Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 43.1
edited by robert
on 2024/05/14 13:49
Change comment: There is no comment for this version
To version 15.1
edited by Jack Dent
on 2024/01/15 08:49
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.robert
1 +XWiki.JackD
Content
... ... @@ -2,324 +2,191 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -= **Node Types** =
5 += SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
6 6  
7 -ANSIR carry two types of three-channel nodes
7 +blahblah
8 8  
9 -* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 -* **SmartSolo BD3C-5 (5 Second Broad-Band)**
9 +== Sub-paragraph ==
11 11  
12 -Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
13 13  
12 +== ==
14 14  
15 -----
16 16  
17 -= **Programming Defaults** =
15 += Smart Solo BD3C-5 (5 second) Broad-Band Node =
18 18  
19 -ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
17 +Lorem
20 20  
19 +[[image:1705196270090-364.png]]
21 21  
22 -== **Pre-Fieldwork Preparation** ==
23 23  
24 -(% class="box infomessage" %)
25 -(((
26 -(% class="box warningmessage" %)
27 -(((
28 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
22 +== GPS Considerations ==
29 29  
30 -**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
31 -)))
32 -)))
24 +The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
33 33  
34 -= **Installation** =
26 += Keeping the Instruments Clean =
35 35  
36 -=== **1- Logbook documentation** ===
28 +Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
37 37  
38 -(((
39 -**Essential Details**: Record the following in a logbook:
40 40  
41 -* Station name
42 -* Latitude and longitude
43 -* Names of team members present
44 -* Date and local time of installation
45 -* Serial number (SN) of the sensor
46 -* Detailed notes on the site conditions and setup
31 += Charge Time, Instrument Life, and Charge During Storage & Shipping =
47 47  
48 -=== **2- Node Placement** ===
49 -)))
33 +Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
50 50  
51 -**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
35 +Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
52 52  
53 -**Site Analysis**:
54 54  
55 -* **Take compass measurements away from the sensor as it will affect your measurement.**
56 -* Take multiple photographs from various angles to document the site setup thoroughly.
57 -* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
38 += Best Practices and Guide =
58 58  
59 -=== **3- GPS Considerations** ===
40 +== Install ==
60 60  
61 -(% class="wikigeneratedid" %)
62 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. These nodes will not start recording without attaining a GPS lock and repeated attempts will excessively drain the battery.
42 +Logbook is required (used again for pick up & metadata creation)
63 63  
64 -=== **4- Visibility and Location Marking** ===
44 +- station name
65 65  
66 -**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
46 +- lat / long
67 67  
68 -**GPS Marking**:
48 +- team members
69 69  
70 -* Use a GPS device to mark the instrument's exact location.
71 -* Record this location in both your paper notes and the GPS device.
50 +- date and local time
72 72  
73 -=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5- Charge Time, Pre-Deployment & Post-Deployment**(%%) ===
52 +- SN of sensor
74 74  
75 -* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
76 -* **Pre-Deployment Charging**:
77 -** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
54 +- notes on site
78 78  
79 -* **Operational Duration**:
80 -** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
56 +Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
81 81  
82 -* **Post-Retrieval Charging**:
83 -** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
84 -* **Storage and Shipping Charge Level**:
85 -** Maintain a battery charge level of around 50-60% for both storage and shipping purposes.
86 -** This charge level is recommended to prevent battery damage and is safe for transportation.
87 -** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
58 +Take compass measurement away from node and fences [make sure to adjust inclination angle]
88 88  
89 -=== ===
60 +Take many photos from the site from different angles 
90 90  
91 -(((
92 -=== **6- Data Sharing and Metadata Creation** ===
93 -)))
62 +Add a precise site description to the notes such as distances and orientations from landmarks 
94 94  
95 -**GPS Data**:
64 +It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
96 96  
97 -* Download the GPS file to a laptop. (???)
98 -* Share this file on a drive accessible to all team members for uniform understanding of node locations.
66 +Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
99 99  
100 -**Photo Sharing**:
68 +Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
101 101  
102 -* Upload site photos to a shared platform (OneDrive, Dropbox, etc.).
103 -* Integrating photos into Google Maps or Google Earth can be particularly beneficial for easy location referencing.
