Skip to Content
Last modified by robert on 2026/09/07 17:05
From version 119.2
edited by robert
on 2026/09/07 15:45
Change comment: There is no comment for this version
To version 17.1
edited by Dr Sima Mousavi
on 2024/01/16 15:53
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -SmartSolo Node Seismometers
1 +SmartSolo Nodes
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.robert
1 +XWiki.sima
Content
... ... @@ -2,528 +2,221 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -= **Node Types** =
5 += **Node Setup** =
6 6  
7 -ANSIR supply two types of three-channel nodes, and one type of one-channel node:
7 +Short term (~~30 day) battery powered nodes
8 8  
9 -* **SmartSolo IGU-16HR 3C (5 Hz, 'very' short period)**
10 -* **SmartSolo BD3C-5 (5 second, short period)**
11 -* **SmartSolo IGU-16 1C (5 Hz, 'very' short period, single channel. Not 'HR')**
9 +== **Pre-Fieldwork Preparation** ==
12 12  
13 -Visit the [[SmartSolo page>>https://smartsolo.com/igu.html]] for more detail.
14 -
15 -The three-channel nodes have a theoretical battery capacity of ~~30 days, whereas the single-channel type has a capacity of ~~50 days. The programming, operation and downloading procedures for all types of SmartSolo nodes are also similar.
16 -
17 -(% class="box infomessage" %)
11 +>(% class="box infomessage" %)
18 18  (((
19 -**Freight update, 2026: **Freight options for lithium-ion batteries are changing in 2025/2026 to comply with updated transport safety regulations. This will impact supply of IGU 16 (<100Wh) and BD3C (168Wh) nodes. Advice will be sought from freighters on a case-by-case basis while they implement new guidelines.
13 +**~ INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING **
20 20  )))
21 21  
22 -----
16 +== **Installation** ==
23 23  
24 -= **Programming Defaults** =
18 +* (((
19 +**Logbook Maintenance**: Document essential details:
25 25  
26 -The nodes must be programmed in the SoloLite software prior to use. The screenshots below show our recommended parameters for the 5 Hz (16HR-3C) and 5 second (BDC3-5) nodes.
21 +* Station name, latitude/longitude, team members, date/time.
22 +* Serial number (SN) of sensor, site notes.
23 +)))
24 +* **Node Placement**: Use biodegradable plastic bags for node protection.
25 +* **Orientation and Site Description**:
26 +** Compass measurements (adjust for inclination).
27 +** Detailed description of the site, including landmarks.
28 +* **Visibility and GPS Marking**:
29 +** Use distinctively colored flags for easy location.
30 +** Mark location with GPS; record in logbook and device.
31 +* **Photo Documentation**: Take multiple photos from various angles.
27 27  
28 -[[IGU16HR-3C programming screen set at 250 Hz. Ensure circled areas are set!>>image:5Hz_node_programming.labels.png||alt="IGU-16 3C programming screen"]]
33 += =
29 29  
30 -[[BD3C-5 programming screen set at 250 Hz. Ensure circled areas are set!>>image:5S_node_programming.labels.png||alt="BD3C-5 programming screen set at 250 hz. Ensure that the circled areas are set!"]]
35 += SmartSolo IGU 16HR 3C (5 Hz) Short Period Node =
31 31  
37 +blahblah
32 32  
33 -FIFO (first in, first out) data mode is safest as this will overwrite old data in case you forgot to clear the storage. At <= 250 hz you can fit 4++ months of data on these, shouldn't be an issue.
39 +== Sub-paragraph ==
34 34  
35 -Note that the samplerate is instead given in sample spacing, in milliseconds. 4 ms = 250 Hz, 1 ms = 1000 Hz, 10 ms = 100 Hz, ad nauseam.
36 36  
37 -Be sure to set the channel types to Seismic and the gain appropriately. For active source (i.e. explosions) you can leave the gain at 0, but for passive experiments some gain is purported to be helpful (although we have found this to be somewhat negligible). We can confirm that 6db for the broadband nodes and 24db for the short period works well.
42 +== ==
38 38  
39 -If you want recording to begin immediately, ensure that begin date is in the past by at least a few days. If you prefer to have a timed turn-on, then set the times as needed. **Be warned that recording will not begin until a GPS lock is achieved, so if you set it to a future turn-on but bury it too deeply, it may not record!**
40 40  
41 -In newer versions of the software there is a "power consumption" setting.. we are no sure what this does exactly, but the manual says it gives life a "boost" at the expense of about 3 db of resolution. Until this can be quantified a bit better it is not recommended.
45 += Smart Solo BD3C-5 (5 second) Broad-Band Node =
42 42  
43 -Storage type can be DLD (proprietary) or Miniseed. We assume the software works best with their proprietary format so prefer not to risk any issues. You can export to miniseed later.
47 +Lorem
44 44  
45 -GPS is best set to cycle mode (e.g. once per hour) instead of constant "always on". The clock drift on these are almost nil even if there is no sync at all, so it's best to conserve power.
49 +[[image:1705196270090-364.png]]
46 46  
47 -Bluetooth (BD3C-5 only) should be turned OFF to conserve power.
48 48  
49 -We recommend that the 16HR-3C be set to a gain of 24db for passive experiments and no higher than 250 Hz sampling rate unless there is an explicit reason to do so. The BD3C-5 should be set to a gain of 6db (which is the maximum allowed) for passive experiments (or 0 db if active).
52 +== GPS Considerations ==
50 50  
51 -{{info}}
52 -**Note that any applied instrument gain must be removed when exporting (e.g. to miniseed) after your deploy, **otherwise amplitudes will be a factor of either 15.84893192 (24db) or 2 (6db) too high!
53 -{{/info}}
54 +The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin layer of soil, but may struggle if the soil layer is too thick. The BD3C will not start recording without first attaining a GPS lock.
54 54  
55 -= **Fieldwork Preparation** =
56 += Keeping the Instruments Clean =
56 56  
57 -(% class="box warningmessage" %)
58 -(((
59 -**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**
58 +Use a (**landfill**, not //compost//) degradable bag when installing to keep the instrument clean. This will save you many hours of time cleaning them in preparation for their return. [[Here is a video>>url:http://auspass.edu.au/field/bd3c_removal.mp4]] demonstrating its effectiveness.
60 60  
61 -**Assume ~~1 Tb of storage for both raw and exported data per 50 nodes @ 250 Hz & 30 days. One node recording at 250 Hz for 30 days tends to create about 3 Gb of miniseed data.**
62 62  
63 -**We have had good experience with the 4Tb Samsung T7 Shield drives.**
64 -)))
61 += Charge Time, Instrument Life, and Charge During Storage & Shipping =
65 65  
66 -== Magnets ==
63 +Both nodes take about 6-8 hours to charge from flat and hold their charge reasonably well, however you may benefit from a "top up" charge immediately prior to deploy. The instruments should last around 30 days per cycle (recording at 250hz) with GPS on cycle on and bluetooth disabled.
