Skip to Content
Last modified by robert on 2025/08/21 13:08
From version 17.1
edited by Sima Mousavi
on 2024/01/16 15:53
Change comment: There is no comment for this version
To version 74.2
edited by robert
on 2025/07/31 19:59
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SmartSolo Nodes
1 +SmartSolo Node Seismometers
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.sima
1 +XWiki.robert
Content
... ... @@ -2,221 +2,349 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -= **Node Setup** =
5 += **Node Types** =
6 6  
7 -Short term (~~30 day) battery powered nodes
7 +ANSIR carry two types of three-channel nodes
8 8  
9 -== **Pre-Fieldwork Preparation** ==
9 +* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
10 +* **SmartSolo BD3C-5 (5 Second Broadband)**
10 10  
11 ->(% class="box infomessage" %)
12 -(((
13 -**~ INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING **
14 -)))
12 +Both have a battery capacity of around 30 days. The programming, operation and downloading procedures for both types of SmartSolo nodes are also similar.
15 15  
16 -== **Installation** ==
14 +----
17 17  
18 -* (((
19 -**Logbook Maintenance**: Document essential details:
16 += **Programming Defaults** =
20 20  
21 -* Station name, latitude/longitude, team members, date/time.
22 -* Serial number (SN) of sensor, site notes.
23 -)))
24 -* **Node Placement**: Use biodegradable plastic bags for node protection.
25 -* **Orientation and Site Description**:
26 -** Compass measurements (adjust for inclination).
27 -** Detailed description of the site, including landmarks.
28 -* **Visibility and GPS Marking**:
29 -** Use distinctively colored flags for easy location.
30 -** Mark location with GPS; record in logbook and device.
31 -* **Photo Documentation**: Take multiple photos from various angles.
18 +The nodes must be programmed in the SoloLite software prior to use. Screenshots for the short period 16HR-3C and broadband BDC3-5 are shown with our recommended parameters.
32 32  
33 -= =
20 +[[IGU-16 3C (short period node) programming screen set at 250 Hz. Ensure that the highlighted areas are set!>>image:SP_programming.labels.png||alt="IGU-16 3C programming screen"]]
34 34  
35 -= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
22 +[[BD3C-5 (broadband node) programming screen set at 250 hz. Ensure that the highlighted areas are set!>>image:BB_programming.labels.png||alt="BD3C-5 programming screen"]]
36 36  
37 -blahblah
24 +FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
38 38  
39 -== Sub-paragraph ==
26 +Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
40 40  
28 +In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
41 41  
42 -== ==
30 +Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can output to miniseed later.
43 43  
32 +GPS mode is best in cycle mode (e.g. once per hour) instead of constant. The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
44 44  
45 -= Smart Solo BD3C-5 (5 second) Broad-Band Node =
34 +We recommend that the SP 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
46 46  
47 -Lorem
36 +**Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
48 48  
49 -[[image:1705196270090-364.png]]
38 += **Fieldwork Preparation** =
50 50  
40 +(% class="box warningmessage" %)
41 +(((
42 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
51 51  
52 -== GPS Considerations ==
44 +**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
53 53  
54 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
46 +**We have had good experience with the 4Tb Samsung T7 Shield drives.**
47 +)))
55 55  
56 -= Keeping the Instruments Clean =
49 +== Magnets ==
57 57  
58 -Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
51 +If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).
59 59  
53 +== Animal-Proofing ==
60 60  
61 -= Charge Time, Instrument Life, and Charge During Storage & Shipping =
55 +We have experienced times where foxes (or some other animal) will dig up nodes and potentially carry them off for tens or hundreds of meteres. Being sanitary with the rope handles (e.g. not getting food grease on them) seems to help, as well as spraying the nodes and handles with methylated spirits et al. when deploying. There are other specialized products available depending on your environment.
62 62  
63 -Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
57 += **Installation** =
64 64  
65 -Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
59 +(% class="box infomessage" %)
60 +(((
61 +**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
62 +)))
66 66  
64 +== 1. Logbook documentation ==
67 67  
68 -= Best Practices and Guide =
66 +(((
67 +**Essential Details** for field logs:
69 69  
70 -== Install ==
69 +* Station name
70 +* Latitude, longitude, elevation
71 +* Names of team members present
72 +* Date and both local & UTC time of installation/removal
73 +* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
74 +* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
71 71  
72 -Logbook is required (used again for pick up & metadata creation)
76 +[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
73 73  
74 -- station name
78 +== 2. Node Placement ==
79 +)))
75 75  
76 -- lat / long
81 +**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
77 77  
78 -- team members
83 +**Site Analysis**:
79 79  
80 -- date and local time
85 +* **Take compass measurements away from the sensor as it will affect your measurement.**
86 +* Take photographs from various angles to document the site setup thoroughly.
