Changes for page SmartSolo Node Seismometers

Last modified by robert on 2025/08/21 13:08

From 16.1 to 17.1 From 44.2 to 45.1

From version 17.1

edited by Sima Mousavi
on 2024/01/16 15:53

Change comment: There is no comment for this version

To version 44.2

edited by robert
on 2024/05/14 18:39

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 3 added, 0 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.sima
++XWiki.robert

Content

@@ -2,221 +2,310 @@
  (((
  (% class="col-xs-12 col-sm-8" %)
  (((
--= **Node Setup** =
++= **Node Types** =
--Short term (~~30 day) battery powered nodes
++ANSIR carry two types of three-channel nodes
--== **Pre-Fieldwork Preparation** ==
++* **SmartSolo IGU 16HR 3C (5 Hz Short Period)**
++* **SmartSolo BD3C-5 (5 Second Broad-Band)**
-->(% class="box infomessage" %)
--(((
--**~ INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING **
--)))
++Both have a battery capacity of around 30 days. The programming, operation, and downloading procedures for both types of SmartSolo nodes are also similar.
--== **Installation** ==
--* (((
--**Logbook Maintenance**: Document essential details:
++----
--* Station name, latitude/longitude, team members, date/time.
--* Serial number (SN) of sensor, site notes.
--)))
--* **Node Placement**: Use biodegradable plastic bags for node protection.
--* **Orientation and Site Description**:
--** Compass measurements (adjust for inclination).
--** Detailed description of the site, including landmarks.
--* **Visibility and GPS Marking**:
--** Use distinctively colored flags for easy location.
--** Mark location with GPS; record in logbook and device.
--* **Photo Documentation**: Take multiple photos from various angles.
++= **Programming Defaults** =
--=   =
++ANU recommends that the SP 16HR-3C be set to a gain of 24db and no higher than 250 Hz sampling rate. The BD3C-5 should be set to a gain of 6db (maximum allowed). These are what we use for our internal experiments. **Note that this gain must be removed when exporting to miniseed, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high. We also recommend disabling bluetooth to increase battery life, and to enable "FIFO" mode just in case old data is still present on the units and you run out of space (although it is unlikely you will go over 64 Gb for one deploy). If using the "timed turn-on" option, please be aware that **the units will not begin recording until they have acquired a GPS lock**, which may nor occur if they are buried too deeply or have very poor sky view.
--= SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
--blahblah
++= **Fieldwork Preparation** =
--== Sub-paragraph ==
++(% class="box infomessage" %)
++(((
++(% class="box warningmessage" %)
++(((
++**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
++**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
++)))
++)))
--==   ==
++= **Installation** =
++=== **1- Logbook documentation** ===
--= Smart Solo BD3C-5 (5 second) Broad-Band Node =
++(((
++**Essential Details**: Record the following in a logbook:
--Lorem
++* Station name
++* Latitude and longitude
++* Names of team members present
++* Date and local time of installation
++* Serial number (SN) of the sensor
++* Detailed notes on the site conditions and setup
--[[image:1705196270090-364.png]]
++=== **2- Node Placement** ===
++)))
++**Protection**: Place nodes inside (landfill) biodegradable bags to minimize cleaning and cross-site soil contamination.
--== GPS Considerations ==
++**Site Analysis**:
--The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
++* **Take compass measurements away from the sensor as it will affect your measurement.**
++* Take multiple photographs from various angles to document the site setup thoroughly.
++* Include a detailed site description in your notes, specifying distances and orientations from nearby landmarks (e.g. Richards garden, Te Mini steam field eastern side)
--= Keeping the Instruments Clean =
++=== **3- GPS Considerations** ===
--Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
++(% class="wikigeneratedid" %)
++The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
++=== **4- Visibility and Location Marking** ===
--= Charge Time, Instrument Life, and Charge During Storage & Shipping =
++**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
--Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
++**GPS Marking**:
--Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
++* Use a GPS device to mark the instrument's exact location.
++* Record this location in both your paper notes and the GPS device.
++=== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)**5- Charge Time, Pre-Deployment & Post-Deployment**(%%) ===
--= Best Practices and Guide =
++* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
++* **Pre-Deployment Charging**:
++** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
--== Install ==
++* **Operational Duration**:
++** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
--Logbook is required (used again for pick up & metadata creation)
++* **Post-Retrieval Charging**:
++** After retrieval, charge the instruments to about 50-60% (indicated as "orange" level) unless they are to be immediately re-deployed.
++* **Storage and Shipping Charge Level**:
++** Maintain a battery charge level of around 50-60% (e.g. "orange") for both storage and shipping purposes.
++** This charge level is recommended to prevent battery damage and is safe for transportation.
++** Nodes should not be stored fully charged, and it **they should especially not be stored with 0 charge.**
