Changes for page SmartSolo Node Seismometers

Last modified by robert on 2025/06/16 07:51

From 37.1 to 37.2 From 56.1 to 57.1

From version 37.2

edited by Sima Mousavi
on 2024/01/25 14:31

Change comment: There is no comment for this version

To version 56.1

edited by robert
on 2025/06/15 17:48

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (3 modified, 0 added, 0 removed)
Attachments (0 modified, 2 added, 0 removed)
- 1706153556166-231.jpeg
- example_metadata.txt

Details

Page properties

Title

@@ -1,1 +1,1 @@
--SmartSolo Nodes
++SmartSolo Node Seismometers

Author

@@ -1,1 +1,1 @@
--XWiki.sima
++XWiki.robert

Content

@@ -2,15 +2,25 @@
  (((
  (% class="col-xs-12 col-sm-8" %)
  (((
--= **Node Setup** =
++= **Node Types** =
--Short term (~~30 day) battery powered nodes. The default gain should be 24 db for the 16HR-3C and 6 db for the BD3C-5
++ANSIR carry two types of three-channel nodes
++* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
++* **SmartSolo BD3C-5 (5 Second Broad-Band)**
--~*~**this needs to be reformatted
++Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
--== **Pre-Fieldwork Preparation** ==
++----
++
++= **Programming Defaults** =
++
++ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
++
++
++= **Fieldwork Preparation** =
++
  (% class="box infomessage" %)
  (((
  (% class="box warningmessage" %)
@@ -17,13 +17,13 @@
  (((
  **INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
--**Plan on 1 Tb to store ALL data for 50 nodes @ 250 Hz and a single ~~30 day occupation**
++**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
  )))
  )))
  = **Installation** =
--=== **1- Logbook documentation** ===
++== **1. Logbook documentation** ==
  (((
  **Essential Details**: Record the following in a logbook:
@@ -35,23 +35,23 @@
  * Serial number (SN) of the sensor
  * Detailed notes on the site conditions and setup
--=== **2- Node Placement** ===
++== **2. Node Placement** ==
  )))
--**Protection**: Place nodes inside thick, landfill biodegradable plastic bags for environmental protection.
++**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
  **Site Analysis**:
--* Conduct compass measurements away from the node and metallic structures, adjusting for inclination angle.
++* **Take compass measurements away from the sensor as it will affect your measurement.**
  * Take multiple photographs from various angles to document the site setup thoroughly.
  * Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
--=== **3- GPS Considerations** ===
++== **3. GPS Considerations** ==
  (% class="wikigeneratedid" %)
--The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
++The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
--=== **4- Visibility and Location Marking** ===
++== **4. Visibility and Location Marking** ==
  **Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
@@ -60,63 +60,50 @@
  * Use a GPS device to mark the instrument's exact location.
  * Record this location in both your paper notes and the GPS device.
--=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5- Charge Time, Pre-Deployment & Post-Deployment**(%%) ===
++== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5. Charge Time, Pre-Deployment & Post-Deployment**(%%) ==
  * **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
  * **Pre-Deployment Charging**:
--** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge right before deployment.
++** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
  * **Operational Duration**:
--** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle.
++** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
  * **Post-Retrieval Charging**:
--** Do not store the instruments with completely drained batteries.
--** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) for optimal battery health.
--
++** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
  * **Storage and Shipping Charge Level**:
--** Maintain a battery charge level of around 50-60% for both storage and shipping purposes.
++** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
  ** This charge level is recommended to prevent battery damage and is safe for transportation.
++** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
--===   ===
--
--* (((
--=== **6- Data Sharing and Metadata Creation** ===
++(((
++== **6. Data Sharing and Metadata Creation** ==
  )))
  **GPS Data**:
--* Download the GPS file to a laptop.
--* Share this file on a drive accessible to all team members for uniform understanding of node locations.
++* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
  **Photo Sharing**:
--* Upload site photos to a shared platform (OneDrive, Dropbox, etc.).
--* Integrating photos into Google Maps or Google Earth can be particularly beneficial for easy location referencing.
++* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
  **Metadata File**:
--* Create a metadata XML file for each node, which is essential for data organisation and future reference.
++* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]].
--=== **7- Additional Best Practices** ===
++== **7. Additional Best Practices** ==
--* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
--* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass, and other equipment to ensure consistent and accurate data collection.
++* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
--* (((
--==== **Keeping the Instruments Clean** ====
--)))
--* (((
--Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
--)))
--
  ----
--=== **Seismic Station Demobilization and Documentation** ===
++= **Seismic Station Demobilization and Documentation** =
 . (((
  **Preparation for Demobilization**:
--* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, clipboard, logbook, and compass ready in your tote bag.
++* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
  )))
 . (((
  **Locating the instrument**:
@@ -128,7 +128,7 @@
 . (((
  **Labeling Instruments for Demobilization**:
--* Write the station name and the instrument’s serial number on a label.
++* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
  * Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
  * Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
  )))
@@ -149,54 +149,60 @@
  * Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
  * Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
++
++
  )))
--[[image:blob:https://anu365-my.sharepoint.com/aba1fadc-c966-4177-9f2c-7cbd734bff46]] [[image:blob:https://anu365-my.sharepoint.com/aba1fadc-c966-4177-9f2c-7cbd734bff46]]
++[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
  ----
--=== **Charging Procedure for Seismic Nodes** ===
++= **Charging Procedure for Seismic Nodes** =
--1. (((
--**Preparation for Charging**:
++(((
++== **1. Preparation for Charging**: ==
  * Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
  )))
--1. (((
--**Disassembling the Node**:
--* Carefully remove the battery and the spike from the sensor. This is typically done by twisting the spike part of the instrument to release these components.
++(((
++== **2. Disassembling the Node**: ==
++
++* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
  )))
--1. (((
--**Setting Nodes in the Charging Box**:
--* Place up to 16 nodes into the charging box, arranging them with the spikes pointing upwards. This configuration is essential for proper connection and efficient charging.
++(((
++== **3. Setting Nodes in the Charging Box**: ==
++
++* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
  )))
--1. (((
--**Monitoring the Charging Process**:
--* Once the nodes are set in the charging box and the charging process begins, red lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
--* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged.
++(((
++== **4. Monitoring the Charging Process**: ==
++
++* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
++* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
  )))
--1. (((
--**Updating Charge Status**:
++(((
++== **5. Updating Charge Status**: ==
++
  * During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
  * This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
  )))
--[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
++[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
--[[image:1706153354750-415.png]]
++[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
  ----
--=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
++= **Downloading and Converting Seismic Data to MiniSeed Format** =
--==== **Node Registration and Software Setup** ====
++== **Node Registration and Software Setup** ==
 . (((
  **Registering Nodes in the System**:
@@ -214,7 +214,7 @@
  * Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
  )))
--==== **Data Downloading Process** ====
++== **Data Downloading Process** ==
 . (((
  **Initiating Data Download**:
@@ -234,11 +234,11 @@
  (((
  * **Ensure to export data as "COUNTS", not "mV".**
--* **Set "Remove Gain" to the same decibel gain as during programming (ANU usually sets this to 18 db, but double-check).**
++* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db for short period nodes (a factor of 15.848932), and 6db for broadband nodes).**
  )))
  )))
--==== **Handling Nodes During Download** ====
++== **Handling Nodes During Download** ==
 . (((
  **Monitoring Download Indicators**:
@@ -271,214 +271,51 @@
  )))
--[[image:1706153266647-145.png]]
++[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
--[[Caption>>image:1705195543887-977.png]]
--[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
++[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
--[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
++[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
--[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
------
++[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
--=== **Cleaning** ===
--**Procedure for Seismic Nodes:**
--* If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
++[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
--=   =
++----
--= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
++= **Cleaning** =
--blahblah
++**Procedure for Seismic Nodes:**
--== Sub-paragraph ==
++Top half:
++Bottom half: The metal spikes on the bottom half of the nodes can be cleaned using a wire brush, though should still be wiped down for dust afterwards.
--== [[image:1705196270090-364.png]] ==
++= **Weights (for shipping)** =
--= Smart Solo BD3C-5 (5 second) Broad-Band Node =
++The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
--Lorem
++1 bag + 6 SP (IGU-16HR) nodes: 18 kg
++1 SP (IGU-16HR) data harvester: 21.5 kg
--== GPS Considerations ==
++1 SP (IGU-16HR) charger: 26.3 kg
--The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
++1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
--= Keeping the Instruments Clean =
--
--Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
--
--