87 +* Include a detailed site description in your notes
81 81  
82 -- SN of sensor
89 +== 3. GPS Considerations ==
83 83  
84 -- notes on site
91 +(% class="wikigeneratedid" %)
92 +The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
85 85  
86 -Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
94 +== 4. Visibility and Location Marking ==
87 87  
88 -Take compass measurement away from node and fences [make sure to adjust inclination angle]
96 +**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
89 89  
90 -Take many photos from the site from different angles 
98 +**GPS Marking**:
91 91  
92 -Add a precise site description to the notes such as distances and orientations from landmarks 
100 +* Use a GPS device to mark the instrument's exact location.
101 +* Record this location in both your paper notes and the GPS device.
93 93  
94 -It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
103 +== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)5. Charge Time, Pre-Deployment & Post-Deployment(%%) ==
95 95  
96 -Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
105 +* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
106 +* **Pre-Deployment Charging**:
107 +** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
97 97  
98 -Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
109 +* **Operational Duration**:
110 +** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
99 99  
100 -Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
112 +* **Post-Retrieval Charging**:
113 +** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
114 +* **Storage and Shipping Charge Level**:
115 +** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
116 +** This charge level is recommended to prevent battery damage and is safe for transportation.
117 +** Nodes should not be stored fully charged, and **they should especially not be stored with 0 charge as this damages lithium batteries.**
101 101  
102 -Create metadata .xml file
119 +(((
120 +== 6. Data Sharing and Metadata Creation ==
121 +)))
103 103  
123 +**GPS Data**:
104 104  
105 -== Removing/Demob ==
125 +* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
106 106  
107 -Download and then use the GPS file to locate the node 
127 +**Photo Sharing**:
108 108  
109 -Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
129 +* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
110 110  
131 +**Metadata File**:
111 111  
112 -Upload photos of the site  
133 +* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.
113 113  
114 -- station name
135 +== 7. Additional Best Practices ==
115 115  
116 -- latitude
137 +* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
117 117  
118 -- longitude
139 +----
119 119  
120 -- elevation
141 += **Seismic Station Demobilization and Documentation** =
121 121  
122 -* SN of sensor – SN of battery (optional)
123 -* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
143 +1. (((
144 +**Preparation for Demobilization**:
124 124  
125 -Upload photos into Google Earth and on a shared drive
146 +* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
147 +)))
148 +1. (((
149 +**Locating the instrument**:
126 126  
127 -Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
151 +* Use the downloaded GPS file to accurately locate the node for demobilization.
152 +* Import this KMZ file onto your phone for easy reference and location tracking.
153 +* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
154 +)))
155 +1. (((
156 +**Labeling Instruments for Demobilization**:
128 128  
129 -Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
158 +* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
159 +* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
160 +* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
161 +)))
162 +1. (((
163 +**Photographing the Setup Node**:
130 130  
131 -Take a photo of the entire setup node with the label on it + compass 
165 +* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
166 +* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
167 +)))
168 +1. (((
169 +**Logging Demobilization Details**:
132 132  
133 -Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
171 +* Use the field logbook to note the time of demobilization, serial numbers, and station name.
172 +* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
173 +)))
174 +1. (((
175 +**Final Checks and Equipment Removal**:
134 134  
177 +* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
178 +* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
135 135  
136 -== Charging ==
180 +
181 +)))
137 137  
138 -Clean node prior to charging and harvesting the data
183 +[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
139 139  
140 -Remove battery (and spike) from the sensor by twisting the spike part of the instrument
185 +----
141 141  
142 -Set 16 nodes into the charging box (spikes up)
187 += **Charging Procedure for Seismic Nodes** =
143 143  
144 -Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
189 +(((
190 +== 1. Preparation for Charging: ==
145 145  
146 -This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
192 +* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
193 +)))
147 147  
148 -[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
195 +(((
196 +== 2. Disassembling the Node: ==
149 149  
198 +* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
199 +)))
150 150  
201 +(((
202 +== 3. Setting Nodes in the Charging Box: ==
151 151  
152 -== Downloading and Converting Data to MiniSeed ==
204 +* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
205 +)))
153 153  
207 +(((
208 +== 4. Monitoring the Charging Process: ==
154 154  
155 -The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
210 +* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
211 +* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
212 +)))
156 156  
157 -[[image:1705195543887-977.png]]
214 +(((
215 +== 5. Updating Charge Status: ==
158 158  
217 +* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
218 +* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
219 +)))
159 159  
160 -Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
221 +[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
161 161  
162 -[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
163 163  
164 164  
165 -Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
166 166  
167 -[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
226 +[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
168 168  
169 -At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
228 +----
170 170  
171 -(% class="box warningmessage" %)
172 -(((
173 -**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
230 += **Downloading and Converting Seismic Data to MiniSeed Format** =
231 +
232 +== Node Registration and Software Setup ==
233 +
234 +1. (((
235 +**Registering Nodes in the System**:
236 +
237 +* To begin, register the nodes in the system so the software can recognize them.