70 +Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
104 104  
105 -**Metadata File**:
72 +Create metadata .xml file
106 106  
107 -* Create and organize metadata via the ANU metadata standard (~*~*add example)
108 108  
109 -=== **7- Additional Best Practices** ===
75 +== Removing/Demob ==
110 110  
111 -* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
112 -* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass, and other equipment to ensure consistent and accurate data collection.
77 +Download and then use the GPS file to locate the node 
113 113  
114 -* (((
115 -==== **Keeping the Instruments Clean** ====
116 -)))
117 -* (((
118 -Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
119 -)))
79 +Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
120 120  
121 -----
122 122  
123 -=== **Seismic Station Demobilization and Documentation** ===
82 +Upload photos of the site  
124 124  
125 -1. (((
126 -**Preparation for Demobilization**:
84 +- station name
127 127  
128 -* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, clipboard, logbook, and compass ready in your tote bag.
129 -)))
130 -1. (((
131 -**Locating the instrument**:
86 +- latitude
132 132  
133 -* Use the downloaded GPS file to accurately locate the node for demobilization.
134 -* Import this KMZ file onto your phone for easy reference and location tracking.
135 -* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
136 -)))
137 -1. (((
138 -**Labeling Instruments for Demobilization**:
88 +- longitude
139 139  
140 -* Write the station name and the instrument’s serial number on a label.
141 -* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
142 -* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
143 -)))
144 -1. (((
145 -**Photographing the Setup Node**:
90 +- elevation
146 146  
147 -* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
148 -* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
149 -)))
150 -1. (((
151 -**Logging Demobilization Details**:
92 +* SN of sensor – SN of battery (optional)
93 +* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
152 152  
153 -* Use the field logbook to note the time of demobilization, serial numbers, and station name.
154 -* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
155 -)))
156 -1. (((
157 -**Final Checks and Equipment Removal**:
95 +Upload photos into Google Earth and on a shared drive
158 158  
159 -* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
160 -* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
97 +Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
161 161  
162 -
163 -)))
99 +Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
164 164  
165 -[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
101 +Take a photo of the entire setup node with the label on it + compass 
166 166  
167 -----
103 +Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
168 168  
169 -=== **Charging Procedure for Seismic Nodes** ===
170 170  
171 -1. (((
172 -**Preparation for Charging**:
106 +== Charging ==
173 173  
174 -* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
108 +Clean node prior to charging and harvesting the data
175 175  
176 -
177 -)))
178 -1. (((
179 -**Disassembling the Node**:
110 +Remove battery (and spike) from the sensor by twisting the spike part of the instrument
180 180  
181 -* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
112 +Set 16 nodes into the charging box (spikes up)
182 182  
183 -
184 -)))
185 -1. (((
186 -**Setting Nodes in the Charging Box**:
114 +Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
187 187  
188 -* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
116 +This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
189 189  
190 -
191 -)))
192 -1. (((
193 -**Monitoring the Charging Process**:
118 +[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
194 194  
195 -* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
196 -* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
197 197  
198 -
199 -)))
200 -1. (((
201 -**Updating Charge Status**:
202 202  
203 -* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
204 -* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
205 -)))
122 +== Downloading and Converting Data to MiniSeed ==
206 206  
207 -[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
208 208  
125 +The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
209 209  
127 +[[image:1705195543887-977.png]]
210 210  
211 211  
212 -[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
130 +Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
213 213  
214 -----
132 +[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
215 215  
216 -=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
217 217  
218 -==== **Node Registration and Software Setup** ====
135 +Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
219 219  
220 -1. (((
221 -**Registering Nodes in the System**:
137 +[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
222 222  
223 -* To begin, register the nodes in the system so the software can recognize them.
224 -* Navigate to the installation folder of “SmartSoloApps SoloLite”.
225 -* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
226 -* To avoid double registration, replace the file each time you register a new node.
227 -)))
228 -1. (((
229 -**Creating a New Project in SoloLite**:
139 +At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
230 230  
231 -* Open the “SoloLite” software.