67 67  
68 -If you are short on magnets, you may find it easier and a lot cheaper to buy magnets in Australia. AMF Magnetics is a good retailer, and [[this item>>https://magnet.com.au/collections/shop?q=23012B]] seems to work well. It is also advantageous to use smaller magnets and store/carry them individually in your back pocket (as well as stick them to various places in your field vehicle, etc).
65 +Upon retrieval, the instruments should not be stored flat as this will damage the batteries. It is recommended to charge them back up "to orange" such that they are charged around ~~50-60%. This is also acceptable for shipping.
69 69  
70 -== Animal-Proofing ==
71 71  
72 -We have experienced interference from animals (foxes, dogs, goats) digging up and carrying nodes off for tens or hundreds of metres. It is helpful to minimise human and food smells (particularly on the rope handles) when working in areas where this is a risk. Or, wipe down affected nodes with 50-80% methylated spirits if extensive handling can not be avoided.
68 += Best Practices and Guide =
73 73  
74 -If you come to collect your node and it is missing~-~- **LOOK FOR IT!** It may not have gotten far. We have found dozens of nodes by spending 15 minutes looking for them.
70 +== Install ==
75 75  
76 -= External Power =
72 +Logbook is required (used again for pick up & metadata creation)
77 77  
78 -Both the 5Hz IGU-16HR and 5s BD3C-5 can be optionally powered via external battery via either a replacement bottom half (the 5Hz nodes) or a battery cable accessory (BD3C-5) using standard lead acid batteries from 9-36v. We have done preliminary testing at 250 Hz with a standard 12v deep cycle AGM battery:
74 +- station name
79 79  
80 -- BD3C-5: ~~2 days of recording per 1 Ah
76 +- lat / long
81 81  
82 -- IGU16-HR 3C:  ~~3.5 days of recording per 1 Ah
78 +- team members
83 83  
84 -- IGU16-HR 1C: ~~7 days of recording per 1 Ah
80 +- date and local time
85 85  
86 -Of course, these can also be fit with a solar panel & charge controller which would then theoretically keep them going indefinitely (limited only by the disk storage, which at 250 Hz could be on the order of 12 months).
82 +- SN of sensor
87 87  
88 -= **Installation** =
84 +- notes on site
89 89  
90 -(% class="box infomessage" %)
91 -(((
92 -**Field logs are a critical component of fieldwork and this is especially the case for large N nodal deploys. Take notes!**
93 -)))
86 +Place nodes in thick (“landfill biodegradable”) plastic bags in the hole
94 94  
95 -== 1. Logbook documentation ==
88 +Take compass measurement away from node and fences [make sure to adjust inclination angle]
96 96  
97 -(((
98 -**Essential Details** for field logs:
90 +Take many photos from the site from different angles 
99 99  
100 -* Station name
101 -* Latitude, longitude, elevation
102 -* Names of team members present
103 -* Date and both local & UTC time of installation/removal
104 -* Serial number (SN) of the TOP HALF of the sensor (if a BD3C-5, there is only one serial number)
105 -* Detailed notes on the site conditions and setup, anything else that will be helpful to find it again ("by the fence", "south of rock", etc)
92 +Add a precise site description to the notes such as distances and orientations from landmarks 
106 106  
107 -[[HERE>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]] is an example logsheet that works well for nodes, feel free to print and use!
94 +It will be very helpful in locating the instrument if you place a flag next to it, preferably in a color other than green or yellow.
108 108  
109 -== 2. Burial ==
96 +Make a mark (digital) of the instrument's location using a GPS device. Record the location both in your paper notes and on the GPS device.
110 110  
111 -**ALL nodes should be buried flush with the ground, no exceptions**. If the node is sticking up the data data quality will be significantly reduced (especially the horizontal channels, see [[below>>https://auspass.edu.au/xwiki/bin/view/Instrumentation/SmartSolo%20Nodes/#HIGU-16Horizontalnoise26howtoavoid]]). It also catches wind, makes them more visible, etc. But mostly it makes the data bad.
98 +Download the GPS (Garmin) file to a laptop and share drive to share with other GPS devices
112 112  
113 -//Don't be lazy. Do it right. //
100 +Share photos in a shared location (Google photos, OneDrive, Dropbox, etc), but most useful are those added to a Google Maps/Earth location
114 114  
115 -[[An example of what not to do.>>image:1786503344572-296.jpg||data-xwiki-image-style-alignment="center" height="341" width="404"]]
102 +Create metadata .xml file
116 116  
117 -[[North channel PSD of the sensor in the picture above (it is not good)>>image:1786503812585-338.02.28 PM.png||data-xwiki-image-style-alignment="center" height="244" width="451"]]
118 118  
119 -== 3. Node Placement ==
120 -)))
105 +== Removing/Demob ==
121 121  
122 -**Site Analysis**:
107 +Download and then use the GPS file to locate the node 
123 123  
124 -* **Take compass measurements away from the sensor as it will affect your measurement. Use a stick or shovel to help align.**
125 -* Take photographs from various angles to document the site setup thoroughly. Have a colleague stand next to it pointing at it.
126 -* Include a detailed site description in your notes.
109 +Use Google Maps / Google Earth to create a kmz file that can then be imported onto your phone.  
127 127  
128 -== 4. GPS Considerations ==
129 129  
130 -(% class="wikigeneratedid" %)
131 -The GPS antenna is at the top and center of the unit, and will (usually) only receive signal with a clear sky view directly above. The signal is able to penetrate plastic and terracotta planters and a thin (2 cm?) layer of soil, but may struggle if the soil layer is too thick. **These nodes will not start recording without attaining a GPS lock** and repeated attempts will excessively drain the battery.
112 +Upload photos of the site  
132 132  
133 -== 5. Visibility and Location Marking ==
114 +- station name
134 134  
135 -**Flag Placement**: Position a flag, preferably in a bright color (avoid green or yellow), near the instrument to aid in its future location.
116 +- latitude
136 136  
137 -**GPS Marking**:
118 +- longitude
138 138  
139 -* Use a GPS device to mark the instrument's exact location. Most modern cell phones can get to about a 3m error with their internal GPS also; you can probably also get away with investing a few dollars in a good app that shows error and lets you log markers.
140 -* Also write the GPS down on paper (ie your [[LOG SHEET>>http://auspass.edu.au/field/NODES_blank_fieldlog.pdf]]).
120 +- elevation
141 141  
142 -== (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)6. Charge Time, Pre-Deployment & Post-Deployment(%%) ==
122 +* SN of sensor – SN of battery (optional)
123 +* Site notes and name of location (e.g. Richards garden, Te Mini steam field eastern side) 
143 143  
144 -* **Charging Duration**: Both types of nodes take approximately 6-8 hours to fully charge from a flat state.
