Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 20.1
edited by Sima Mousavi
on 2024/01/18 17:25
Change comment: There is no comment for this version
To version 41.1
edited by Sima Mousavi
on 2024/02/05 16:46
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -2,10 +2,26 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 += **SmartSolo Node Types and Procedures** =
6 +
7 +**SmartSolo Node Variants:**
8 +
9 +* **SmartSolo IGU 16HR 3C (5 Hz) Short Period Node**
10 +* **SmartSolo BD3C-5 (5-second) Broad-Band Node**
11 +
12 +The installation, demobilization, and data downloading procedures for both types of SmartSolo nodes – the IGU 16HR 3C Short Period Node and the BD3C-5 Broad-Band Node – are largely similar.
13 +
14 +This uniformity in process ensures ease of operation across different node types, allowing for a streamlined approach in fieldwork and data management.
15 +
16 +----
17 +
5 5  = **Node Setup** =
6 6  
7 -Short term (~~30 day) battery powered nodes
20 +Short term (~~30 day) battery powered nodes. The default gain should be 24 db for the 16HR-3C and 6 db for the BD3C-5
8 8  
22 +
23 +~*~**this needs to be reformatted
24 +
9 9  == **Pre-Fieldwork Preparation** ==
10 10  
11 11  (% class="box infomessage" %)
... ... @@ -12,7 +12,9 @@
12 12  (((
13 13  (% class="box warningmessage" %)
14 14  (((
15 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING **
31 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
32 +
33 +**Plan on 1 Tb to store ALL data for 50 nodes @ 250 Hz and a single ~~30 day occupation**
16 16  )))
17 17  )))
18 18  
... ... @@ -61,16 +61,13 @@
61 61  * **Pre-Deployment Charging**:
62 62  ** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge right before deployment.
63 63  
64 -
65 65  * **Operational Duration**:
66 66  ** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle.
67 67  
68 -
69 69  * **Post-Retrieval Charging**:
70 70  ** Do not store the instruments with completely drained batteries.
71 71  ** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) for optimal battery health.
72 72  
73 -
74 74  * **Storage and Shipping Charge Level**:
75 75  ** Maintain a battery charge level of around 50-60% for both storage and shipping purposes.
76 76  ** This charge level is recommended to prevent battery damage and is safe for transportation.
... ... @@ -77,9 +77,9 @@
77 77  
78 78  === ===
79 79  
80 -=== ===
81 -
95 +* (((
82 82  === **6- Data Sharing and Metadata Creation** ===
97 +)))
83 83  
84 84  **GPS Data**:
85 85  
... ... @@ -107,193 +107,200 @@
107 107  Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
108 108  )))
109 109  
110 -= =
125 +----
111 111  
112 -= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
127 +=== **Seismic Station Demobilization and Documentation** ===
113 113  
114 -blahblah
129 +1. (((
130 +**Preparation for Demobilization**:
115 115  
116 -== Sub-paragraph ==
132 +* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, clipboard, logbook, and compass ready in your tote bag.
133 +)))
134 +1. (((
135 +**Locating the instrument**:
117 117  
137 +* Use the downloaded GPS file to accurately locate the node for demobilization.
138 +* Import this KMZ file onto your phone for easy reference and location tracking.
139 +* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
140 +)))
141 +1. (((
142 +**Labeling Instruments for Demobilization**:
118 118  
119 -== ==
144 +* Write the station name and the instrument’s serial number on a label.
145 +* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
146 +* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
147 +)))
148 +1. (((
149 +**Photographing the Setup Node**:
120 120  
151 +* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
152 +* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
153 +)))
154 +1. (((
155 +**Logging Demobilization Details**:
121 121  
122 -= Smart Solo BD3C-5 (5 second) Broad-Band Node =
157 +* Use the field logbook to note the time of demobilization, serial numbers, and station name.
158 +* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
159 +)))
160 +1. (((
161 +**Final Checks and Equipment Removal**:
123 123  
124 -Lorem
163 +* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
164 +* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
125 125  
126 -[[image:1705196270090-364.png]]
166 +
167 +)))
127 127  
169 +[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
128 128  
129 -== GPS Considerations ==
171 +----
130 130  
131 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
173 +=== **Charging Procedure for Seismic Nodes** ===
132 132  
133 -= Keeping the Instruments Clean =
175 +1. (((
176 +**Preparation for Charging**:
134 134  
135 -Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
178 +* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
179 +)))
180 +1. (((
181 +**Disassembling the Node**:
136 136  
183 +* Carefully remove the battery and the spike from the sensor. This is typically done by twisting the spike part of the instrument to release these components.
184 +)))
185 +1. (((
186 +**Setting Nodes in the Charging Box**:
137 137  
138 -= Charge Time, Instrument Life, and Charge During Storage & Shipping =
188 +* Place up to 16 nodes into the charging box, arranging them with the spikes pointing upwards. This configuration is essential for proper connection and efficient charging.
189 +)))
190 +1. (((
191 +**Monitoring the Charging Process**:
139 139  
140 -Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
193 +* Once the nodes are set in the charging box and the charging process begins, red lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
194 +* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged.
