Skip to Content

Changes for page ANU Seismic Data Loggers

Last modified by robert on 2026/02/19 15:45
From version 73.1
edited by robert
on 2026/02/19 15:45
Change comment: There is no comment for this version
To version 71.1
edited by robert
on 2025/11/04 15:36
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -16,10 +16,8 @@
16 16  
17 17  At 100 Hz and with a GPS cable connected these loggers draw about 220 mW of power once the screen is off (higher sample rates draw more power but only marginally, < 5 mW). Adding a sensor (e.g. a Trillium Compact 120) increases this to approximately 400 mW, or 0.4 volt-amps. So, in theory 7 Ah battery should last about 10 days without a solar panel, but in practice it seems to be a bit closer to 8 which may be due to variability in power drain while in getting GPS locks.
18 18  
19 -For very sunny environments (latitudes < 30) a 20 Volt, 10 Watt solar panel should have no issue keeping these loggers alive over the summer months, and assuming unobstructed skies should also be fine over winter. **However** when possible a 20 Watt pane works best, especially as they usually cost only $10-20 more these days.
19 +For very sunny environments (latitudes < 30) a 20 Volts 10 Watt solar panel should have no issue keeping these loggers alive over the summer months, and assuming unobstructed skies should also be fine over winter. However there is no harm in using 20 or even a 40 Watt panel, especially for high latitudes, coastal regions, or areas without a full sky view. In theory up to a 60 Watt solar panel is fine, but we don't recommend anything over 40 Watts and that amount of power is already overkill.
20 20  
21 -40 Watt panels can also be used, and may be needed for extreme climates, or areas without a full sky view. 60 Watt panels have also been known to work, but this is now reaching the the limit of what the loggers can reasonably handle for extended periods and are not recommended for long term deploys.
22 -
23 23  (% class="box infomessage" %)
24 24  (((
25 25  Power issues are easy and cheap to solve relative to the cost of your experiment, don't skimp!
... ... @@ -60,7 +60,7 @@
60 60  
61 61  (% class="box warningmessage" %)
62 62  (((
63 -NOTE: the 2 at the very end is for "RECORD ON RESTART". The record on restart option ensures that if the logger dies and is powered back up whilst in the field (due to battery charging cycles or other causes) that the recording will resume. (# of blank spaces before this doesn't matter)
61 +NOTE: the 2 at the very end is for "RECORD ON RESTART". The record on restart option ensures that if the logger dies and is powered back up whilst in the field (due to battery charging cycles or other causes) that the recording will resume. (# of blank spaces before this doesn't matter)
64 64  )))
65 65  
66 66  (% class="wikigeneratedid" id="HTheformatforTSAWRloggersisshorter:" %)
... ... @@ -177,7 +177,7 @@
177 177  
178 178  = LogFile Conversion Script =
179 179  
180 -Both the TSAWR and LPR-200 write logging information as a binary "dat" file which includes GPS time syncs, temperatures, battery power, and position. To convert them into ASCII you can read, use [[THIS PYTHON SCRIPT>>http://auspass.edu.au/field/anusr_log.py]] (current version: 1.42, 02/2026).
178 +Both the TSAWR and LPR-200 write logging information as a binary "dat" file which includes GPS time syncs, temperatures, battery power, and position. To convert them into ASCII you can read, use [[THIS PYTHON SCRIPT>>http://auspass.edu.au/field/anusr_log.py]].
181 181  
182 182  = Instrument Response =
183 183  
... ... @@ -252,10 +252,6 @@
252 252  = References =
253 253  
254 254  * [[PDF Manual>>http://auspass.edu.au/field/LPR-200_Instruction_Manual.pdf]]
255 -
256 -[[TSAWR & LPR-200 sensor pinout>>image:ANU_seismometer_connection.png]]
257 -
258 -
259 259  )))
260 260  
261 261  (% class="col-xs-12 col-sm-4" %)
... ... @@ -295,8 +295,6 @@
295 295  
296 296  
297 297  
298 -
299 -
300 300  (% class="box" %)
301 301  (((
302 302  = TerraSAWR Specs =
... ... @@ -360,7 +360,5 @@
360 360  
361 361  
362 362  
363 -
364 -
365 365  
366 366  )))
ANU_seismometer_connection.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.robert
Size
... ... @@ -1,1 +1,0 @@
1 -54.0 KB
Content