238 +* Navigate to the installation folder of “SmartSoloApps SoloLite”.
239 +* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
240 +* To avoid double registration, replace the file each time you register a new node.
174 174  )))
242 +1. (((
243 +**Creating a New Project in SoloLite**:
175 175  
176 -(% class="box warningmessage" %)
177 -(((
178 -**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
245 +* Open the “SoloLite” software.
246 +* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
247 +* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
179 179  )))
180 180  
181 -A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
250 +== Data Downloading Process ==
182 182  
183 -Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
252 +1. (((
253 +**Initiating Data Download**:
184 184  
185 -[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
255 +* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
256 +* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
257 +* Select all nodes and right-click to “force download”. This starts the download process.
258 +* Completed downloads will appear as new folders in the Downloaded Data panel.
259 +)))
260 +1. (((
261 +**Exporting Data in Readable Format**:
186 186  
187 -When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
263 +* Go to the “Tool” menu and select “export seismic data”.
264 +* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
265 +* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
266 +* (% class="box warningmessage" %)
267 +(((
268 +* **Ensure to export data as "COUNTS" (int32), not "mV" (float). This is critical!**
188 188  
189 -(% class="box infomessage" %)
270 +* **Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.**
271 +)))
272 +)))
273 +
274 +== Handling Nodes During Download ==
275 +
276 +1. (((
277 +**Monitoring Download Indicators**:
278 +
279 +* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
280 +* Disconnect nodes properly before unplugging anything.
281 +* Be cautious: if the laptop enters sleep mode, the download will pause.
282 +)))
283 +1. (((
284 +//**Investment in Storage Hardware**~://
285 +
286 +* (% class="box warningmessage" %)
190 190  (((
191 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
288 +* **Use fast external hard drives to avoid limitations in data harvesting.**
289 +
290 +* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
291 +* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
192 192  )))
293 +)))
294 +1. (((
295 +**Metadata and Time Settings**:
193 193  
194 -When downloading, ensure that all metadata is saved along with the file.
297 +* Ensure all metadata is saved with the file.
298 +* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
299 +)))
300 +1. (((
301 +**Finalizing the Download**:
195 195  
196 -Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
303 +* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
197 197  
198 -//Once downloaded, mark the "D" box on your temporary labels!//
305 +
306 +)))
199 199  
200 -== Converting data ==
308 +[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
201 201  
202 -Check the data all have been converted to miniseed correctly 
203 203  
204 -– 3 files per station per day 
205 205  
206 -* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
207 -* ~~ 5 Gb / node / month
312 +[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
208 208  
209 -//Tick ‘R’ box on the node label//
210 210  
211 211  
212 -== Cleaning ==
213 213  
214 -If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
317 +[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
215 215  
216 -
217 -)))
218 218  
219 219  
321 +[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
322 +
323 +
324 +
325 +[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
326 +
327 +----
328 +
329 += **Cleaning** =
330 +
331 +When still connected, the nodes are water resistant (don't submerge them!) and can handle a good spray / wipedown. A strong, non-wire brush is helpful to reach areas between the metal spikes on the bottom.