--- station name
++(((
++=== **6- Data Sharing and Metadata Creation** ===
++)))
--- lat / long
++**GPS Data**:
--- team members
++* Ensure you have documented precise lat/lon locations for each station and **DOCUMENTED THIS CAREFULLY**
--- date and local time
++**Photo Sharing**:
--- SN of sensor
++* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
--- notes on site
++**Metadata File**:
--Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
++* Create and organize metadata via the ANU metadata standard (~*~*add example)
--Take compass measurement away from node and fences [make sure to adjust inclination angle]
++=== **7- Additional Best Practices** ===
--Take many photos from the site from different angles
++* **Environmental Responsibility**: Ensure that the node placement and the materials used are environmentally responsible and adhere to local regulations.
++* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
--Add a precise site description to the notes such as distances and orientations from landmarks
++* (((
++==== **Keeping the Instruments Clean** ====
++)))
++* (((
++Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
++)))
--It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
++----
--Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
++= **Seismic Station Demobilization and Documentation** =
--Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
++1. (((
++**Preparation for Demobilization**:
--Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
++* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
++)))
++1. (((
++**Locating the instrument**:
--Create metadata .xml file
++* Use the downloaded GPS file to accurately locate the node for demobilization.
++* Import this KMZ file onto your phone for easy reference and location tracking.
++* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
++)))
++1. (((
++**Labeling Instruments for Demobilization**:
++* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
++* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
++* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
++)))
++1. (((
++**Photographing the Setup Node**:
--== Removing/Demob ==
++* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
++* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
++)))
++1. (((
++**Logging Demobilization Details**:
--Download and then use the GPS file to locate the node
++* Use the field logbook to note the time of demobilization, serial numbers, and station name.
++* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
++)))
++1. (((
++**Final Checks and Equipment Removal**:
--Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.
++* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
++* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
++
++)))
--Upload photos of the site
++[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
--- station name
++----
--- latitude
++= **Charging Procedure for Seismic Nodes** =
--- longitude
++1. (((
++=== **Preparation for Charging**: ===
--- elevation
++* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
++)))
++1. (((
++=== **Disassembling the Node**: ===
--* SN of sensor – SN of battery (optional)
--* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side)
++* For the IGU-16HR, remove the battery (bottom half) from the sensor. This is done by unscrewing the spikes counter-clockwise.
++)))
++1. (((
++=== **Setting Nodes in the Charging Box**: ===
--Upload photos into Google Earth and on a shared drive
++* Place 1-16 IGU-16HR battery components upside-down into the charger, assuring they are oriented properly.
++)))
++1. (((
++=== **Monitoring the Charging Process**: ===
--Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!).
++* Once the nodes are set in the charging box and the charging process begins, lights adjacent to the batteries will illuminate. These lights indicate that charging is underway.
++* Observe the transition of the lights from steady red to orange, then to green, and finally to flashing green. A flashing green light signifies that the batteries are fully charged. For storage, the goal is to charge them to ORANGE.
++)))
++1. (((
++=== **Updating Charge Status**: ===
--Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
++* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
++* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
++)))
--Take a photo of the entire setup node with the label on it + compass
++[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
--Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
--== Charging ==
--Clean node prior to charging and harvesting the data
++[[image:1706153354750-415.png||data-xwiki-image-style-alignment="center" height="317" width="562"]]
--Remove battery (and spike) from the sensor by twisting the spike part of the instrument
++----
--Set 16 nodes into the charging box (spikes up)
++=== **Downloading and Converting Seismic Data to MiniSeed Format** ===
--Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
++==== **Node Registration and Software Setup** ====
--This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
++1. (((
++**Registering Nodes in the System**:
--[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
++* To begin, register the nodes in the system so the software can recognize them.
++* Navigate to the installation folder of “SmartSoloApps SoloLite”.
++* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
++* To avoid double registration, replace the file each time you register a new node.
++)))
++1. (((
++**Creating a New Project in SoloLite**:
