Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 18.1
edited by Sima Mousavi
on 2024/01/16 15:53
Change comment: There is no comment for this version
To version 55.1
edited by KB
on 2025/05/26 13:10
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SmartSolo Nodes
1 +SmartSolo Seismometers
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.sima
1 +XWiki.Kimberley
Content
... ... @@ -2,221 +2,323 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -= **Node Setup** =
5 += **Node Types** =
6 6  
7 -Short term (~~30 day) battery powered nodes
7 +ANSIR carry two types of three-channel nodes
8 8  
9 -== **Pre-Fieldwork Preparation** ==
9 +* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 +* **SmartSolo BD3C-5 (5 Second Broad-Band)**
10 10  
12 +Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
13 +
14 +
15 +----
16 +
17 += **Programming Defaults** =
18 +
19 +ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
20 +
21 +
22 += **Fieldwork Preparation** =
23 +
11 11  (% class="box infomessage" %)
12 12  (((
13 -**~ INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING **
26 +(% class="box warningmessage" %)
27 +(((
28 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
29 +
30 +**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
14 14  )))
32 +)))
15 15  
16 -== **Installation** ==
34 += **Installation** =
17 17  
18 -* (((
19 -**Logbook Maintenance**: Document essential details:
36 +== **1. Logbook documentation** ==
20 20  
21 -* Station name, latitude/longitude, team members, date/time.
22 -* Serial number (SN) of sensor, site notes.
38 +(((
39 +**Essential Details**: Record the following in a logbook:
40 +
41 +* Station name
42 +* Latitude and longitude
43 +* Names of team members present
44 +* Date and local time of installation
45 +* Serial number (SN) of the sensor
46 +* Detailed notes on the site conditions and setup
47 +
48 +== **2. Node Placement** ==
23 23  )))
24 -* **Node Placement**: Use biodegradable plastic bags for node protection.
25 -* **Orientation and Site Description**:
26 -** Compass measurements (adjust for inclination).
27 -** Detailed description of the site, including landmarks.
28 -* **Visibility and GPS Marking**:
29 -** Use distinctively colored flags for easy location.
30 -** Mark location with GPS; record in logbook and device.
31 -* **Photo Documentation**: Take multiple photos from various angles.
32 32  
33 -= =
51 +**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
34 34  
35 -= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
53 +**Site Analysis**:
36 36  
37 -blahblah
55 +* **Take compass measurements away from the sensor as it will affect your measurement.**
56 +* Take multiple photographs from various angles to document the site setup thoroughly.
57 +* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
38 38  
39 -== Sub-paragraph ==
59 +== **3. GPS Considerations** ==
40 40  
61 +(% class="wikigeneratedid" %)
62 +The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
41 41  
42 -== ==
64 +== **4. Visibility and Location Marking** ==
43 43  
66 +**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
44 44  
45 -= Smart Solo BD3C-5 (5 second) Broad-Band Node =
68 +**GPS Marking**:
46 46  
47 -Lorem
70 +* Use a GPS device to mark the instrument's exact location.
71 +* Record this location in both your paper notes and the GPS device.
48 48  
49 -[[image:1705196270090-364.png]]
73 +== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5. Charge Time, Pre-Deployment & Post-Deployment**(%%) ==
50 50  
75 +* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
76 +* **Pre-Deployment Charging**:
77 +** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
51 51  
52 -== GPS Considerations ==
79 +* **Operational Duration**:
80 +** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
53 53  
54 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
82 +* **Post-Retrieval Charging**:
83 +** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
84 +* **Storage and Shipping Charge Level**:
85 +** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
86 +** This charge level is recommended to prevent battery damage and is safe for transportation.
87 +** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
55 55  
56 -= Keeping the Instruments Clean =
89 +(((
90 +== **6. Data Sharing and Metadata Creation** ==
91 +)))
57 57  
58 -Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
93 +**GPS Data**:
59 59  
95 +* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
60 60  
61 -= Charge Time, Instrument Life, and Charge During Storage & Shipping =
97 +**Photo Sharing**:
62 62  
63 -Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
99 +* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
64 64  
65 -Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
101 +**Metadata File**:
66 66  
103 +* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]].