232 -* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
233 -* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
141 +(% class="box warningmessage" %)
142 +(((
143 +**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
234 234  )))
235 235  
236 -==== **Data Downloading Process** ====
237 -
238 -1. (((
239 -**Initiating Data Download**:
240 -
241 -* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
242 -* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
243 -* Select all nodes and right-click to “force download”. This starts the download process.
244 -* Completed downloads will appear as new folders in the Downloaded Data panel.
245 -)))
246 -1. (((
247 -**Exporting Data in Readable Format**:
248 -
249 -* Go to the “Tool” menu and select “export seismic data”.
250 -* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
251 -* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
252 -* (% class="box warningmessage" %)
146 +(% class="box warningmessage" %)
253 253  (((
254 -* **Ensure to export data as "COUNTS", not "mV".**
255 -
256 -* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db (a factor of 15.848932).**
148 +**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
257 257  )))
258 -)))
259 259  
260 -==== **Handling Nodes During Download** ====
151 +A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
261 261  
262 -1. (((
263 -**Monitoring Download Indicators**:
153 +Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
264 264  
265 -* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
266 -* Disconnect nodes properly before unplugging anything.
267 -* Be cautious: if the laptop enters sleep mode, the download will pause.
268 -)))
269 -1. (((
270 -//**Investment in Storage Hardware**~://
155 +[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
271 271  
272 -* (% class="box warningmessage" %)
273 -(((
274 -* **Use fast external hard drives to avoid limitations in data harvesting.**
157 +When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
275 275  
276 -* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
159 +(% class="box infomessage" %)
160 +(((
161 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
277 277  )))
278 -)))
279 -1. (((
280 -**Metadata and Time Settings**:
281 281  
282 -* Ensure all metadata is saved with the file.
283 -* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
284 -)))
285 -1. (((
286 -**Finalizing the Download**:
164 +When downloading, ensure that all metadata is saved along with the file.
287 287  
288 -* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
166 +Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
289 289  
290 -
291 -)))
168 +//Once downloaded, mark the "D" box on your temporary labels!//
292 292  
293 -[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
170 +== Converting data ==
294 294  
172 +Check the data all have been converted to miniseed correctly 
295 295  
174 +– 3 files per station per day 
296 296  
297 -[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
176 +* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
177 +* ~~ 5 Gb / node / month
298 298  
179 +//Tick ‘R’ box on the node label//
299 299  
300 300  
182 +== Cleaning ==
301 301  
302 -[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
184 +If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
303 303  
304 -
305 -
306 -[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
307 -
308 -
309 -
310 -[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
311 -
312 -----
313 -
314 -=== **Cleaning** ===
315 -
316 -**Procedure for Seismic Nodes:**
317 -
318 -* If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
319 -
320 -= =
186 +
321 321  )))
322 322  
189 +
323 323  (% class="col-xs-12 col-sm-4" %)
324 324  (((
325 325  (% class="box" %)
... ... @@ -327,7 +327,10 @@
327 327  **Contents**
328 328  
329 329  (% class="wikitoc" %)
330 -* [[Smart Solo BD3C-5 (5 second) B>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
197 +* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
198 +** [[Sub-paragraph>>path:#HSub-paragraph]]
199 +** [[ >>path:#H]]
200 +* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
331 331  ** [[GPS Considerations>>path:#HGPSConsiderations]]
332 332  * [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
333 333  * [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
... ... @@ -347,8 +347,6 @@
347 347  
348 348  [[image:Smartsolo IGU BD3C 5 (2).jpg]]
349 349  
350 -[[image:smartsolo.jpg]]
351 -
352 352  |(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
353 353  |(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
354 354  |(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
... ... @@ -361,16 +361,12 @@
361 361  (((
362 362  = SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
363 363  
364 -[[image:smartsolo node.jpg]]
365 -
366 -[[image:smartsolo node 2.jpg]]
367 -
368 368  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
369 369  |(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
370 370  |(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
371 371  |(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
372 372  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
373 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Lithium ion XXAh
237 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
374 374  )))
375 375  
376 376  
1706153266647-145.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -839.4 KB
Content
smartsolo node 2.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -1.0 MB
Content
smartsolo node.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -1.1 MB
Content
smartsolo.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -1.0 MB
Content