145 -* **Pre-Deployment Charging**:
146 -** Although the nodes hold their charge well, it's beneficial to give them a "top up" charge before deployment.
147 -* **Operational Duration**:
148 -** When recording at 250 Hz, with GPS on and Bluetooth disabled, the instruments are expected to last about 30 days per charge cycle. If they are set to run only overnight, this can be extended to 60 days.
125 +Upload photos into Google Earth and on a shared drive
149 149  
150 -* **Post-Retrieval Charging**:
151 -** After retrieval, charge the instruments to about 50-60% (indicated by ORANGE LED) unless they are to be immediately re-deployed or transported.
152 -* **State of Charge (SoC) for Storage**:
153 -** Maintain a battery charge level of around 50-60% (i.e., ORANGE) for storage.
154 -** This charge level is recommended to prevent battery damage, and should be checked every six months.
155 -** Nodes should //__not be stored at full-charge (GREEN), or 0-charge (RED).__//
156 -** Storage at 0-charge damages lithium batteries**.**
157 -* **SoC for Transport:**
158 -** Charge levels for transport will be advised by the freighter. The required SoC will depend on volume and transport method (air, land, sea).
127 +Before removing the instrument have your compass, tape, marker, pen, clipboard, logbook and compass ready (in tote bag!). 
159 159  
160 -(((
161 -== 7. Data Sharing and Metadata Creation ==
162 -)))
129 +Write the station name and the instrument’s serial number, along with 'D' and 'C' and ‘R’, each next to a box to indicate 'download' and 'charge'. Stick this label to the top of the instrument. When dealing with dozens or hundreds of these you WILL start to mix them up after a while! Having an easy visual cue keep them sorted will save you a great deal of confusion later on.
163 163  
164 -**GPS Data**:
131 +Take a photo of the entire setup node with the label on it + compass 
165 165  
166 -* Ensure you have __carefully documented__ precise lat/lon locations for each station.
133 +Use existing field logbook to note time, SN and station name plus any notes – including any issues with orientation or level or anything else
167 167  
168 -**Photo Sharing**:
169 169  
170 -* It is strongly encouraged to take pictures of each site and upload these to a shared platform (OneDrive, Dropbox, etc.).
136 +== Charging ==
171 171  
172 -**Metadata File**:
138 +Clean node prior to charging and harvesting the data
173 173  
174 -* Create and organize metadata according to the [[ANU metadata standard txt file>>attach:example_metadata.txt]]. This is going to be particularly important if you are reusing nodes at different sites... not documenting the serial numbers (of the **top half** of the node) and the times they were deployed can lead to station mix-ups.
140 +Remove battery (and spike) from the sensor by twisting the spike part of the instrument
175 175  
176 -== 8. Additional Best Practices ==
142 +Set 16 nodes into the charging box (spikes up)
177 177  
178 -* **Training and Familiarisation**: Make sure all team members are adequately trained in using the GPS devices, compass use, and other equipment to ensure consistent and accurate data collection.
144 +Red lights on the box next to the batteries will come on and remain a steady red light while charging. This will change to orange, then to green, then to flashing green when fully charged.
179 179  
180 -----
146 +This is a good time to check the "C" box on your temporary labels to mark that the unit has been charged
181 181  
182 -= **Seismic Station Demobilization and Documentation** =
148 +[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center"]]
183 183  
184 -1. (((
185 -**Preparation for Demobilization**:
186 186  
187 -* Before starting the demobilization process, ensure you have a compass, tape, marker, pen, masking tape, clipboard, logbook, and compass ready in your tote bag.
188 -)))
189 -1. (((
190 -**Locating the instrument**:
191 191  
192 -* Use the downloaded GPS file to accurately locate the node for demobilization.
193 -* Import this KMZ file onto your phone for easy reference and location tracking.
194 -* Utilize Google Maps or Google Earth to create a KMZ file of the station’s location.
195 -)))
196 -1. (((
197 -**Labeling Instruments for Demobilization**:
152 +== Downloading and Converting Data to MiniSeed ==
198 198  
199 -* Write the station name and the instrument’s serial number on a masking tape label to apply to the top of the node.
200 -* Add markers 'D' (for download), 'C' (for charge), and ‘R’ (for removal) next to checkboxes on the label.
201 -* Affix this label to the top of the instrument to avoid confusion during the charging and downloading data.
202 -)))
203 -1. (((
204 -**Photographing the Setup Node**:
205 205  
206 -* Take a photo of the entire setup node with the __//label//__ and __//compass visible//__.
207 -* This photo serves as a final record of the instrument’s condition and orientation at the time of removal.
208 -)))
209 -1. (((
210 -**Logging Demobilization Details**:
155 +The first thing to do is to register the nodes in the system, so the software can recognize them. To do this, go to the folder where the “SmartSoloApps SoloLite” was installed. Then right-click the deviceconfig.exe program to “run as an administrator” and save the file to the directory of “deviceconfig” (snapshot below). Note that to avoid registering the same node twice, you can simply replace the file each time you do the registration.
211 211  
212 -* Use the field logbook to note the time of demobilization, serial numbers, and station name.
213 -* Record any observations or issues related to the instrument’s orientation, level, or any other relevant factors.
214 -)))
215 -1. (((
216 -**Final Checks and Equipment Removal**:
157 +[[image:1705195543887-977.png]]
217 217  
218 -* Before physically removing the instrument, double-check that all necessary data has been downloaded and all photos and notes have been taken.
219 -* Carefully dismantle and pack the equipment, ensuring that all components are accounted for and securely stored for transport.
220 220  
221 -
222 -)))
160 +Then open the “SoloLite” software, and just go to “File” to make a new project. In this case, you do not need to find the exact 16 nodes that were grouped for script writing. Do not worry about the settings for the seismic recordings for the next window to pop up, as the only way to reset the instruments (e.g., sampling rate, gain etc) is to write script to re-program them.
223 223  
224 -[[image:1706153556166-231.jpeg||data-xwiki-image-style-alignment="center" height="345" width="460"]]
162 +[[image:1705195543890-537.png||data-xwiki-image-style-alignment="center"]]
225 225  
226 -----
227 227  
228 -= **Charging Procedure for Seismic Nodes** =
165 +Once you create the new project, your Data Transfer View panel on the bottom right of the window will show these nodes that have properly connected to the data harvest, including series number, data size etc. It is okay if the “Prospect not matched”, which simply means the project you just created does not match the one you made to program them. Simply select all these nodes, and right click to “force download”, which will initiate the downloading process. Once they are done, you will see new folders created for each slot at your Downloaded Data panel on the top left of the window.
