Skip to Content

Changes for page ANU Seismic Data Loggers

Last modified by robert on 2025/09/16 13:22
From version 66.1
edited by robert
on 2025/09/16 13:19
Change comment: There is no comment for this version
To version 63.1
edited by robert
on 2025/08/08 16:05
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -26,14 +26,6 @@
26 26  (% class="wikigeneratedid" %)
27 27  In the case of an LPR, there is a large compartment for housing an internal battery, able to accommodate anything from a 10-30Ah battery. To use a standard lead acid battery with a positive and negative terminal, a 6 pin adaptor must be used. This ensures the voltage from the external power port (pins A and C) connect to the battery and ensure the system actually recharges. (See [[Peripheral Equipment>>doc:Instrumentation.Peripheral Equipment.WebHome]] for a more comprehensive overview of this kind of setup)
28 28  
29 -= GPS Considerations =
30 -
31 -GPS is required for the data to have accurate timestamps. A standard 3-5V 1575.42 Mhz coaxial cable works fine and can be found for relatively cheap (e.g. [[https:~~/~~/www.elecbee.com/en-3555-gps-antenna-bnc-male-for-garmin-gps-120120xl125-sounder-with-cable-2m) >>https://www.elecbee.com/en-3555-gps-antenna-bnc-male-for-garmin-gps-120120xl125-sounder-with-cable-2m]]
32 -
33 -The TerraSAWR has a built-in GPS but this doesn't work as well, especially if the logger is (wisely) buried. **The LPR does NOT have a built-in GPS antenna, so an external antenna is mandatory.**
34 -
35 -In a pinch, a severed or broken antenna can be mended back together relatively easily by non-experts. Even stripping the wire and twisting it back together by hand on site is possible!
36 -
37 37  = Data Card Formatting and Information =
38 38  
39 39  Both the TerraSAWR and LPR-200 require SD Cards to be formatted in FAT32 filesystem. For 64Gb cards it can be difficult to format in FAT32, but [[software >>http://auspass.edu.au/field/fat32cardformatter.exe]]is available. ANU recommend SanDisk Extreme 150 mb/s cards in either 32 or 64Gb size. We strongly discourage using cards larger than 64Gb, and in general smaller cards are less likely to fail. We have also found that "adapter" cards (e.g. SD to microSD) are prone to having write issues and **strongly** advise against them.
... ... @@ -40,8 +40,7 @@
40 40  
41 41  The loggers can be "pre-programmed" with information (e.g. site name, sampling rate, etc) or they can be programmed in the field using the buttons on the logger. To pre-program the cards you simply edit a text file (named "[[ANUSRSetup.txt>>http://auspass.edu.au/field/ANUSRSetup.txt]]" for the LPRs, or "[[tSAWRSetup.txt>>http://auspass.edu.au/field/tSAWRSetup.txt]]" for the TerraSAWRs) and place it in the root directory on the SDCard. When the logger boots up, it will parse and load this information.
42 42  
43 -(% class="wikigeneratedid" id="HTheformatforANUSRSetup.txt2FLPR200swillbeasinglelineoftextthatlookslikethis:" %)
44 -The format for ANUSRSetup.txt / LPR200s will be a single line of text that looks like this:
35 +== The format for ANUSRSetup.txt / LPR200s will be a single line of text that looks like this: ==
45 45  
46 46  {{{XXX195G0100010034864 2 }}}
47 47  
... ... @@ -61,8 +61,7 @@
61 61  NOTE: the 2 at the very end is for "RECORD ON RESTART". The record on restart option ensures that if the logger dies and is powered back up whilst in the field (due to battery charging cycles or other causes) that the recording will resume. (# of blank spaces before this doesn't matter)
62 62  )))
63 63  
64 -(% class="wikigeneratedid" id="HTheformatforTSAWRloggersisshorter:" %)
65 -The format for TSAWR loggers is shorter:
55 +== The format for TSAWR loggers is shorter: ==
66 66  
67 67  (% class="box errormessage" %)
68 68  (((
... ... @@ -81,8 +81,7 @@
81 81   and seismometer serial number (9999).
82 82  
83 83  
84 -(% class="wikigeneratedid" id="HTheformattingprocessusingthelogger:" %)
85 -The formatting process using the logger:
74 +== The formatting process using the logger: ==
86 86  
87 87  The process for formatting an SD card within the logger is straightforward. Navigate to the "SD INFORMATION" screen and press ERASE SD CARD. This process may take up to a minute. This will result in erasing all files from the card. Upon starting recording, a new 'seed' will be written containing all the information that the logger has been set with FINISH THIS SECTION
88 88  
... ... @@ -200,7 +200,7 @@
200 200   Stage 7: FIRResponseStage from COUNTS to COUNTS, gain: 1##
201 201  
202 202  
203 -However, if retrieving from AusPass or IRIS, the 2nd "sensor gain" stage is combined with the logger gain. This has no affect, but you may detect that the former Stage 2 V->V ResponseStage has been merged into the Stage 3 gain.
192 +However, if retrieving from AusPass or IRIS, the 2nd "sensor gain" stage is combined with the logger gain. This has no affect, but will be one stage short:
204 204  
205 205  ##Channel Response
206 206   From M/S (Velocity) to COUNTS ()
... ... @@ -277,9 +277,6 @@
277 277  
278 278  
279 279  
280 -
281 -
282 -
283 283  (% class="box" %)
284 284  (((
285 285  = TerraSAWR Specs =
... ... @@ -335,8 +335,5 @@
335 335  
336 336  
337 337  
338 -
339 -
340 -
341 341  
342 342  )))