--= Charge Time, Instrument Life, and Charge During Storage & Shipping =
--
--Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
--
--Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
--
--
--= Best Practices and Guide =
--
--== Install ==
--
--Logbook is required (used again for pick up & metadata creation)
--
--- station name
--
--- lat / long
--
--- team members
--
--- date and local time
--
--- SN of sensor
--
--- notes on site
--
--Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
--
--Take compass measurement away from node and fences [make sure to adjust inclination angle]
--
--Take many photos from the site from different angles
--
--Add a precise site description to the notes such as distances and orientations from landmarks
--
--It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
--
--Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
--
--Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
--
--Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
--
--Create metadata .xml file
--
--
--== Removing/Demob ==
--
--Download and then use the GPS file to locate the node
--
--Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.
--
--
--Upload photos of the site
--
--- station name
--
--- latitude
--
--- longitude
--
--- elevation
--
--* SN of sensor – SN of battery (optional)
--* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
--
--Upload photos into Google Earth and on a shared drive
--
--Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!).
--
--Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
--
--Take a photo of the entire setup node with the label on it + compass
--
--Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
--
--[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
--
--
--== Charging ==
--
--Clean node prior to charging and harvesting the data
--
--Remove battery (and spike) from the sensor by twisting the spike part of the instrument
--
--Set 16 nodes into the charging box (spikes up)
--
--Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
--
--This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
--
--
--
--== Downloading and Converting Data to MiniSeed ==
--
--
--The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
--
--[[image:1705195543887-977.png]]
--
--
--Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
--
--[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
--
--
--Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
--
--[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
--
--At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
--
--(% class="box warningmessage" %)
--(((
--**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
++1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
  )))
--(% class="box warningmessage" %)
--(((
--**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
--)))
--
--A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
--
--Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
--
--[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
--
--When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
--
--(% class="box infomessage" %)
--(((
--**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
--)))
--
--When downloading, ensure that all metadata is saved along with the file.
--
--Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
--
--//Once downloaded, mark the "D" box on your temporary labels!//
--
--== Converting data ==
--
--Check the data all have been converted to miniseed correctly
--
--– 3 files per station per day
--
--* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
--* ~~ 5 Gb / node / month
--
--//Tick ‘R’ box on the node label//
--
--
--== Cleaning ==
--
--If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
--
--
--)))
--
--
  (% class="col-xs-12 col-sm-4" %)
  (((
  (% class="box" %)
@@ -485,24 +485,11 @@
  (((
  **Contents**
--(% class="wikitoc" %)
--* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
--** [[Sub-paragraph>>path:#HSub-paragraph]]
--** [[ >>path:#H]]
--* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
--** [[GPS Considerations>>path:#HGPSConsiderations]]
--* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
--* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
--* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
--** [[Install>>path:#HInstall]]
--** [[Removing/Demob>>path:#HRemoving2FDemob]]
--** [[Charging>>path:#HCharging]]
--** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
--** [[Converting data>>path:#HConvertingdata]]
--** [[Cleaning>>path:#HCleaning]]
++{{toc/}}
++
++
  )))
--
  (% class="box" %)
  (((
  = SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
@@ -516,8 +516,12 @@
  |(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
--|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
++|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
++Lithium-ion battery contained in equipment (168.84 Wh)
++
++UN3481 PI967 S1
  )))
++)))
  (% class="box" %)
  (((
@@ -530,10 +530,14 @@
  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
  |(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
  |(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
--|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.3 kg
++|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
--|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
++|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
++Lithium-ion battery contained in equipment (96.48 Wh)
++
++UN3481 PI967 S2
  )))
++)))
  )))