67 67  
68 -= Best Practices and Guide =
105 +== **7. Additional Best Practices** ==
69 69  
70 -== Install ==
107 +* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
71 71  
72 -Logbook is required (used again for pick up & metadata creation)
109 +----
73 73  
74 -- station name
111 += **Seismic Station Demobilization and Documentation** =
75 75  
76 -- lat / long
113 +1. (((
114 +**Preparation for Demobilization**:
77 77  
78 -- team members
116 +* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
117 +)))
118 +1. (((
119 +**Locating the instrument**:
79 79  
80 -- date and local time
121 +* Use the downloaded GPS file to accurately locate the node for demobilization.
122 +* Import this KMZ file onto your phone for easy reference and location tracking.
123 +* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
124 +)))
125 +1. (((
126 +**Labeling Instruments for Demobilization**:
81 81  
82 -- SN of sensor
128 +* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
129 +* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
130 +* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
131 +)))
132 +1. (((
133 +**Photographing the Setup Node**:
83 83  
84 -- notes on site
135 +* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
136 +* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
137 +)))
138 +1. (((
139 +**Logging Demobilization Details**:
85 85  
86 -Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
141 +* Use the field logbook to note the time of demobilization, serial numbers, and station name.
142 +* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
143 +)))
144 +1. (((
145 +**Final Checks and Equipment Removal**:
87 87  
88 -Take compass measurement away from node and fences [make sure to adjust inclination angle]
147 +* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
148 +* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
89 89  
90 -Take many photos from the site from different angles 
150 +
151 +)))
91 91  
92 -Add a precise site description to the notes such as distances and orientations from landmarks 
153 +[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
93 93  
94 -It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
155 +----
95 95  
96 -Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
157 += **Charging Procedure for Seismic Nodes** =
97 97  
98 -Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
159 +(((
160 +== **1. Preparation for Charging**: ==
99 99  
100 -Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
162 +* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
163 +)))
101 101  
102 -Create metadata .xml file
165 +(((
166 +== **2. Disassembling the Node**: ==
103 103  
168 +* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
169 +)))
104 104  
105 -== Removing/Demob ==
171 +(((
172 +== **3. Setting Nodes in the Charging Box**: ==
106 106  
107 -Download and then use the GPS file to locate the node 
174 +* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
175 +)))
108 108  
109 -Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
177 +(((
178 +== **4. Monitoring the Charging Process**: ==
110 110  
180 +* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
181 +* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
182 +)))
111 111  
112 -Upload photos of the site  
184 +(((
185 +== **5. Updating Charge Status**: ==
113 113  
114 -- station name
187 +* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
188 +* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
189 +)))
115 115  
116 -- latitude
191 +[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
117 117  
118 -- longitude
119 119  
120 -- elevation
121 121  
122 -* SN of sensor – SN of battery (optional)
123 -* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
124 124  
125 -Upload photos into Google Earth and on a shared drive
196 +[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
126 126  
127 -Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
198 +----
128 128  
129 -Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
200 += **Downloading and Converting Seismic Data to MiniSeed Format** =
130 130  
131 -Take a photo of the entire setup node with the label on it + compass 
202 +== **Node Registration and Software Setup** ==
132 132  
133 -Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
204 +1. (((
205 +**Registering Nodes in the System**:
134 134  
207 +* To begin, register the nodes in the system so the software can recognize them.
208 +* Navigate to the installation folder of “SmartSoloApps SoloLite”.
209 +* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
210 +* To avoid double registration, replace the file each time you register a new node.
211 +)))
212 +1. (((
213 +**Creating a New Project in SoloLite**:
135 135  
136 -== Charging ==
215 +* Open the “SoloLite” software.
216 +* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
217 +* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
218 +)))
137 137  
138 -Clean node prior to charging and harvesting the data
220 +== **Data Downloading Process** ==
139 139  
140 -Remove battery (and spike) from the sensor by twisting the spike part of the instrument
222 +1. (((
223 +**Initiating Data Download**:
141 141  
142 -Set 16 nodes into the charging box (spikes up)
225 +* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
226 +* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
227 +* Select all nodes and right-click to “force download”. This starts the download process.
228 +* Completed downloads will appear as new folders in the Downloaded Data panel.
229 +)))
230 +1. (((
231 +**Exporting Data in Readable Format**:
143 143  
144 -Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
233 +* Go to the “Tool” menu and select “export seismic data”.
