Changes for page SmartSolo Node Seismometers

Last modified by robert on 2025/06/16 07:51

From 24.1 to 23.1 From 37.1 to 36.2

From version 36.2

edited by Sima Mousavi
on 2024/01/25 11:48

Change comment: There is no comment for this version

To version 24.1

edited by Sima Mousavi
on 2024/01/24 16:27

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -79,9 +79,7 @@
  ===   ===
--* (((
  === **6- Data Sharing and Metadata Creation** ===
--)))
  **GPS Data**:
@@ -109,7 +109,7 @@
  Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
  )))
------
++=   =
  === **Seismic Station Demobilization and Documentation** ===
@@ -151,143 +151,20 @@
  * Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
  )))
------
--=== **Charging Procedure for Seismic Nodes** ===
--1. (((
--**Preparation for Charging**:
--* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
--)))
--1. (((
--**Disassembling the Node**:
--* Carefully remove the battery and the spike from the sensor. This is typically done by twisting the spike part of the instrument to release these components.
--)))
--1. (((
--**Setting Nodes in the Charging Box**:
--* Place up to 16 nodes into the charging box, arranging them with the spikes pointing upwards. This configuration is essential for proper connection and efficient charging.
--)))
--1. (((
--**Monitoring the Charging Process**:
--* Once the nodes are set in the charging box and the charging process begins, red lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
--* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged.
--)))
--1. (((
--**Updating Charge Status**:
--* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
--* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
--)))
--[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
------
--=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
--==== **Node Registration and Software Setup** ====
--1. (((
--**Registering Nodes in the System**:
--* To begin, register the nodes in the system so the software can recognize them.
--* Navigate to the installation folder of “SmartSoloApps SoloLite”.
--* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
--* To avoid double registration, replace the file each time you register a new node.
--)))
--1. (((
--**Creating a New Project in SoloLite**:
--
--* Open the “SoloLite” software.
--* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
--* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
--)))
--
--==== **Data Downloading Process** ====
--
--1. (((
--**Initiating Data Download**:
--
--* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
--* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
--* Select all nodes and right-click to “force download”. This starts the download process.
--* Completed downloads will appear as new folders in the Downloaded Data panel.
--)))
--1. (((
--**Exporting Data in Readable Format**:
--
--* Go to the “Tool” menu and select “export seismic data”.
--* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
--* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
--* (% class="box warningmessage" %)
--(((
--* **Ensure to export data as "COUNTS", not "mV".**
--
--* **Set "Remove Gain" to the same decibel gain as during programming (ANU usually sets this to 18 db, but double-check).**
--)))
--)))
--
--==== **Handling Nodes During Download** ====
--
--1. (((
--**Monitoring Download Indicators**:
--
--* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
--* Disconnect nodes properly before unplugging anything.
--* Be cautious: if the laptop enters sleep mode, the download will pause.
--)))
--1. (((
--//**Investment in Storage Hardware**~://
--
--* (% class="box warningmessage" %)
--(((
--* **Use fast external hard drives to avoid limitations in data harvesting.**
--
--* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
--)))
--)))
--1. (((
--**Metadata and Time Settings**:
--
--* Ensure all metadata is saved with the file.
--* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
--)))
--1. (((
--**Finalizing the Download**:
--
--* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
--
--
--)))
--
-- [[image:1705195543887-977.png]]
--
--
--[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
--
--
--
--[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
--
--
--
--[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
--
------
--
--=== **Cleaning** ===
--
--**Procedure for Seismic Nodes:**
--
--* If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
--
--=   =
--
  = SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
  blahblah
@@ -295,7 +295,7 @@
  == Sub-paragraph ==
--== [[image:1705196270090-364.png]] ==
++==   ==
  = Smart Solo BD3C-5 (5 second) Broad-Band Node =
@@ -302,7 +302,9 @@
  Lorem
++[[image:1705196270090-364.png]]
++
  == GPS Considerations ==
  The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
@@ -386,9 +386,7 @@
  Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
--[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
--
  == Charging ==
  Clean node prior to charging and harvesting the data
@@ -401,8 +401,10 @@
  This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
++[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
++
  == Downloading and Converting Data to MiniSeed ==

Changes for page SmartSolo Node Seismometers

Summary

Details

Applications

Navigation

Need help?