++* Open the “SoloLite” software.
++* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
++* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
++)))
++==== **Data Downloading Process** ====
--== Downloading and Converting Data to MiniSeed ==
++1. (((
++**Initiating Data Download**:
++* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
++* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
++* Select all nodes and right-click to “force download”. This starts the download process.
++* Completed downloads will appear as new folders in the Downloaded Data panel.
++)))
++1. (((
++**Exporting Data in Readable Format**:
--The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
++* Go to the “Tool” menu and select “export seismic data”.
++* Tailor other parameters to personal preference and ensure "Sample Interval" matches the setting used during node reset.
++* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
++* (% class="box warningmessage" %)
++(((
++* **Ensure to export data as "COUNTS", not "mV".**
--[[image:1705195543887-977.png]]
++* **Set "Remove Gain" to the same decibel gain as during programming** **(by default ANU sets this to 24db (a factor of 15.848932).**
++)))
++)))
++==== **Handling Nodes During Download** ====
--Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
++1. (((
++**Monitoring Download Indicators**:
--[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
++* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
++* Disconnect nodes properly before unplugging anything.
++* Be cautious: if the laptop enters sleep mode, the download will pause.
++)))
++1. (((
++//**Investment in Storage Hardware**~://
++* (% class="box warningmessage" %)
++(((
++* **Use fast external hard drives to avoid limitations in data harvesting.**
--Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
++* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
++)))
++)))
++1. (((
++**Metadata and Time Settings**:
--[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
++* Ensure all metadata is saved with the file.
++* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
++)))
++1. (((
++**Finalizing the Download**:
--At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
++* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
--(% class="box warningmessage" %)
--(((
--**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
++
  )))
--(% class="box warningmessage" %)
--(((
--**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
--)))
++[[image:1706153266647-145.png||data-xwiki-image-style-alignment="center" height="340" width="603"]]
--A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
--Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
--[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
++[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
--When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
--(% class="box infomessage" %)
--(((
--**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
--)))
--When downloading, ensure that all metadata is saved along with the file.
--Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
++[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
--//Once downloaded, mark the "D" box on your temporary labels!//
--== Converting data ==
--Check the data all have been converted to miniseed correctly
++[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
--– 3 files per station per day
--* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
--* ~~ 5 Gb / node / month
--//Tick ‘R’ box on the node label//
++[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
++----
--== Cleaning ==
++=== **Cleaning** ===
--If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
++**Procedure for Seismic Nodes:**
--
++* If the nodes are placed in a sturdy plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
  )))
--
  (% class="col-xs-12 col-sm-4" %)
  (((
  (% class="box" %)
@@ -223,24 +223,11 @@
  (((
  **Contents**
--(% class="wikitoc" %)
--* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
--** [[Sub-paragraph>>path:#HSub-paragraph]]
--** [[ >>path:#H]]
--* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
--** [[GPS Considerations>>path:#HGPSConsiderations]]
--* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
--* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
--* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
--** [[Install>>path:#HInstall]]
--** [[Removing/Demob>>path:#HRemoving2FDemob]]
--** [[Charging>>path:#HCharging]]
--** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
--** [[Converting data>>path:#HConvertingdata]]
--** [[Cleaning>>path:#HCleaning]]
++{{toc/}}
++
++
  )))
--
  (% class="box" %)
  (((
  = SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
@@ -268,9 +268,9 @@
  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
  |(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
  |(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
--|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.3 kg
++|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
--|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
++|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Lithium ion XXAh
  )))

1706153266647-145.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+1.7 MB

Content

1706153354750-415.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+2.1 MB

Content

1706153556166-231.jpeg

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.sima

Size

...	...	@@ -1,0 +1,1 @@
	1	+839.4 KB

Content

Changes for page SmartSolo Node Seismometers

Summary

Details

Applications

Navigation