195 +)))
196 +1. (((
197 +**Updating Charge Status**:
141 141  
142 -Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
199 +* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
200 +* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
201 +)))
143 143  
203 +[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
144 144  
145 -= Best Practices and Guide =
146 146  
147 -== Install ==
148 148  
149 -Logbook is required (used again for pick up & metadata creation)
150 150  
151 -- station name
208 +[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
152 152  
153 -- lat / long
210 +----
154 154  
155 -- team members
212 +=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
156 156  
157 -- date and local time
214 +==== **Node Registration and Software Setup** ====
158 158  
159 -- SN of sensor
216 +1. (((
217 +**Registering Nodes in the System**:
160 160  
161 -- notes on site
219 +* To begin, register the nodes in the system so the software can recognize them.
220 +* Navigate to the installation folder of “SmartSoloApps SoloLite”.
221 +* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
222 +* To avoid double registration, replace the file each time you register a new node.
223 +)))
224 +1. (((
225 +**Creating a New Project in SoloLite**:
162 162  
163 -Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
227 +* Open the “SoloLite” software.
228 +* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
229 +* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
230 +)))
164 164  
165 -Take compass measurement away from node and fences [make sure to adjust inclination angle]
232 +==== **Data Downloading Process** ====
166 166  
167 -Take many photos from the site from different angles 
234 +1. (((
235 +**Initiating Data Download**:
168 168  
169 -Add a precise site description to the notes such as distances and orientations from landmarks 
237 +* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
238 +* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
239 +* Select all nodes and right-click to “force download”. This starts the download process.
240 +* Completed downloads will appear as new folders in the Downloaded Data panel.
241 +)))
242 +1. (((
243 +**Exporting Data in Readable Format**:
170 170  
171 -It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
245 +* Go to the “Tool” menu and select “export seismic data”.
246 +* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
247 +* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
248 +* (% class="box warningmessage" %)
249 +(((
250 +* **Ensure to export data as "COUNTS", not "mV".**
172 172  
173 -Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
252 +* **Set "Remove Gain" to the same decibel gain as during programming (ANU usually sets this to 18 db, but double-check).**
253 +)))
254 +)))
174 174  
175 -Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
256 +==== **Handling Nodes During Download** ====
176 176  
177 -Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
258 +1. (((
259 +**Monitoring Download Indicators**:
178 178  
179 -Create metadata .xml file
261 +* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
262 +* Disconnect nodes properly before unplugging anything.
263 +* Be cautious: if the laptop enters sleep mode, the download will pause.
264 +)))
265 +1. (((
266 +//**Investment in Storage Hardware**~://
180 180  
268 +* (% class="box warningmessage" %)
269 +(((
270 +* **Use fast external hard drives to avoid limitations in data harvesting.**
181 181  
182 -== Removing/Demob ==
272 +* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
273 +)))
274 +)))
275 +1. (((
276 +**Metadata and Time Settings**:
183 183  
184 -Download and then use the GPS file to locate the node 
278 +* Ensure all metadata is saved with the file.
279 +* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
280 +)))
281 +1. (((
282 +**Finalizing the Download**:
185 185  
186 -Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
284 +* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
187 187  
286 +
287 +)))
188 188  
189 -Upload photos of the site  
289 +[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
190 190  
191 -- station name
192 192  
193 -- latitude
194 194  
195 -- longitude
293 +[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
196 196  
197 -- elevation
198 198  
199 -* SN of sensor – SN of battery (optional)
200 -* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
201 201  
202 -Upload photos into Google Earth and on a shared drive
203 203  
204 -Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
298 +[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
205 205  
206 -Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
207 207  
208 -Take a photo of the entire setup node with the label on it + compass 
209 209  
210 -Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
302 +[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
211 211  
212 212  
213 -== Charging ==
214 214  
215 -Clean node prior to charging and harvesting the data
306 +[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
216 216  
217 -Remove battery (and spike) from the sensor by twisting the spike part of the instrument
308 +----
218 218  
219 -Set 16 nodes into the charging box (spikes up)
310 +=== **Cleaning** ===
220 220  
221 -Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
312 +**Procedure for Seismic Nodes:**
222 222  
223 -This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
314 +* If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
224 224  
225 -[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
226 -
227 -
228 -
229 -== Downloading and Converting Data to MiniSeed ==
230 -
231 -
232 -The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
233 -
234 -[[image:1705195543887-977.png]]
235 -
236 -
237 -Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
238 -
239 -[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
240 -
241 -
242 -Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
243 -
244 -[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
245 -
246 -At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
247 -
248 -(% class="box warningmessage" %)
249 -(((
250 -**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
316 += =
251 251  )))
252 252  
253 -(% class="box warningmessage" %)
254 -(((
255 -**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
256 -)))
257 -
258 -A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
259 -
260 -Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
261 -
262 -[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
263 -
264 -When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
265 -
266 -(% class="box infomessage" %)
267 -(((
268 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
269 -)))
270 -
271 -When downloading, ensure that all metadata is saved along with the file.
272 -
273 -Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
274 -
275 -//Once downloaded, mark the "D" box on your temporary labels!//
276 -
277 -== Converting data ==
278 -
279 -Check the data all have been converted to miniseed correctly 
280 -
281 -– 3 files per station per day 
282 -
283 -* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
284 -* ~~ 5 Gb / node / month
285 -
286 -//Tick ‘R’ box on the node label//
287 -
288 -
289 -== Cleaning ==
290 -
291 -If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
292 -
293 -
294 -)))
295 -
296 -
297 297  (% class="col-xs-12 col-sm-4" %)
298 298  (((
299 299  (% class="box" %)
1706153266647-145.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +839.4 KB
Content