332 +
333 += **Weights (for shipping)** =
334 +
335 +The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
336 +
337 +1 bag + 6 SP (IGU-16HR) nodes: 18 kg
338 +
339 +1 SP (IGU-16HR) data harvester: 21.5 kg
340 +
341 +1 SP (IGU-16HR) charger: 26.3 kg
342 +
343 +1 BB (BD3C-5) charger/data harvester (with and without 16 cables): 21 kg / 14.5 kg
344 +
345 +1 case + 5 BB (BD3C-5) nodes and 6 BB nodes: 22 kg / 25 kg
346 +)))
347 +
220 220  (% class="col-xs-12 col-sm-4" %)
221 221  (((
222 222  (% class="box" %)
... ... @@ -223,24 +223,11 @@
223 223  (((
224 224  **Contents**
225 225  
226 -(% class="wikitoc" %)
227 -* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
228 -** [[Sub-paragraph>>path:#HSub-paragraph]]
229 -** [[ >>path:#H]]
230 -* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
231 -** [[GPS Considerations>>path:#HGPSConsiderations]]
232 -* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
233 -* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
234 -* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
235 -** [[Install>>path:#HInstall]]
236 -** [[Removing/Demob>>path:#HRemoving2FDemob]]
237 -** [[Charging>>path:#HCharging]]
238 -** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
239 -** [[Converting data>>path:#HConvertingdata]]
240 -** [[Cleaning>>path:#HCleaning]]
354 +{{toc/}}
355 +
356 +
241 241  )))
242 242  
243 -
244 244  (% class="box" %)
245 245  (((
246 246  = SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
... ... @@ -254,12 +254,16 @@
254 254  |(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
255 255  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
256 256  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
257 -|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
372 +|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
373 +Lithium-ion battery contained in equipment (168.84 Wh)
374 +
375 +UN3481 PI967 S1
258 258  )))
377 +)))
259 259  
260 260  (% class="box" %)
261 261  (((
262 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
381 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
263 263  
264 264  [[image:smartsolo node.jpg]]
265 265  
... ... @@ -268,11 +268,87 @@
268 268  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
269 269  |(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
270 270  |(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
271 -|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.3 kg
390 +|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
272 272  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
273 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
392 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
393 +Lithium-ion battery contained in equipment (96.48 Wh)
394 +
395 +UN3481 PI967 S2
274 274  )))
397 +)))
275 275  
276 -
399 +(% class="box" %)
400 +(((
401 += SmartSolo BD3C-16 Portable Battery Charger =
402 +
403 +[[image:20250729_125049.jpg]]
404 +
405 +|**Dimensions (LxHxW)**|558 x 357 x 300mm
406 +|**Input rating**|100-210V - 50/60Hz
407 +|**Power**|1000W
408 +|**Weight**|14.5kg
409 +|**Weight with cables**|21kg
277 277  )))
411 +
412 +(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
413 +(((
414 += SmartSolo IGU-16 Portable Data Harvester =
415 +
416 +[[image:20250729_124747.jpg]]
417 +
418 +|**Dimensions (LxHxW)**|625 x 500 x 366mm
419 +|**Input rating**|100-210V - 50/60Hz
420 +|**Power**|100W
421 +|**Weight**|21.5 - 24kg
422 +|**Slots no.**|16
423 +|**Download Speed**|20MB/sec/slot
278 278  )))
425 +
426 +(% class="box" %)
427 +(((
428 += SmartSolo IGU-16 Portable Battery Charger =
429 +
430 += [[image:20250729_124644.jpg]] =
431 +
432 +|**Dimensions (LxHxW)**|625 x 500 x 366mm
433 +|**Input rating**|100-210V - 50/60Hz
434 +|**Power**|640W
435 +|**Weight**|26.3kg
436 +|**Slots no.**|16
437 +)))
438 +
439 +(% class="box" %)
440 +(((
441 += SmartSolo BD3C-5 Carry Bag =
442 +
443 +[[image:20250729_124957.jpg]]
444 +
445 +
446 +|**Dimensions (LxHxW)**|590 x 225 x 405mm
447 +|**Weight**|8.2kg
448 +|**Slots no.**|6
449 +)))
450 +
451 +(% class="box" %)