234 +* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
235 +* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
236 +* (% class="box warningmessage" %)
237 +(((
238 +* **Ensure to export data as "COUNTS", not "mV".**
145 145  
146 -This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
240 +* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db for short period nodes (a factor of 15.848932), and 6db for broadband nodes).**
241 +)))
242 +)))
147 147  
148 -[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
244 +== **Handling Nodes During Download** ==
149 149  
246 +1. (((
247 +**Monitoring Download Indicators**:
150 150  
249 +* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
250 +* Disconnect nodes properly before unplugging anything.
251 +* Be cautious: if the laptop enters sleep mode, the download will pause.
252 +)))
253 +1. (((
254 +//**Investment in Storage Hardware**~://
151 151  
152 -== Downloading and Converting Data to MiniSeed ==
256 +* (% class="box warningmessage" %)
257 +(((
258 +* **Use fast external hard drives to avoid limitations in data harvesting.**
153 153  
260 +* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
261 +)))
262 +)))
263 +1. (((
264 +**Metadata and Time Settings**:
154 154  
155 -The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
266 +* Ensure all metadata is saved with the file.
267 +* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
268 +)))
269 +1. (((
270 +**Finalizing the Download**:
156 156  
157 -[[image:1705195543887-977.png]]
272 +* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
158 158  
274 +
275 +)))
159 159  
160 -Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
277 +[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
161 161  
162 -[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
163 163  
164 164  
165 -Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
281 +[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
166 166  
167 -[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
168 168  
169 -At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
170 170  
171 -(% class="box warningmessage" %)
172 -(((
173 -**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
174 -)))
175 175  
176 -(% class="box warningmessage" %)
177 -(((
178 -**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
179 -)))
286 +[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
180 180  
181 -A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
182 182  
183 -Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
184 184  
185 -[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
290 +[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
186 186  
187 -When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
188 188  
189 -(% class="box infomessage" %)
190 -(((
191 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
192 -)))
193 193  
194 -When downloading, ensure that all metadata is saved along with the file.
294 +[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
195 195  
196 -Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
296 +----
197 197  
198 -//Once downloaded, mark the "D" box on your temporary labels!//
298 += **Cleaning** =
199 199  
200 -== Converting data ==
300 +**Procedure for Seismic Nodes:**
201 201  
202 -Check the data all have been converted to miniseed correctly 
302 +Top half:
203 203  
204 -– 3 files per station per day 
304 +Bottom half: The metal spikes on the bottom half of the nodes can be cleaned using a wire brush, though should still be wiped down for dust afterwards.
205 205  
206 -* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
207 -* ~~ 5 Gb / node / month
208 208  
209 -//Tick ‘R’ box on the node label//
307 += **Weights (for shipping)** =
210 210  
309 +The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
211 211  
212 -== Cleaning ==
311 +1 bag + 6 SP (IGU-16HR) nodes: 18 kg
213 213  
214 -If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
313 +1 SP (IGU-16HR) data harvester: 21.5 kg
215 215  
216 -
217 -)))
315 +1 SP (IGU-16HR) charger: 26.3 kg
218 218  
317 +1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
219 219  
319 +1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
320 +)))
321 +
220 220  (% class="col-xs-12 col-sm-4" %)
221 221  (((
222 222  (% class="box" %)
... ... @@ -223,24 +223,11 @@
223 223  (((
224 224  **Contents**
225 225  
226 -(% class="wikitoc" %)
227 -* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
228 -** [[Sub-paragraph>>path:#HSub-paragraph]]
229 -** [[ >>path:#H]]
230 -* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
231 -** [[GPS Considerations>>path:#HGPSConsiderations]]
232 -* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