1706153556166-231.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+839.4 KB

Content

example_metadata.txt

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.robert

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.7 KB

Content

@@ -1,0 +1,46 @@
++# AKL-HR Node Array (AHNA) code X5
++CITE: Name, Name, and Name. (2023). A Node Array [Data set]. International Federation of Digital Seismograph Networks. https://doi.org/10.7914/8jxr-7029
++
++#SITE     START             END          LAT      LONG      ELEV SPS    RECORDER 	S/N   	SENSOR     S/N     	  PROPERTY,LOCALITY,COUNTRY         COMMENTS
++
++# INSTALL
++AKL01 20-05-2023T00:00 30-06-2023T00:00 -37.0471 175.5245   75   250   SSNODE_C 590001950 SSNODE_5S 590001950    "Te Puru,Hauraki,NZ"
++AKL02 20-05-2023T00:00 30-06-2023T00:00 -36.7476 175.5026   70   250   SSNODE_C 590001943 SSNODE_5S 590001943    "Coromandel Town,Hauraki,NZ"
++AKL03 20-05-2023T00:00 30-06-2023T00:00 -36.9694 175.5020   98   250   SSNODE_C 590002068 SSNODE_5S 590002068    "Te Mata,Hauraki,NZ"
++AKL05 19-05-2023T19:00 22-02-2023T00:00 -36.5996 174.3312   102  250   SSNODE_C 590001957 SSNODE_5S 590001957    "South Head South,Auckland,NZ" "site was disturbed"
++AKL06 19-05-2023T19:00 30-06-2023T00:00 -37.2459 175.3426   34   250   SSNODE_C 590001930 SSNODE_5S 590001930    "Back Miranda,Auckland,NZ"
++AKB05 02-05-2023T00:37 30-06-2023T00:00 -36.6651 175.4800   63   250   TSAWR    TS085A    TRILL120  4875         "Colville,Hauraki,NZ"
++
++# SERVICE 1
++AKL05 22-02-2023T00:00 30-06-2023T00:00 -36.5996 174.3312   102  250   SSNODE_C 590001999 SSNODE_.2S 590001999    "South Head South,Auckland,NZ" "swapped node to shortperiod"
++
++
++
++
++################### ANY LINE BEGINNING WITH # will be commented! Comments are good!
++
++
++# NOTES
++# the start/end time is not critical, but good to have. what IS critical are the times of instrument changes as this potentially affects response information
++# to mark equipment changes, add a new line with an updated start date (e.g. AKL05 above)
++# can use tabs or spaces, but spaces tend to look nicer. formatting ultimately doesn't matter too much so long as there is any sort of "white space" between the fields
++# if you don't know a serial number, put 999. if you don't know the elevation, put 0
++# for Nodes, put the same serial number for both Recoder and Sensor (since they are the same!)
++
++
++# EXAMPLE INSTRUMENT LABELS
++#LPR200 = ANU LPR-200 logger (beige box)
++#TSAWR = ANU TerraSAWR logger (yellow box)
++
++#TRILL120 = Trillium Compact 120s
++#TRILL20 = Trillium Compact 20s
++#TRILL120PH = Trillium Compact 120s PostHole
++#CMG6TD = Guralp 6TD
++#CMG3ESP = Guralp 3ESP
++#3DLITE = Lenarrtz 3D-LITE
++
++#SSNODE_C = output was in COUNTS (there is also SSNODE_MV, if you (accidentally!) output to millivolts etc)
++#SSNODE_5S = broadband (can also use SSNODE_BB)
++#SSNODE_.2S = shortperiod (can also use SSNODE_SP)
++
++#it doesn't matter too much what you use for equipment labels, so long as they are consistent and otherwise defined somewhere in the comments!

Changes for page SmartSolo Node Seismometers

Summary

Details

Applications

Navigation

Need help?