 +comment
XWiki.XWikiRights[1]
Allow/Deny
... ... @@ -1,0 +1,1 @@
1 +Allow
Levels
... ... @@ -1,0 +1,1 @@
1 +comment
Users
... ... @@ -1,0 +1,1 @@
1 +XWiki.XWikiGuest