233 -* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
234 -* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
235 -** [[Install>>path:#HInstall]]
236 -** [[Removing/Demob>>path:#HRemoving2FDemob]]
237 -** [[Charging>>path:#HCharging]]
238 -** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
239 -** [[Converting data>>path:#HConvertingdata]]
240 -** [[Cleaning>>path:#HCleaning]]
328 +{{toc/}}
329 +
330 +
241 241  )))
242 242  
243 -
244 244  (% class="box" %)
245 245  (((
246 246  = SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
... ... @@ -254,8 +254,12 @@
254 254  |(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
255 255  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
256 256  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
257 -|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
346 +|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
347 +Lithium-ion battery contained in equipment (168.84 Wh)
348 +
349 +UN3481 PI967 S1
258 258  )))
351 +)))
259 259  
260 260  (% class="box" %)
261 261  (((
... ... @@ -268,10 +268,14 @@
268 268  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
269 269  |(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
270 270  |(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
271 -|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.3 kg
364 +|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
272 272  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
273 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
366 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
367 +Lithium-ion battery contained in equipment (96.48 Wh)
368 +
369 +UN3481 PI967 S2
274 274  )))
371 +)))
275 275  
276 276  
277 277  )))
1706153266647-145.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +839.4 KB
Content
example_metadata.txt
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +2.7 KB
Content
... ... @@ -1,0 +1,46 @@
1 +# AKL-HR Node Array (AHNA) code X5
2 +CITE: Name, Name, and Name. (2023). A Node Array [Data set]. International Federation of Digital Seismograph Networks. https://doi.org/10.7914/8jxr-7029
3 +
4 +#SITE START END LAT LONG ELEV SPS RECORDER S/N SENSOR S/N PROPERTY,LOCALITY,COUNTRY COMMENTS
5 +
6 +# INSTALL
7 +AKL01 20-05-2023T00:00 30-06-2023T00:00 -37.0471 175.5245 75 250 SSNODE_C 590001950 SSNODE_5S 590001950 "Te Puru,Hauraki,NZ"
8 +AKL02 20-05-2023T00:00 30-06-2023T00:00 -36.7476 175.5026 70 250 SSNODE_C 590001943 SSNODE_5S 590001943 "Coromandel Town,Hauraki,NZ"
9 +AKL03 20-05-2023T00:00 30-06-2023T00:00 -36.9694 175.5020 98 250 SSNODE_C 590002068 SSNODE_5S 590002068 "Te Mata,Hauraki,NZ"
10 +AKL05 19-05-2023T19:00 22-02-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001957 SSNODE_5S 590001957 "South Head South,Auckland,NZ" "site was disturbed"
11 +AKL06 19-05-2023T19:00 30-06-2023T00:00 -37.2459 175.3426 34 250 SSNODE_C 590001930 SSNODE_5S 590001930 "Back Miranda,Auckland,NZ"
12 +AKB05 02-05-2023T00:37 30-06-2023T00:00 -36.6651 175.4800 63 250 TSAWR TS085A TRILL120 4875 "Colville,Hauraki,NZ"
13 +
14 +# SERVICE 1
15 +AKL05 22-02-2023T00:00 30-06-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001999 SSNODE_.2S 590001999 "South Head South,Auckland,NZ" "swapped node to shortperiod"
16 +
17 +
18 +
19 +
20 +################### ANY LINE BEGINNING WITH # will be commented! Comments are good!
21 +
22 +
23 +# NOTES
24 +# the start/end time is not critical, but good to have. what IS critical are the times of instrument changes as this potentially affects response information
25 +# to mark equipment changes, add a new line with an updated start date (e.g. AKL05 above)
26 +# can use tabs or spaces, but spaces tend to look nicer. formatting ultimately doesn't matter too much so long as there is any sort of "white space" between the fields
27 +# if you don't know a serial number, put 999. if you don't know the elevation, put 0
28 +# for Nodes, put the same serial number for both Recoder and Sensor (since they are the same!)
29 +
30 +
31 +# EXAMPLE INSTRUMENT LABELS
32 +#LPR200 = ANU LPR-200 logger (beige box)
33 +#TSAWR = ANU TerraSAWR logger (yellow box)
34 +
35 +#TRILL120 = Trillium Compact 120s
36 +#TRILL20 = Trillium Compact 20s
37 +#TRILL120PH = Trillium Compact 120s PostHole
38 +#CMG6TD = Guralp 6TD
39 +#CMG3ESP = Guralp 3ESP
40 +#3DLITE = Lenarrtz 3D-LITE
41 +
42 +#SSNODE_C = output was in COUNTS (there is also SSNODE_MV, if you (accidentally!) output to millivolts etc)
43 +#SSNODE_5S = broadband (can also use SSNODE_BB)
44 +#SSNODE_.2S = shortperiod (can also use SSNODE_SP)
45 +
46 +#it doesn't matter too much what you use for equipment labels, so long as they are consistent and otherwise defined somewhere in the comments!