229 229  
230 -(((
231 -== 1. Preparation for Charging: ==
167 +[[image:1705195543891-334.png||data-xwiki-image-style-alignment="center"]]
232 232  
233 -* Before charging, ensure each node is clean. This involves removing any dirt or debris to maintain the integrity of the equipment and ensure effective charging.
234 -)))
169 +At this stage, it means that the raw DLL data of the recording has been downloaded successfully to your local machine. To output data in readable format, such as SAC or miniSEED, click the “Tool” menu and select “export seismic data”. The parameters here should be straightforward to set and tailored to personal reference.
235 235  
171 +(% class="box warningmessage" %)
236 236  (((
237 -== 2. Disassembling the Node: ==
238 -
239 -* For the IGU-16HR, remove the battery section (bottom half) from the sensor by unscrewing the spike section counter-clockwise.
173 +**Please make sure that data is exported as "COUNTS" and NOT "mV"!**
240 240  )))
241 241  
176 +(% class="box warningmessage" %)
242 242  (((
243 -== 3. Setting Nodes in the Charging Box: ==
244 -
245 -* Connect to a safe indoor power supply, and turn on (red rocker switch).
246 -* Charging will begin automatically when nodes are inserted in the charging rack.
247 -* Place IGU-16HR battery sections upside-down in the rack, oriented with the terminal connectors.
178 +**Furthermore you must also set "Remove Gain" to the same decibel gain setting that was set during programming! ANU always set this to 18 db (double check) for all types of nodes.**
248 248  )))
249 249  
250 -(((
251 -== 4. Monitoring the Charging Process: ==
181 +A list of ANU group preferred parameters can be found at the end of this session. One thing to note is that the “Sample Interval” must be set exactly to this used to reset the nodes. Once you are done with the setting, click “prepare” before “run”. If everything works correctly, you should see the reformatting process from the small panel on the bottom left of this popped up window.
252 252  
253 -* Lights adjacent to the batteries will illuminate, indicating that charging is underway.
254 -* Observe the transition of the lights from steady RED to ORANGE, then GREEN, and finally to FLASHING GREEN. A flashing green light indicates the batteries are fully charged.
255 -)))
183 +Now the data should be ready. Then you can select these data and right click to output the GPS information associated with them.
256 256  
257 -(((
258 -== 5. Updating Charge Status: ==
185 +[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center"]]
259 259  
260 -* During the charging period, take this opportunity to update the status of each unit. Check the //"C"// box on your temporary labels to indicate that the unit has been successfully charged.
261 -* This step is crucial for tracking the charging status of multiple units, especially when handling a large number of nodes.
262 -)))
187 +When downloading, all the green lights on the nodes will blink. The associated red lights on the rack will flash when it is downloading, and make sure to disconnect the nodes before you unplug anything. Be careful: if the laptop goes to sleep, the download process will pause.
263 263  
264 -[[IGU 16-HRcharger (left) and harvester (right)>>image:1705195933422-337.png||data-xwiki-image-style-alignment="center" height="299" width="530"]]
265 -
266 -
267 -
268 -
269 -{{{
270 - }}}
271 -
272 -----
273 -
274 -= **Downloading and Converting Seismic Data to MiniSeed Format** =
275 -
276 -(% class="wikigeneratedid" %)
277 -SmartSolo provides the following powerpoint for SmartSolo node programming and operation. Note that ANSIR only uses a portion of their process for our own uses: [[https:~~/~~/nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf>>url:https://nappe.wustl.edu/smartsolo/files/smartsolo_online_training.pdf]]
278 -
279 -== Connection tips: ==
280 -
281 -Connecting SmartSolo nodes to their harvesters and having SoloLite recognise them can be a bit tricky, here are some tricks to help register and program them easier:
282 -
283 -* Place the node on the harvester gently, then firmly press it down onto the pins.
284 -* Place all nodes onto the harvester before trying any troubleshooting, as they may not show up while the SoloLite software is running. Once all are connected, try restarting the software for them to be recognised.
285 -* If a node is refusing to connect, try it with another slot. It is easiest if you place all 16 nodes on the harvester, and swap any nodes that refuse to connect with each other.
286 -* Nodes will likely not show up in the order that they should, though this is not an issue. E.g, a node in slot 6 on the harvester may show up in port 13 in the SoloLite software. Annoying, but it doesn't matter so long as you keep track of what's been harvested!
287 -
288 -
289 -
290 -== Node Registration and Software Setup ==
291 -
292 -1. (((
293 -**Registering Nodes in the System**:
294 -
295 -* To begin, register the nodes in the system so the software can recognize them.
296 -* Navigate to the installation folder of “SmartSoloApps SoloLite”.
297 -* Right-click on deviceconfig.exe and choose “run as an administrator”. Save the file to the “deviceconfig” directory (refer to the snapshot below).
298 -* To avoid double registration, replace the file each time you register a new node.
299 -)))
300 -1. (((
301 -**Creating a New Project in SoloLite**:
302 -
303 -* Open the “SoloLite” software.
304 -* Go to “File” and create a new project. Don't worry about finding the exact 16 nodes used in script writing.
305 -* Ignore the settings for seismic recordings in the subsequent window. Resetting instruments (e.g., sampling rate, gain) requires reprogramming via script.
306 -)))
307 -
308 -== File structure ==
309 -
310 -There are essentially three main folders where relevant PROSPECT and PROJECT DATA is stored. Individual projects will be found as subfolders in these.
311 -
312 -=== SOLOLITE ===
313 -
314 -This folder stores SoloLite config files and parameters. Nothing too important stored here, you can always start over and re-create this.
315 -
316 -=== DCCDATA ===
317 -
318 -This folder stores the RAW data you have harvested from the nodes. The data will still be on the nodes (unless you erased it) in case of emergency, but regardless, this is the folder you want to back up and save somewhere.
319 -
320 -If you had a weird time harvesting a node, you can always manually copy it as if it were a USB stick and place it into this folder manually. The structure is: //C:/DCCDATA/prospect_name/project_name/SERIALNUMBER/label(usually a timestamp but can be anything)//
321 -
322 -Then in the SoloLite software, go to tools > Reanalyze Seismic Data
323 -
324 -=== SOLODATA ===
325 -
326 -This folder stores **exported** (e.g. miniseed) data. It is structured similarly. If your DCCDATA is intact, this can always be re-created if need be.
327 -
328 -
329 -== Data Downloading Process ==
330 -
331 -1. (((
332 -**Initiating Data Download**:
333 -
334 -* Once a new project is created, the Data Transfer View panel will display connected nodes with details like series number and data size.
335 -* If “Prospect not matched” appears, it simply means the new project doesn’t match the original programming project. This is not a concern.
336 -* Select all nodes and right-click to “force download”. This starts the download process.[[image:Smartsolo harvesting #4 copy.png]]
337 -* Completed downloads will appear as new folders in the Downloaded Data panel.