452 +(((
453 += SmartSolo IGU-16 3C Carry Bag =
454 +
455 +[[image:20250729_124502.jpg]]
456 +
457 +|**Dimensions (LxHxW)**|230 x 340 x 310mm
458 +|**Weight**|3.6kg
459 +|**Slots no.**|6
460 +)))
461 +
462 +(% class="box" %)
463 +(((
464 += SmartSolo IGU-16 1C Carry Bag =
465 +
466 +[[image:20250729_124558.jpg]]
467 +
468 +|**Dimensions (LxHxW)**|225 x 200 x 550mm
469 +|**Weight**|
470 +|**Slots no.**|6
471 +)))
472 +)))
473 +)))
1706153266647-145.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.sima
Size
... ... @@ -1,0 +1,1 @@
1 +839.4 KB
Content
20250729_124502.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.JackD
Size
... ... @@ -1,0 +1,1 @@
1 +457.6 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +111.5 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +106.7 KB
Content
example_metadata.txt
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.robert
Size
... ... @@ -1,0 +1,1 @@
1 +2.7 KB
Content
... ... @@ -1,0 +1,46 @@
1 +# AKL-HR Node Array (AHNA) code X5
2 +CITE: Name, Name, and Name. (2023). A Node Array [Data set]. International Federation of Digital Seismograph Networks. https://doi.org/10.7914/8jxr-7029
3 +
4 +#SITE START END LAT LONG ELEV SPS RECORDER S/N SENSOR S/N PROPERTY,LOCALITY,COUNTRY COMMENTS
5 +
6 +# INSTALL
7 +AKL01 20-05-2023T00:00 30-06-2023T00:00 -37.0471 175.5245 75 250 SSNODE_C 590001950 SSNODE_5S 590001950 "Te Puru,Hauraki,NZ"
8 +AKL02 20-05-2023T00:00 30-06-2023T00:00 -36.7476 175.5026 70 250 SSNODE_C 590001943 SSNODE_5S 590001943 "Coromandel Town,Hauraki,NZ"
9 +AKL03 20-05-2023T00:00 30-06-2023T00:00 -36.9694 175.5020 98 250 SSNODE_C 590002068 SSNODE_5S 590002068 "Te Mata,Hauraki,NZ"
10 +AKL05 19-05-2023T19:00 22-02-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001957 SSNODE_5S 590001957 "South Head South,Auckland,NZ" "site was disturbed"
11 +AKL06 19-05-2023T19:00 30-06-2023T00:00 -37.2459 175.3426 34 250 SSNODE_C 590001930 SSNODE_5S 590001930 "Back Miranda,Auckland,NZ"
12 +AKB05 02-05-2023T00:37 30-06-2023T00:00 -36.6651 175.4800 63 250 TSAWR TS085A TRILL120 4875 "Colville,Hauraki,NZ"
13 +
14 +# SERVICE 1
15 +AKL05 22-02-2023T00:00 30-06-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001999 SSNODE_.2S 590001999 "South Head South,Auckland,NZ" "swapped node to shortperiod"
16 +
17 +
18 +
19 +
20 +################### ANY LINE BEGINNING WITH # will be commented! Comments are good!
21 +
22 +
23 +# NOTES
24 +# the start/end time is not critical, but good to have. what IS critical are the times of instrument changes as this potentially affects response information
25 +# to mark equipment changes, add a new line with an updated start date (e.g. AKL05 above)
26 +# can use tabs or spaces, but spaces tend to look nicer. formatting ultimately doesn't matter too much so long as there is any sort of "white space" between the fields
27 +# if you don't know a serial number, put 999. if you don't know the elevation, put 0
28 +# for Nodes, put the same serial number for both Recoder and Sensor (since they are the same!)
29 +
30 +
31 +# EXAMPLE INSTRUMENT LABELS
32 +#LPR200 = ANU LPR-200 logger (beige box)
33 +#TSAWR = ANU TerraSAWR logger (yellow box)
34 +
35 +#TRILL120 = Trillium Compact 120s
36 +#TRILL20 = Trillium Compact 20s
37 +#TRILL120PH = Trillium Compact 120s PostHole
38 +#CMG6TD = Guralp 6TD
39 +#CMG3ESP = Guralp 3ESP
40 +#3DLITE = Lenarrtz 3D-LITE
41 +
42 +#SSNODE_C = output was in COUNTS (there is also SSNODE_MV, if you (accidentally!) output to millivolts etc)
43 +#SSNODE_5S = broadband (can also use SSNODE_BB)
44 +#SSNODE_.2S = shortperiod (can also use SSNODE_SP)
45 +
46 +#it doesn't matter too much what you use for equipment labels, so long as they are consistent and otherwise defined somewhere in the comments!
XWiki.XWikiRights[0]
Allow/Deny
... ... @@ -1,0 +1,1 @@
1 +Allow
Groups
... ... @@ -1,0 +1,1 @@
1 +XWiki.XWikiAllGroup
Levels
... ... @@ -1,0 +1,1 @@
1 +comment
XWiki.XWikiRights[1]
Allow/Deny
... ... @@ -1,0 +1,1 @@
1 +Allow
Levels
... ... @@ -1,0 +1,1 @@
1 +comment
Users
... ... @@ -1,0 +1,1 @@
1 +XWiki.XWikiGuest