338 -)))
339 -1. (((
340 -**Exporting Data in Readable Format**:
341 -
342 -* Go to the “Tool” menu and select “export seismic data”.
343 -* Tailor other parameters to project preference and ensure "Sample Interval" matches the setting used during node reset (note: the standard used by ANU is 4ms, or 250hz)
344 -* (% class="box warningmessage" %)
189 +(% class="box infomessage" %)
345 345  (((
346 -**Ensure export data is set to "COUNTS" (int32), not "mV" (float). This is critical!**
191 +**INVEST IN FAST EXTERNAL HARD DRIVES – DO NOT LET THIS BE THE LIMITATION OF DATA HARVESTING**. USB-C, USB 3.0, and 4+ Tb of space are highly recommended!
347 347  )))
348 -* Set "Remove Gain" to the same decibel gain as during programming. By default ANU sets this to 24db for short period nodes (a scaling factor of 15.848932), and 6db (a factor of 2.0) for broadband nodes.
349 -* Set "Remove DC" to "Yes" to centre the data around the zero value
350 -* Set the correct Start Time (UTC) and End Time (UTC) of the project to prevent the unnecessary export of older data
351 -* [[image:Smartsolo harvesting #9 copy.png]]
352 -* Click “prepare” followed by “run” to start reformatting. Monitor this process in the small panel at the bottom left.
353 -* The data will be exported to the SOLODATA folder. For a windows system, the following file explorer page is where you must navigate to to locate your project folder[[image:Smartsolo harvesting #8 copy.png]]
354 -)))
355 355  
356 -== Smart Solo IGU-16HR Polarity Notice ==
194 +When downloading, ensure that all metadata is saved along with the file.
357 357  
358 -See [[5Hz Node Polarity Issues>>https://auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodePolarityIssues]] for discussion. If data is headed to AusPass, we prefer to invert the IGU-16HR channel data manually rather than in the SoloLite software or inverting the response metadata.
196 +Start and endtime: the system will automatically find the earliest time of the data and set that as the starting time. However, you can set the time a day earlier with a sharp start of 00:00:00. In this case, all the outputted data segments will be 24 hours long starting from midnight.
359 359  
360 -**The BD3C-5 data does not require any sort of polarity inversion.**
198 +//Once downloaded, mark the "D" box on your temporary labels!//
361 361  
362 -== 18 Leap Second bug ==
200 +== Converting data ==
363 363  
364 -Not so much a //bug// as much as "a thing that can happen if your SoloLite installation is corrupted". If you notice your data has large constant time offsets, you should suspect that the number of leap seconds has not been accounted properly. There is a file "smartsoloconfig.xml" that needs to be present in "C:\SmartSoloApps SoloLite" (e.g. the main program directory) that dictates the leap second offset for the last two data ranges. Since 2017-01-01, this is 18 seconds. At some point in the next few years it will be 19 seconds.
202 +Check the data all have been converted to miniseed correctly 
365 365  
366 -If this file is missing, just create a new one structured like so, name it "smartsoloconfig.xml" and put it in your main program directory. Then, Reanalyze your data (tools > Reanalyze seismic data) and your data should have the correct time. You can also do this manually, if you want. The offset is 18 seconds precisely.
204 +– 3 files per station per day 
367 367  
368 -{{code language="none"}}
369 -<?xml version="1.0" encoding="UTF-8"?>
370 -<config>
371 - <leapsecond>
372 - <interval>
373 - <start_time>2017-01-01#00:00:00</start_time>
374 - <end_time>2999-12-31#23:59:59</end_time>
375 - <second>18</second>
376 - </interval>
377 - <interval>
378 - <start_time>1970-01-01#00:00:00</start_time>
379 - <end_time>2017-01-01#00:00:00</end_time>
380 - <second>17</second>
381 - </interval>
382 - </leapsecond>
383 - <GPS_distance_threshold_degree>
384 - 4e-5
385 - </GPS_distance_threshold_degree>
386 -</config>
387 -{{/code}}
206 +* Files are the same size (NOTE if having memory issues one or more of the components may have 0-1 kb)
207 +* ~~ 5 Gb / node / month
388 388  
209 +//Tick ‘R’ box on the node label//
389 389  
390 -== Handling Nodes During Download ==
391 391  
392 -1. (((
393 -**Monitoring Download Indicators**:
212 +== Cleaning ==
394 394  
395 -* During download, green lights on nodes will blink, and associated red lights on the rack will flash.
396 -* Disconnect nodes properly before unplugging anything.
397 -* Be cautious: if the laptop enters sleep mode, the download will pause.
398 -)))
399 -1. (((
400 -//**Investment in Storage Hardware**~://
214 +If the nodes are placed in a thick plastic bag at the time of installation, the cleaning procedure should be straightforward. If not you have a lot of work to do before they are returned to us!
401 401  
402 -* (% class="box warningmessage" %)
403 -(((
404 -* **Use fast external hard drives to avoid limitations in data harvesting.**
405 -
406 -* **Recommended specifications: USB-C, USB 3.0, and 4+ Tb of space.**
407 -* **The USB type for the harvester is TYPE-A, the typical normal rectangular shape.**
216 +
408 408  )))
409 -)))
410 -1. (((
411 -**Metadata and Time Settings**:
412 412  
413 -* Ensure all metadata is saved with the file.
414 -* System auto-determines the earliest data time as the start time. You can set it a day earlier at 00:00:00 for 24-hour data segments starting from midnight.
415 -)))
416 -1. (((
417 -**Finalizing the Download**:
418 418  
419 -* After downloading, mark the //"D"// box on your temporary labels to indicate completion.
420 -)))
421 -
422 -
423 -
424 -
425 -[[Caption>>image:1705195543887-977.png||data-xwiki-image-style-alignment="center" height="534" width="632"]]
426 -
427 -
428 -
429 -
430 -[[Caption>>image:1705195543890-537.png||data-xwiki-image-style-alignment="center" height="397" width="665"]]
431 -
432 -
433 -
434 -[[Caption>>image:1705195543891-334.png||data-xwiki-image-style-alignment="center" height="379" width="650"]]
435 -
436 -
437 -
438 -[[image:1705195543898-365.png||data-xwiki-image-style-alignment="center" height="467" width="674"]]
439 -
440 -----
441 -
442 -= Copying raw MiniSeed data without the Software =
443 -
444 -Lately we have been advocating for not writing to the proprietary DFD format (we don't know how this is structured) in the event that the software is misbehaving or one wants to use a linux machine or for whatever reason. This involves simply reading the devices as a mounted USB device and copying off the .MiniSeed files manually~-~- easy enough!
445 -
446 -However please note the filename and channel convention:
447 -
448 -3 Trace(s) in Stream:
449 -XX.TEST..LHX | 2026-09-01T03:26:14.000000Z - 2026-09-07T02:15:01.996000Z | 250.0 Hz, 128532000 samples
450 -XX.TEST..LHY | 2026-09-01T03:26:14.000000Z - 2026-09-07T02:15:01.996000Z | 250.0 Hz, 128532000 samples
451 -XX.TEST..LHZ | 2026-09-01T03:26:14.000000Z - 2026-09-07T02:15:01.996000Z | 250.0 Hz, 128532000 samples
452 -
453 -= Instrument Response =
454 -
455 -We are aware that there are various different published responses for these instruments and trust very few of them. One has to be careful with how polarity is handled between groups as well, and if one is working in integer counts (the ANSIR default) or mV (unclear why anyone would use this as it makes file sizes enormous). The response information published below is in **counts** and seems to fit well in huddle tests. Note that the response is the same for all channels and all units (e.g. there are no bespoke calibrations!), all appear to be sample rate insensitive, and the IGU data has been inverted (multiplied by -1) as described here: [[5Hz Node Polarity Issues>>https://auspass.edu.au/xwiki/bin/view/Data/AusPass%20Data/#HSmartSoloNodePolarityIssues]]
456 -
457 -== IGU 16HR-3C ==
458 -
459 - '16HR3C': {'poles':[(-22.211059+22.217768j), (-22.211059-22.217768j)],
460 - 'zeros':[0j, 0j],
461 - 'gain':1,
462 - 'sensitivity': 257019225.55108312}
463 -
464 -[[X axis is samples (.01 s), Y axis is velocity (m/s), 0.5-5 Hz filter>>image:16HR_Z_huddle.png||alt="IGU16_Z_huddle.png"]]
465 -
466 -[[X axis is samples (.01 s), Y axis is velocity (m/s), 0.5-5 Hz bandpass filter>>image:16HR_N_huddle.png||alt="IGU16_N_huddle.png"]]
467 -
468 -== IGU 16-1C ==
469 -
470 -The 1C nodes seem to have the same response as the 3-channel IGU-16HR-3C (above), however the response posted at IRIS-NRL seems to imply that there is no poles and zeros information (e.g. a flat/linear response). This is 100% not so.
471 -
472 -[[IGU-16 1C, X axis is samples (.01 s), Y axis is velocity (m/s), 0.5-5 Hz bandpass filter. Seems to be same response as IGU-16HR-3C.>>image:16HR1C_Z_huddle.png||alt="IGU16_1C_Z_huddle.png"]]
473 -
474 -== BD3C-5 ==
475 -
476 - 'BD3C': {'poles':[(-1720.4+0j), (-1.2+0.9j), (-1.2-0.9j)],
477 - 'zeros':[(14164+0j), (-7162+0j), 0j, 0j],
478 - 'gain':1.69726e-05,
479 - 'sensitivity': 702651512.6046528}
480 -
481 -Above 0.5 Hz, the BD3C-5 response fits well:
482 -
483 -[[X axis is samples (.01 s), Y axis is velocity (m/s), 0.5-5 Hz filter>>image:BD3C_Z_huddle.0.5.png]]
484 -
485 -[[X axis is samples (.01 s), Y axis is velocity (m/s), 0.5-5 Hz bandpass filter>>image:BD3C_N_huddle.0.5.png]]
486 -
487 -(% class="wikigeneratedid" %)
488 -Below the corner frequency (0.2 Hz) the phase response still fares well, but amplitude response may need to be dialed in a bit (it seems a bit high). We are working to try to calibrate this a bit better. In the next two figures the filter is **0.1** to 5 Hz:
489 -
490 -
491 -[[BD3C **0.1 **to 5 Hz bandpass filter>>image:BD3C_Z_huddle.0.1.png]]
492 -
493 -[[BD3C **0.1** to 5 Hz bandpass filter>>image:BD3C_N_huddle.0.1.png]]
494 -
495 -== IGU-16 Horizontal noise & how to avoid ==
496 -
497 -The** 5 Hz nodes** are susceptible to horizontal noise due to the placement of geophones in the units, **but this can be mitigated by completely burying the units flush with the ground.** In the below example, the node was set on the floor of our basement set on its plastic carrying case support. As such the amount of horizontal noise noticeably increases above ~~ 10Hz.
498 -
499 -[[IGU-16HR-3C Power spectrum huddle test vs a CMG-6TD (S1) and TC120/Centaur combo. The N and E channels have excess noise above 10Hz due to "sticking up" out of the ground.>>image:IGU16_spectrum.png]]
500 -
501 -(% class="wikigeneratedid" %)
502 -The BD3C-5 nodes do not have this issue:
503 -
504 -[[BD3C-5 test, as above. There is no additional noise on the horizontal channels.>>image:BD3C_psd.png]]
505 -
506 -= **Cleaning** =
507 -
508 -When assembled, the nodes are water resistant but not submersible. They can handle a good spray and wipe-down. A stiff plastic brush is helpful to reach areas between the metal spikes on the bottom.
509 -
510 -= **Weights (for shipping)** =
511 -
512 -The weights of bags of nodes, as well as data harvesters and node chargers, are listed below:
513 -
514 -1 bag + 6*IGU-16HR nodes: 18 kg
515 -
516 -1*IGU-16HR data harvester: 21.5 kg
517 -
518 -1*IGU-16HR charger: 26.3 kg
519 -
520 -1*BD3C-5 charger (with and without 16 cables): 21 kg / 14.5 kg
521 -
522 -1 case + 5*BD3C-5 nodes: 22 kg (aggregate battery weight <5kg, 168Wh)
523 -
524 -1 case + 6*BD3C-5 nodes: 25 kg (aggregate battery weight >5kg, 168Wh)
525 -)))
526 -
527 527  (% class="col-xs-12 col-sm-4" %)
528 528  (((
529 529  (% class="box" %)
... ... @@ -530,11 +530,24 @@
530 530  (((
531 531  **Contents**
532 532  
533 -{{toc/}}
534 -
535 -
226 +(% class="wikitoc" %)
227 +* [[SmartSolo IGU 16HR 3C (5 Hz) Short Period Node>>path:#HSmartSoloIGU16HR3C285Hz29ShortPeriodNode]]
228 +** [[Sub-paragraph>>path:#HSub-paragraph]]
229 +** [[ >>path:#H]]
230 +* [[Smart Solo BD3C-5 (5 second) Broad-Band Node>>path:#HSmartSoloBD3C-5285second29Broad-BandNode]]
231 +** [[GPS Considerations>>path:#HGPSConsiderations]]
232 +* [[Keeping the Instruments Clean>>path:#HKeepingtheInstrumentsClean]]
233 +* [[Charge Time, Instrument Life, and Charge During Storage & Shipping>>path:#HChargeTime2CInstrumentLife2CandChargeDuringStorage26Shipping]]
234 +* [[Best Practices and Guide>>path:#HBestPracticesandGuide]]
235 +** [[Install>>path:#HInstall]]
236 +** [[Removing/Demob>>path:#HRemoving2FDemob]]
237 +** [[Charging>>path:#HCharging]]
238 +** [[Downloading and Converting Data to MiniSeed>>path:#HDownloadingandConvertingDatatoMiniSeed]]
239 +** [[Converting data>>path:#HConvertingdata]]
240 +** [[Cleaning>>path:#HCleaning]]
536 536  )))
537 537  
243 +
538 538  (% class="box" %)
539 539  (((
540 540  = SmartSolo [[BD3C-5>>url:https://smartsolo.com/cp-4.html]] =
... ... @@ -545,19 +545,15 @@
545 545  
546 546  |(% style="width:189px" %)**Frequency Band**|(% style="width:221px" %)5 Seconds to 150Hz
547 547  |(% style="width:189px" %)**Sensitivity**|(% style="width:221px" %)200 V/m/s
548 -|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)Φ158 x160mm(H)
254 +|(% style="width:189px" %)**Size (without spike)**|(% style="width:221px" %)158 x160mm
549 549  |(% style="width:189px" %)**Weight**|(% style="width:221px" %)2.8 kg
550 550  |(% style="width:189px" %)**Data Storage**|(% style="width:221px" %)64 Gb
551 -|(% style="width:189px" %)**Battery**|(% style="width:221px" %)(((
552 -Lithium-ion battery contained in equipment (168.84 Wh)
553 -
554 -UN3481 PI967 S1
257 +|(% style="width:189px" %)**Battery**|(% style="width:221px" %)Li_etc XXAh
555 555  )))
556 -)))
557 557  
558 558  (% class="box" %)
559 559  (((
560 -= SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]]3C =
262 += SmartSolo [[IGU-16HR>>url:https://smartsolo.com/cp-3.html]] =
561 561  
562 562  [[image:smartsolo node.jpg]]
563 563  
... ... @@ -564,114 +564,13 @@
564 564  [[image:smartsolo node 2.jpg]]
565 565  
566 566  |(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 1652Hz
567 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)76.7 V/m/s
568 -|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm(H)
569 -|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.4 kg
269 +|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)67.7 V/m/s
270 +|(% style="width:187px" %)**Size (with spike)**|(% style="width:224px" %)103mm(L) × 95mm(W) × 187mm
271 +|(% style="width:187px" %)**Weight**|(% style="width:224px" %)2.3 kg
570 570  |(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)64 Gb
571 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
572 -Lithium-ion battery contained in equipment (96.48 Wh)
573 -
574 -UN3481 PI967 S2
273 +|(% style="width:187px" %)**Battery**|(% style="width:224px" %)Li_etc XXAh
575 575  )))
576 -)))
577 577  
578 -(% class="box" %)
579 -(((
580 580  
581 -
582 -= SmartSolo [[IGU-16>>url:https://smartsolo.com/cp-3.html]]1C =
583 -
584 -
585 -[[image:Screenshot 2025-08-01 161027.png]]
586 -
587 -|(% style="width:187px" %)**Frequency Band**|(% style="width:224px" %)5 Hz to 413Hz
588 -|(% style="width:187px" %)**Sensitivity**|(% style="width:224px" %)80 V/m/s
589 -|(% style="width:187px" %)**Size (without spike)**|(% style="width:224px" %)95mm(L) × 103mm(W) × 118mm(H)
590 -|(% style="width:187px" %)**Weight**|(% style="width:224px" %)1.1 kg
591 -|(% style="width:187px" %)**Data Storage**|(% style="width:224px" %)8 Gb
592 -|(% style="width:187px" %)**Battery**|(% style="width:224px" %)(((
593 -Lithium-ion battery contained in equipment (38.48 Wh)
594 -
595 -UN3481 PI967 S2
596 596  )))
597 597  )))
598 -
599 -(% class="box" %)
600 -(((
601 -= SmartSolo BD3C-16 Portable Battery Charger =
602 -
603 -[[image:20250729_125049.jpg]]
604 -
605 -|**Dimensions (LxHxW)**|558 x 357 x 300mm
606 -|**Input rating**|100-210V - 50/60Hz
607 -|**Power**|1000W
608 -|**Weight**|14.5 kg
609 -|**Weight with cables**|21 kg
610 -)))
611 -
612 -(% class="box" id="HSmartSoloBD3C-16PortableBatteryCharger" %)
613 -(((
614 -= SmartSolo IGU-16 Portable Data Harvester =
615 -
616 -[[image:20250729_124747.jpg]]
617 -
618 -|**Dimensions (LxHxW)**|625 x 500 x 366mm
619 -|**Input rating**|100-210V - 50/60Hz
620 -|**Power**|100W
621 -|**Weight**|21.5 - 24 kg
622 -|**Capacity**|16 nodes
623 -|**Download Speed**|20MB/sec/slot
624 -)))
625 -
626 -(% class="box" %)
627 -(((
628 -= SmartSolo IGU-16 Portable Battery Charger =
629 -
630 -[[image:20250729_124644.jpg]]
631 -
632 -|**Dimensions (LxHxW)**|625 x 500 x 366 mm
633 -|**Input rating**|100-210V - 50/60 Hz
634 -|**Power**|640 W
635 -|**Weight**|26.3 kg
636 -|**Capacity**|16 nodes
637 -)))
638 -
639 -(% class="box" %)
640 -(((
641 -= SmartSolo BD3C-5 Carry Case =
642 -
643 -[[image:20250729_124957.jpg]]
644 -
645 -
646 -|**Dimensions (LxHxW)**|590 x 225 x 405 mm
647 -|**Weight**|8.2 kg
648 -|**Capacity**|6 nodes
649 -)))
650 -
651 -(% class="box" %)
652 -(((
653 -= SmartSolo IGU-16 3C Carry Bag =
654 -
655 -[[image:20250729_124502.jpg]]
656 -
657 -|**Dimensions (LxHxW)**|230 x 340 x 310mm
658 -|**Weight**|(((
659 -3.6kg (empty)
660 -
661 -18.0kg (full)
662 -)))
663 -|**Capacity**|6 nodes
664 -)))
665 -
666 -(% class="box" %)
667 -(((
668 -= SmartSolo IGU-16 1C Carry Bag =
669 -
670 -[[image:20250729_124558.jpg]]
671 -
672 -|**Dimensions (LxHxW)**|225 x 200 x 550mm
673 -|**Weight**|
674 -|**Capacity**|8 nodes
675 -)))
676 -)))
677 -)))
16HR1C_Z_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -92.1 KB
Content
16HR_N_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -88.4 KB
Content
16HR_Z_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -80.8 KB
Content
1706153266647-145.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -1.7 MB
Content
1706153354750-415.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -2.1 MB
Content
1706153556166-231.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.sima
Size
... ... @@ -1,1 +1,0 @@
1 -839.4 KB
Content
1786503344572-296.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -1.4 MB
Content
1786503808210-822.02.28 PM.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -437.8 KB
Content
1786503812585-338.02.28 PM.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -437.8 KB
Content
20250729_124502.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -318.3 KB
Content
20250729_124558.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -376.8 KB
Content
20250729_124644.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -528.0 KB
Content
20250729_124747.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -488.5 KB
Content
20250729_124957.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -532.5 KB
Content
20250729_125049.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -457.6 KB
Content
5Hz_node_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.KB
Size
... ... @@ -1,1 +1,0 @@
1 -109.8 KB
Content
5S_node_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.KB
Size
... ... @@ -1,1 +1,0 @@
1 -114.2 KB
Content
BB_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -111.5 KB
Content
BD3C_N_huddle.0.1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -65.9 KB
Content
BD3C_N_huddle.0.5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -68.4 KB
Content
BD3C_N_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -72.1 KB
Content
BD3C_Z_huddle.0.1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -64.3 KB
Content
BD3C_Z_huddle.0.5.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -52.5 KB
Content
BD3C_Z_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -52.1 KB
Content
BD3C_psd.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -73.7 KB
Content
IGU16_1C_Z_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -72.3 KB
Content
IGU16_N_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -65.7 KB
Content
IGU16_Z_huddle.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -67.4 KB
Content
IGU16_spectrum.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -65.0 KB
Content
SP_programming.labels.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -106.7 KB
Content
Screenshot 2025-08-01 161027.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -82.8 KB
Content
Smartsolo harvesting #4 copy.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -33.8 KB
Content
Smartsolo harvesting #4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -33.8 KB
Content
Smartsolo harvesting #6 copy.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -33.6 KB
Content
Smartsolo harvesting #8 copy.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -38.3 KB
Content
Smartsolo harvesting #8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -60.0 KB
Content
Smartsolo harvesting #9 copy.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.JackD
Size
... ... @@ -1,1 +1,0 @@
1 -28.7 KB
Content
example_metadata.txt
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -2.7 KB
Content
... ... @@ -1,46 +1,0 @@
1 -# AKL-HR Node Array (AHNA) code X5
2 -CITE: Name, Name, and Name. (2023). A Node Array [Data set]. International Federation of Digital Seismograph Networks. https://doi.org/10.7914/8jxr-7029
3 -
4 -#SITE START END LAT LONG ELEV SPS RECORDER S/N SENSOR S/N PROPERTY,LOCALITY,COUNTRY COMMENTS
5 -
6 -# INSTALL
7 -AKL01 20-05-2023T00:00 30-06-2023T00:00 -37.0471 175.5245 75 250 SSNODE_C 590001950 SSNODE_5S 590001950 "Te Puru,Hauraki,NZ"
8 -AKL02 20-05-2023T00:00 30-06-2023T00:00 -36.7476 175.5026 70 250 SSNODE_C 590001943 SSNODE_5S 590001943 "Coromandel Town,Hauraki,NZ"
9 -AKL03 20-05-2023T00:00 30-06-2023T00:00 -36.9694 175.5020 98 250 SSNODE_C 590002068 SSNODE_5S 590002068 "Te Mata,Hauraki,NZ"
10 -AKL05 19-05-2023T19:00 22-02-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001957 SSNODE_5S 590001957 "South Head South,Auckland,NZ" "site was disturbed"
11 -AKL06 19-05-2023T19:00 30-06-2023T00:00 -37.2459 175.3426 34 250 SSNODE_C 590001930 SSNODE_5S 590001930 "Back Miranda,Auckland,NZ"
12 -AKB05 02-05-2023T00:37 30-06-2023T00:00 -36.6651 175.4800 63 250 TSAWR TS085A TRILL120 4875 "Colville,Hauraki,NZ"
13 -
14 -# SERVICE 1
15 -AKL05 22-02-2023T00:00 30-06-2023T00:00 -36.5996 174.3312 102 250 SSNODE_C 590001999 SSNODE_.2S 590001999 "South Head South,Auckland,NZ" "swapped node to shortperiod"
16 -
17 -
18 -
19 -
20 -################### ANY LINE BEGINNING WITH # will be commented! Comments are good!
21 -
22 -
23 -# NOTES
24 -# the start/end time is not critical, but good to have. what IS critical are the times of instrument changes as this potentially affects response information
25 -# to mark equipment changes, add a new line with an updated start date (e.g. AKL05 above)
26 -# can use tabs or spaces, but spaces tend to look nicer. formatting ultimately doesn't matter too much so long as there is any sort of "white space" between the fields
27 -# if you don't know a serial number, put 999. if you don't know the elevation, put 0
28 -# for Nodes, put the same serial number for both Recoder and Sensor (since they are the same!)
29 -
30 -
31 -# EXAMPLE INSTRUMENT LABELS
32 -#LPR200 = ANU LPR-200 logger (beige box)
33 -#TSAWR = ANU TerraSAWR logger (yellow box)
34 -
35 -#TRILL120 = Trillium Compact 120s
36 -#TRILL20 = Trillium Compact 20s
37 -#TRILL120PH = Trillium Compact 120s PostHole
38 -#CMG6TD = Guralp 6TD
39 -#CMG3ESP = Guralp 3ESP
40 -#3DLITE = Lenarrtz 3D-LITE
41 -
42 -#SSNODE_C = output was in COUNTS (there is also SSNODE_MV, if you (accidentally!) output to millivolts etc)
43 -#SSNODE_5S = broadband (can also use SSNODE_BB)
44 -#SSNODE_.2S = shortperiod (can also use SSNODE_SP)
45 -
46 -#it doesn't matter too much what you use for equipment labels, so long as they are consistent and otherwise defined somewhere in the comments!
XWiki.XWikiComments[0]
Author
... ... @@ -1,1 +1,0 @@
1 -Mark Goldman
Comment
... ... @@ -1,1 +1,0 @@
1 -I can verify that the default orientation for the SmartSolo 3C nodes is positive values for case motion to the South, West, and downwards. We have co-located nodes with permanent stations and noticed this correlation when comparing waveforms.
Date
... ... @@ -1,1 +1,0 @@
1 -2026-07-09 10:45:51.967
XWiki.XWikiRights[0]
Allow/Deny
... ... @@ -1,1 +1,0 @@
1 -Allow
Groups
... ... @@ -1,1 +1,0 @@
1 -XWiki.XWikiAllGroup
Levels
... ... @@ -1,1 +1,0 @@
1 -comment
XWiki.XWikiRights[1]
Allow/Deny
... ... @@ -1,1 +1,0 @@
1 -Allow
Levels
... ... @@ -1,1 +1,0 @@
1 -comment
Users
... ... @@ -1,1 +1,0 @@
1 -XWiki.XWikiGuest